Pro-Form Crosswalk 395 User manual

395
Model No, 831,24833.0
Serial No.
Writethe serial numberinthe space
abovefor reference,
Decal
* Assembly
. Operation
* Maintenance
• Part List and Drawing
Sears, Roebuck and Co.
Hoffman Estates, IL 60179
TREADMILL EXERCISER
User's Manual

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................... 2
IMPORTANT PRECAUTIONS ..................................................... _............ 3
BEFORE YOU BEGIN ........................................................................ 5
PART IDENTIFICATION CHART ................................................................ 6
ASSEMBLY ................................................................................ 7
OPERATION AND ADJUSTMENT ............................................................. 13
HOW TO FOLD AND MOVE THE TREADMILL ................................................... 19
TROUBLESHOOTING ...................................................................... 20
EXERCISE GUIDELINES .................................................................... 23
PART LIST ................................................................................ 24
EXPLODED DRAWING ...................................................................... 25
ORDERING REPLACEMENT PARTS ................................................... Back Cover
90-DAY FULL WARRANTY ........................................................... Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(a)
of the warning decal(s). If a decal is
missing or illegible, call 1_888-533 -
1333 and request a free replacement
decal. Apply the decal in the location
shown. Note: The decaI(s) may not be
shown at actual size.
KEEPHANDSANDFE_AWAY
FROMTHISAREAWHILETHE
TREADMILLISINOPERATION,

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN
Thank you for selecting the new PROFORM ®
CROSSWALK 395 treadmill, The CROSSWALK 395
treadmill provides an impressive selection of features
designed to make your workouts at home more effec-
tive and enjoyable,
For your benefit, read this manualcarefullybefore you
use the treadmill, if you have questions after reading
this manual, please see the back coverof this manual,
To help usassist you,note the productmodel number
and serialnumberbefore contactingus,The model
numberand the location ofthe serial numberdecal are
shown on the front coverof this manual
Before readingfurthez, please familiarize yourselfwith
the partsthat are labeled in the drawingbelow.
Length: 5 ft. 5in, (I65 era) |
Width: 2 ft. 9 in, (84 em) /
Storage
Crosswal
Walking Belt
Foot Rail
Idter Roller
Ad}ustment Screws
Console
Hoed
Wheel
Platform Cushion

PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assemb]y. The number in parentheses betcw each draw-
ing is the key number of the part, from the PART LIST near the end of this manual, The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached, tf it is not, ca[J 1-888-533-1333, Extra hardware may be included.
I/4" Star Washer
(23)--4 3/8" Star #8 x1i2" Ground #8 x 3/4" Screw
Washer (3)-t0 Screw (I)-1 (4)-4
#8 x !" Screw 1/4" x 31/2" Screw (56)--4
(7)-4
#10 × 1 _12"Screw
(8)-2 3/8" × 3 1/4" Screw (2)-6 D

ASSEMBLY
- Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials, Do not dispose of the packing
materials until you finish assembly,
•The underside ofthe walkingbelt is coated with
high-performancelubricant. After shipping, there
may be some lubricanton topof the walkingbelt
or on the shipping carton.Thisis normal. Jfthere
is lubrica._ton top of the walkingbelt, wipe itoff
withasoftclothand a mild, non-abrasive cleaner.
-TOidentify small pans. see page6.
•Assemblyrequiresthe following tools:
the includedhexkeys I_=
one Phillipsscrewdriver
SCissors _===;z_
•Toavoid damagingparts, donot use power tools,
1. Make sure that the power cord Is unplugged.
Remove and discard the two screws(A) and the
shippingbracket (B) fromthe rightside ofthe
Base (74). Then, remove and discardthe screws
and shippingbracket (notshown)from the [eft
side ofthe Base.
74
2. With the help of asecond person, tip the tread- 2
mill onto its left side. Partially pivot the Base (74)
to hetp stablize the treadmill.
Pull the Upright Wire (63) and the ground wire
through the indicated hole in the Base (74).
Attach the ground wire to the Base (74) with a#8
x 1/2" Ground Screw (t).
See the inset drawing, Cut the plaslic tie near
the Upright Wire (63). Be careful not to dam-
age the Upright Wire.
63
.Ground Wire

Press a Base Cap (70) into the Base (74).
Make sure that the Upright Grommet (73) is
pressed into the square h(!le in the Base (74).
J
70
Square
Hole
4. identify the Right Upright (76), which is marked
"Right," Have a second person hold the Right
Upright near the Base (74).
See the inset drawing. Tie the wire "tie in the
Right Updght (76) securely around the end of
the Upright Wire (63). Then, insert the Upright
Wire into the lower end of the Right Upright as
you pull the other end of the wire tie through the
Right Upright.
4

HoldtheRight Upright (76) against the Base
(74). Re careful not to pinch the wires.
Partially tighten three 3/8" x3 114" Screws (2)
w_th three 3/8" Star Washers (3) into the Right
Upright and the Base; do not fully tighten the
Screws yet.
With the help of a second person, tip the
treadmill onto its right side. Press in a Base
Cap (not shown) and attach the Left Upright
(not shown) as described in steps 3 and 5.
Note: There are no wires on the left side.
Identify the LeftandRight Handrails (59, 64),
which are marked "Left" and "Right," Remove the
four 5/16"x 314"Screws (5) and four 5/16 =Star
Washers (8)from thebottoms and sides of each
Handrail,
Held the RightHandrail (64) near the Right
Upright (76). Insertthe wiretie onthe Upright
Wire (63) through thehole in the bottom and
out ot the hole in the sideof the Left Handrail as
shown, Then, pullthe Upright Wire throughthe
RightHandrail ......................
Attach the Right Handrail(64) tOthe Right
Upright(76) withtwoof the 5/I6" x3/4" Screws
(5) and two of the 3/'8"Star Washers (6) that
you jUStremoved,Make sure not to pinch the
Upright Wire (63), Start both Screws, and
then tighten them,
Attach the Left Handrail (59) to the Left UpTight
(66) as described above. Note: There are no
wires on the left side.

Position 1he Console Crossbar (61) between
the Left and Right Handrails (59, 64) with
the Console Ground Wire (47) positioned as
shown.
Attach the Console Crossbar {61) to the Left
and Right Handrails (59, 64) with the other four
5/15" x 314" Screws (5) and the other four 5/t6"
Star Washers (6) that you removed in step 6,
Start all four Screws, and then tighten them.
47_
61 64
B. With the help of a second person, hoJd the con-
sole assembly near the Right HandraiI (64).
Connect the Upright Wire (63) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place, tf they do not, turn one connector and try
again, IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER, Then. remove the Wire tie from
the Upright Wire.
Connect the Console Ground Wire (47) on the
Console Crossbar (61) to the ground wire on the
console.
[
Console I
Wire ._
lO