Pro-Ject Audio Systems Head Box S User manual

INSTRUCTIONS FOR USE
Pro-Ject Head Box S

© Audio Trade GmbH · Pro-Ject Head Box S · Revision 2011.11.15
2
Dear music lover,
thank you for purchasing a PRO-JECT AUDIO headphone amplifier.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Connection to the amplifier (recorder)
Connect the TAPE / RECORD OUT RCA/phono sockets from your amplifier to the In RCA/phono sockets of
the headphone amplifier. The Out RCA/phono sockets of the headphone amplifier can be connected to the
input sockets of your recorder.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the left
channel black or white.
Pro-Ject Audio Systems, Vienna, Austria
In Out
Right
LeftLeft Right 18V
Connecting the headphones
Connect the headphones to the ¼“ (6,3mm ) jack socket on the front of the headphone amplifier. Use the
control knob to adjust the level to the required volume.
!
Please turn the volume level to minimum before connecting the headphone.
Minimum impedance of the head phone 30ohms.
Headphone replay
Use the input selector of the amplifier to choose the source you wish to hear.
Mains power connection
The headphone amplifier is supplied with a power supply suitable for your country's mains supply. Check the
label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage
plug from the power supply to the Power 18V "socket before connecting the power supply to the mains.
To switch on from standby or to standby
The button on the left hand side will toggle the unit between its fully operational status and standby. The blue LED
on the front panel shows that the unit is powered on.
Technical specifications Pro-Ject Head Box S
Power output: 330mW/30ohms, 60mW/300ohms
Headphone connection: >30ohms
Signal to noise: 95dB (112dB - A weighted) at full output
Frequency response: 30Hz – 20kHz/-0,05dB (10Hz – 120kHz/-1dB)
THD (IMD): 0,003% (0,002%)
Gain: 11dB
Headphone jack: 3-pole ¼“ (6,3mm ) co-axial jack
Line-level output: 1 pair RCA/phono sockets
Outboard power supply: 18V/500mA DC, suitable for your country's mains supply
Power consumption: 18V/100mA DC
Dimensions W x H x D (D with sockets): 103 x 36 x 104 (109)mm
Weight: 600g without power supply

© Audio Trade GmbH · Pro-Ject Head Box S · Revision 2011.11.15
3
Potential incorrect use and fault conditions
No signal on one or both channels:
No connection between headphone and headphone amplifier ore amplifier. This could be due
to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Headphone does not work:
Headphone volume control is at minimum.
Amplifier Tape-Monitor circuit is not activated.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or change to any part of the product by unauthorized persons release the
manufacturer from any liability over and above the lawful rights of the customer.
PRO-JECT is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Audio Trade GmbH
Copyright © 2011. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.