PRO SIGNAL PSG3449 User manual

1
1x4 4Kx2K SPLITTER OVER CAT 5/6
PSG3449

2
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
When using electrical appliances basic safety precautions should always be followed.
• To prevent re or shock hazard, do not expose this product to rain or moisture.
• Check that the power supply matches the mains voltage.
• Only use the power supply provided or one of identical specication.
• Ensure the IR remote extender cables are connected to the correct devices.
• Beware of static electricity which may damage the device. Use ESD precautions
when installing.
• Do not plug or unplug cables while the devices are powered on.
WHAT'S INCLUDED
• 1 x HDMI splitter, 4 x receivers
• 5 x Power Adapter 230VAC to 5VDC 2A
• Operation Manual
• 1 x IR remote transmitter, 4 x IR receivers
• Distribute 1 HDMI source to 4 HDMI outputs.
• Supports full HD resolution 1080p@60Hz.
• Plug and play setup.
FEATURES
CAT CABLE REQUIREMENT
Follow the standard of IEEE-568B, It is recommended to select a high quality network
cable with less loss and crosstalk.
1 orange/white
2 orange
3 Green/white
4 Blue
5 Blue/white
6 Green
7 Brown/white
8 Brown
OVERVIEW
Rear Panel

3
INSTALLATION
This HDMI splitter allows a source HDMI signal to be split to 4 receivers and displays
over a range of up to 120meters at 1080p resolution using a CAT5/5e/6 network cable.
Requirements:
1. HDMI source device (PC, DVD, PS3) HD monitoring equipment etc.
2. Up to 4 HDMI display devices eg: SDTV, HDTV, projector with HDMI port.
• Connect the HDMI input on the splitter with the source device.
• Connect the splitter TX RJ45 output ports to the receivers either using CAT5 or
better cable.
• Connect the IR receivers to each HDMI receivers and the IR transmitter to the
splitter.
• Connect the receiver HDMI outputs to the destination display devices.
• Connect the power supply output to the switch 5V DC inputs and the 5V DC inputs
on the receivers then connect all the PSU to the mains and turn on the power. The
power LED on the front panel will illuminate.

4
SPECIFICATIONS
Voltage/Current DC 12V 2A
Power consumption <10W
HDMI compliance HDMI 1.3
HDCP compliance HDCP 1.4
HDMI resolution 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
IR signal Support 20~60kHz IR device
Network CAT5/5e/6 <80m/<100m/<120m
Working temperature 0~60°C
Storage temperature -30~ 70°C
Humidity 0~90%RH (no condensation)
Dimension (splitter) 252(W) x 97.5(D) x 25(H)mm
Material Alloy
Weight (splitter) 535g
CLEANING & MAINTENANCE
Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling
of the materials used. Contact your local authority for details of recycling schemes in
your area.
Made in China. PR2 9PP
Man Rev 1.0
IR User Guide:
• IR receiver extension cable should be connected to the IR IN port of the receiver.
• The IR emitter extension cable should be connected to the IR OUT port of the
transmitter.
• The emitter of the IR extension cable should face as close as possible to the IR
receiving window of the source device.
• Face the receiving head of the IR receiver extension cables toward the user for
unobstructed line of sight to the remote control.
• The IR receiver detects the users remote control and transmits the signal down the
network cable to the IR emitter which replicates the IR output to control the source
device.