PROAIM JB-CMTM-01 User manual

1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Comet Mini 4.5 Euro/Elemac Camera Jib (JB-CMTM-01)
Assembly Manua l
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
Proaim 2.5 Comet Mini Jib
1 x 2 Extension Arm
2 x Counter weight Rods
1 x Extension rod
Flight Case

2
Comet Mini Jib Setup
• Place the euro adapter plate (Not Included)
to the center hole of the Spin Dolly
(Not Included).
• Aach the euro adapter plate (Not Included)
to the Spin Dolly (Not Included) with the help
of the bolt and then ghten it using the Allen
key.
• Aer mounng the Flexino Bazooka
(Not Included), secure it by properly
ghtening the ratchet knob.
• Loosen the ratchet knob of the Flexino
Bazooka (Not Included) and mount it on the
euro adapter (Not Included) placed on the
Spin Dolly (Not Included).
• Similarly, ghten all the other bolts to rmly
secure the euro plate adapter (Not Included).
• Place the Comet Jib onto the euro adapter of
center column.

3
• Fix the jib fork with the center column by
locking the knob via locking lever.
• Comet Jib is properly aached.
• Re-Insert the side knob to lock it.
• Loosen the knob located at one of ends of the
jib, & pull out the telescopic secon, as
shown in the image.
• Then pull & take out the side knob of the jib.
• Unlock the rod pin, Then insert the
counterweight rod through the hole.

4
• Then add weights (Not Included) on both the
rods accordingly and secure them with the
locking pins.
2 dierent length rods of counterweight for easy balancing
Dynamic Moves For Your Camera Varied Tilng Range for Varied Lengths
NOTE: It comes with two counterweight rods that let you hang dumbbell weights for
counterbalancing.

5
• The Comet jib provides 360° rotaon with its
panning knob.
• Loosen and remove the adapter knob present
on the front of the Comet jib.
• Aer mounng the uid head, aach the
castle ring to the boom of the uid head.
• Now, properly secure the oset bracket
(Not Included) by ghtening the ratchet knob
and adapter knob.
• Loosen the ratchet knob of the oset bracket
(Not Included) and mount it on the front
secon adapter of the jib.
Mounng of Fluid Head
• Loosen the Castle Ring of the Fluid Head
(Not Included) and mount it on the Oset
Bracket.
360°
panning

6
Extend the length of Comet Jib
• Push the knob present on the front secon of
the comet jib and properly remove it.
• Aach the Camera Plate to the Camera
(Not Included) by matching the threads and
properly secure with the help of a screwdriver
(Not Included).
• Now, secure it with the castle nut.
• Push the buon of the Fluid Head
(Not Included) and remove the Camera Plate.
NOTE: The Comet can be combined with
addional Proaim accessories, Suitable for all
standard Euro / Mitchell Remote Head systems.
• Slide the Camera onto the Fluid Head and
properly lock it with the help of the locking
pin.

7
• Now ,securely re-insert the push pin.
• Firmly secure the ratchet knob by ghtening
it, as shown in the image.
• Now, loosen the ratchet knob present on this
knob.
• Remove the pushpin present on the top rod
of the front secon by pushing it.
• Loosen and remove the ratchet knob present
on the back side of the Jib.
• You can set the required height by removing
the push pin present on the top most rod of
the Comet Jib.
Extend the length of Comet Jib

8
• The extension arm is successfully aached to
the Comet Jib.
• Now, re-insert and ghten the ratchet knob.
• Properly remove the extension arm by loos-
ening it.
• Insert the extension arm into the Comet Jib.
• Now, detach the front secon of the jib ,as
shown in the image.
Assembly of Extension Arm

9
• Carefully align the extension rod with the rod
of the Comet Jib and aach it.
• Insert the head secon of the Comet Jib on
the extension arm.
• Now, insert the rod of the head secon into
the hole of the extension rod.
• Then, ghten the ratchet knob of the Jib.
• Aer inserng the rod, secure it with the help
of the pushpin.
• Now, insert the push pin to secure the rod.
Assembly of Extension rod

10
• Loosen the ratchet knob of the head secon
of the Jib.
• Now, properly ghten the ratchet knob of the
head secon to secure it in its place.
• Loosen the adapter knob present on the head
secon with the help of Allen key.
• Remove and aach the safety cap of the
boom rig (Not Included) to the head secon
of the Jib.
• Now, remove the adapter with ease.
Assembly of Boom Rig