PROAIM P-PTBH-01 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
PhotoBooth Studio Kit - Camera
Plaorm (P-PTBH-01)
Assembly Manua l
22" Telescoping Arm
Vesa Studio Monitor
Mount for Stand
Arculang Arm
Camera Plaorm
Cold Shoe Mount
(Baby Stud Adapter with
1/4″ 20 female thread on
one side and 3/8″ female
thread
on the other side)

2
 Mount the monitor mount on the C-stand and
ghten it using the back knob.
Note: Monitor Mount is the best way to mount
your LCD monitor on a C-stand, light-stand, or
other stands with 5/8" baby pins/studs.
 The images show that you can move the
monitor mount up and down up to 90° using
the side knob.
 Set the monitor mount at the desired posion
and secure it properly using the knob. Loosen
the knob to remove the monitor mount.
Mount it on the stand via the 2nd mounng
point.
Note: Monitor Mount has two side mounng
opons to change the direcon of the monitor.
 Change the direcon according to your
requirements and ghten the knob from the
2nd side to secure the monitor mount.
Monitor Mount Setup
 Screw together the LCD and the monitor
mount and secure them properly using an
Allen key, as shown in the image.
Note: The monitor is mounted via four screws.
Once secured, you can lt the monitor to any
viewing posion by the provided knob.
Note: You can mount your at-panel monitor up
to 32" (diagonally measured).

3
 Loosen the knob of the arculang arm, and
open the arm completely. Align and insert the
arm into the thread on the monitor mount.
Note: The arculang arm is movable and helps
move the camera's direcon.
 Once the arculang arm is inserted, secure it
correctly with the help of the knob, as shown
in the image.
 Mount the camera plaorm on the arculang
arm and secure it using the center knob.
Note: Robust Camera Plaorm allows you to
safely mount a camera to the arculang arm,
as shown in the image.
Arculang Arm Setup
Note: Camera Plaorm has 1/4 "-20 & 3/8 "-16
threaded camera studs and two 5/8" receivers
to mount compable accessories of your choice.
Camera Plaorm Setup
 To change the camera's movement, loosen the
knob of the arculang arm, set the direcon,
and ghten the knob back.

4
 Loosen the knob of the cold shoe mount, and
extend it completely.
Note: Cold Shoe Mount Baby Stud Adapter has
1/4″ 20 female thread on one side and 3/8″ fe-
male thread on the other side.
 Insert the 22" telescoping arm into the
monitor mount and secure it with the help of
the knob.
Note: You can use the Proaim 20" Telescoping
Arm for everything from overhead lighng to
stand extension.
Note: Twist the knob, and the aluminum arm
telescopes from 11.5" to 20" in length. Each end
has a 5/8" stud topped with 3/8" threads for
receiver or screw-in mounng opons.
 Aer extending the length of the telescoping
form, secure it through the knob.
22” Telescoping Arm Setup
Cold Shoe Mount Setup
 Images showing dierent arm movements.
 Mount the cold shoe mount on the telescopic
arm and secure it with the knob.

5
 Image showing Monitor Mount, Arculang
Arm, Camera Plaorm, 22" Telescoping Arm &
Cold Shoe Mount assembled adequately.
 Insert the umbrella into the clamp and secure
it correctly with the knob.
Note: This umbrella has been specially designed
for the photobooth setup.
 Image showing umbrella assembled
adequately.
 Slide the ash onto the cold shoe mount and
ghten it with the help of a bolt.
Note: With the Photobooth Kit, you can aach
a camera on the camera plaorm, a display on
the monitor mount, a ash on the cold shoe
mount, and an umbrella o qn the clamp.
 Image showing a praccally complete booth
with a camera, display, ash, and umbrella.

6
YOUR PROAIM PHOTOBOOTH STUDIO KIT - CAMERA PLATFORM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.