PROAIM Cinema Breeza Pro DL-BRZP-01 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Breeza Pro Camera Dolly with Track|Mitchell (DL-BRZP-01)
Assembly Manual
Proaim Breeza dolly
(with track wheels)
4 x Rods Bag Packing
2 x Female Connector Rods
4 x Male Connector Rods
75mm Bowl Adapter
2 x End Spacers
100mm
Bowl Adapter
2 x Safety Hooks

2
• Properly secure the female connector rod to
the male connector rod, as shown in the
image.
• Repeat the same process for the second set of
connector rods.
NOTE: To increase the length of the track,
securely aach all connecons.
• Loosen the knobs of both the feet of the end
spacers and open the clamps.
• Now insert both the connector rods in the
clamps.
NOTE: It has four adjustable feet that come with
the end spacers, oering you a mounng
soluon for any lming environment.
• Follow the same process to insert the
connector rods in the second end spacer from
the other side.
NOTE: The track can be used at two dierent
lengths- 4 and 6- suing your setup
requirements.
Assembling of Connector Rods
Assembling of End Spacers
• Aer inserng both the connector rods,
ghten the clamps with the help of the knobs.

3
• Mount the Breeza Pro Camera Dolly onto the
4 track.
NOTE: Follow the same process to mount the
Breeza Pro Camera Dolly on the 6 track.
• Then properly ghten with the help of the
knobs .
NOTE: The Dolly comes equipped with sixteen
rolling track wheels that run smoothly on tracks
and a at surface, and it has double ball
bearings for ultra-smooth performance.
• Loosen and remove the knobs of both the
Safety Hooks.
• Follow the same process to insert the other
two rods.
NOTE: It has end-spacers that let you aach the
speed rails securely; they can also be mounted
to tripods for an alternave shoong setup.
• Loosen the knobs of the end spacers, open
the clamps and insert the rod. Follow the
same process to insert the second rod as well.
Breeza Pro Camera Dolly Setup

4
• Loosen the knob of the Fluid Head (Not
Included) and mount it on the 75mm bowl
adapter.
• Aach the safety hook at the boom side of
the Breeza Pro Camera Dolly and properly
ghten it using the knob.
• Aer inserng the Fluid Head (Not Included)
properly ghten it with the help of the locking
knob.
• Push the red ratchet knob of the uid head to
remove the camera plate.
Mount Fluid Head on Bowl Adapter
• Follow the same process for the second hook.
NOTE: Safety hooks can be aached to the
boom of the Dolly to act as security against
pping, ensuring your plaorm doesn't get
knocked o the rails.
• Adjust the height of the track with the clamp,
as per your requirements.
NOTE: Clamps at the top allow for telescopic
height adjustment providing ample elevaon for
dierent shoot setups.

5
• Aach the 75mm bowl adapter to the boom
of the Breeza Pro Dolly and insert all the
screws.
• Remove all the screws of the 75mm bowl
adapter using a screwdriver (Not Included).
• Now remove the 75mm bowl adapter, as
shown in the image.
• Mount the camera on the uid head and
again secure properly with the red push pin.
Underslung Camera Setup
NOTE: You can mount Breeza Dolly Setup
without rods on the at surface area.
• Aach the Camera Plate to the camera (Not
Included) by matching the threads and
properly ghten using a screw driver (Not
Included) .
Camera Setup

6
• Remove the Castle Ring from the Mitchell
Plate (Not Included) and mount it on the
Breeza Dolly.
• Mitchell Plate has been mounted on the
Breeza Dolly.
• Now properly aach and secure the Castle
Ring and Mitchell Plate together, as shown in
the image.
• Press the buon on Mitchell Plate to slide the
camera plate.
• Now you can mount your camera (Not
Included) setup, as desired.
Mitchell Setup
• Tighten all the screws with the help of the
screwdriver. The bowl adapter has been
aached to the boom of the Breeza Dolly.

7
• Mount the camera onto the uid head and
properly lock with the help of the push pin.
• Aach the Camera Plate to the camera (Not
Included) by matching the threads and
properly ghten using a screw driver (Not
Included).
• The camera plate has been removed from
Mitchell, as shown in the image.
Camera Setup
• Camera has been mounted to the uid
head.
NOTE: It comes equipped with an integrated
Mitchell mount and 75mm and 100mm Bowl
Adapters, giving you versale camera-heads
mounng opons.
NOTE: Bubble level on Breeza Dolly & End
Spacers helps to check the proper level of
Breeza Dolly with setup.

8
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our ut-
most support and care unl you use our product.
YOUR PROAIM BREEZA PRO CAMERA DOLLY WITH TRACK
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)