PROAIM LT-262 User manual

Instruction Manual
Sunfire LED PAR Light + Flight
Case (LT-262)

2
Subject Page
Foreword 3
Introducon 4
Safety Hints 5
Assembling 6-8
Warranty 9
At Proaim, our goal is to ensure 100% Customer Sasfacon in all that we do.
We back our sales with a 1 year warranty from the date of purchase and work hard
to resolve any problems in the unlikely event one should arise.
With our commitment to connuous improvement and your Feedback, building on
our reputaon of providing aordable, quality products is
PRIORITY #1.
Table of Contents

3
Dear Client,
On behalf of all the people that work so hard to provide you with the most
up-to-date, exible and cost-ecient producon gear, we would like to welcome
you into the Proaim family.
By purchasing your Sunre LED PAR Light, you have just joined a host of designers,
engineers, machinists, assembly, customer service and oce sta that take great
pride in all that they do. Our mantra of connuous improvement has been the
guiding principle of how we conduct our business since day one.
Once you have the opportunity to experience your Sunre LED PAR Light, we hope
you will agree that we cra quality products at a compeve price. Products
designed to meet and exceed the standards of today’s real producon world.
Standards set by our valued clients and standards we strive to maintain.
With Best Wishes,
Proaim Team
Welcome To Proaim!

4
Sunre Daylight LED PAR Light by Movolms is the most powerful led lighng kit on
the market; all while using less than 2 amps of power. Whether for Broadcast ENG
remote eld producon, live sports coverage, xed studio installaon, video shoots
or lm, led light provides a wealth of lighng benets and features ideally suited to
a wide range of lighng applicaons.
Please inspect the contents of your shipped package to ensure you have received
everything that is listed below.
Note: If you have purchased (LT-262-00) kit, you will receive the following:
Introducon
What’s In The Box
 1 * Movolms Sunre Daylight 5600K
 1*15 Degree Diuser
 1*30 Degree Diuser
 1*55 Degree Diuser
 1*Color Filter
 1*Diuser Bag
 1*Barn Door
 1* Flight case
 1*Plugs (US, UK, AU, EU)
 1 * Movolms Sunre Tungsten 4000K
 1*15 Degree Diuser
 1*30 Degree Diuser
 1*55 Degree Diuser
 1*Diuser Bag
 1*Barn Door
 1* Flightcase
 1*Plugs (US, UK, AU, EU)
Note: If you have purchased (LT-262-01) kit, you will receive the following:

5
Safety Hints
ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT SERIOUS DAMAGE TO
THE GEAR!
 This light is intended for indoor use only.
 Only qualied and cered personnel should perform installaon, not for
household use.
 These lights should always be installed/mounted in a stable and secure locaon.
 Always allow adequate venlaon of the light. Never cover or, in any way,
obstruct the louvered openings in light.
 Make sure that light is only used in dry locaon. Do not use light in or around
falling water, wet locaons or moisture.
 Never look directly into the light source while the xture is turned on. Light
source is very bright and could cause damage to eyes.
 Do not probe or touch any interior features of the xture. This includes LED
sources inside the barrel of light. Doing so may cause damage to the xture
and/or may present a shock or burn hazard.
 Always make sure that the light xture is connected to proper power source
with proper voltage and current rangs. Also, make sure that adequate
over-current protecon is provided for the circuit as well.
 This light contains no-user serviceable parts. Do not open the light housing or
aempt any repair or modicaon of the light. Failure to observe this warning
could result in damage to the light, injury and/or voiding the limited warranty.
 Inserng objects or ngers inside any openings or connectors could result in a
shock hazard/injury and damage to the light.
FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER IMAGES AND TROUBLE FREE
OPERATION.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS
AVAILABLE ‘ONLINE’ BY CONTACTING YOUR SALES REPRESENTATIVE.

6
Assembling
 Make note of the locaon of inputs and
outputs along with light controls found
on its Control Box, as shown.
Unpacking Instrucons
Immediately upon receipt of this light, carefully inspect the packaging for any
obvious signs of damage from mishandling or exposure to elements. If any is noted,
please provide this informaon to the shipper immediately so that proper claims
can be processed. Place packaging in upright posion (with labelling and markings
in readable orientaon) and open the top end of carton. Remove the light and
associated material from carton and place them on a stable surface or mounng
conguraon using the provided yoke and yoke pin mounng system.
NOTE: The AC & DC Power Cables will be found e-wrapped & coiled-up inside the yoke aached
to the power supply, inside the shipping container.
 Uncoil the AC and DC Cord, plugging the DC female end into DC power input, located on back
of Control Box (shown above).
 NOTE: Lights operate on grounded 110v – 240v, 50/60Hz AC Input. AC Supply Source must be
sized properly and has approved protecon circuitry for safe operaon. Take care to observe
all proper precauons when connecng power.
 NOTE: If the external exible cable or cord of this light is damaged, it shall be exclusively
replaced by contacng us or a similar qualied person, in order to avoid hazards.
 Plug the male end of AC Power Cord into an appropriate AC power source.
 Turn on the Light by pressing Power Switch, located at the back of Control Box.

7
AC Power
Sunre Lights operate on standard single-phase AC power.
 Input Voltage Range: 100 – 240Vac
 Input Frequency Range: 50/60 Hz
NOTE: Standard Power Cord supplied with Sunre Light is intended to connect with standard,
single-phase 110-120Vac, 60 Hz USA circuit. An adaptor for use with 240Vac, 50Hz European
circuit is also included. Other power cords for connecon to other countries’ single-phase circuits
are available as opons. No other special adjustments or changes are required for operaon at
internaonal voltages.
WARNING: Never connect Sunre Lights to anything other than a single-phase circuit.
Connecon to three-phase power can/will cause serious damage and/or bodily injury.
Funconal Requirements
The following secon provides all the funconal requirements for Lights Rotang Selector
Value – 00 – manual dimming using potenometer on the front panel.
DMX Mode
 This mode shall be acve when the Address switch is set to DMX.
DMX Controller Interface Requirements
 The soware shall accept input from the DMX512 controller that represents user requested
values for Brightness.
 Upon Power Up, the factory default seng will turn the light immediately to its full
brightness, unless any other specic “Power On” seng has been previously programmed
into the light.
 Using the selector switch located on the right side of the control box select the desired mode
in which you wish to operate the light i.e. local or DMX.
The DMX input to the light is mapped as follows:
Channel 1:
Brightness: 0 – 255
One light need 1 DMX channel.

8
Rotang Selector Code Table:
00 – Manual dimming
01 – DMX channel 1 – Light 1 dimming
02 – DMX channel 2 – Light 2 dimming
03 – DMX channel 3 – Light 3 dimming
04 – DMX channel 4 – Light 4 dimming
…
…
…
…
99 – DMX channel 99 – Light 99 dimming
NOTE 1: DMX electrical signal is received from DMX-IN connector and amplied, then sent
through DMX-OUT connector to next light equipment. This way each light equipment is
funconing as a DMX Repeater. The menoned feature provides a long single DMX signal branch
connecons (up to 99 lights) at long distances.
In case when the current light equipment is in Power Down condion, then a special By-Pass relay
provide input signal to the output (not amplied); this way all the connected light equipment
devices connue to funcon with full DMX features.
NOTE 2: The DMX signal circuitry is fully electrically insulated from the internal circuit of light.
This way no hazard or inuence of the electrical circuit in any light equipment could spoil the
voltage potenals of DMX connecng cables and wires.
NOTE 3: The thermal management of the light is based on sensing a high temperature (+65°C
inside the light), when the RED front LED goes to ON condions. In such a condion, use of the full
power is no more recommended – please decrease the power at least with 20%, due to the higher
environment temperature.
In case temperature is higher than the described limit (+75°C inside the light), the emergency OFF
condion is eectuated and lamp goes to OFF mode (RED LED is sll ON). In such a case, leave the
light to become cool or take it away from hot environment, and then the funcon will be restored.
General Maintenance and Care
When not in use, Sunre Light should be stored in a dry and dust-free area. General Maintenance
and Care consists of making sure that the light always has good venlaon and that nothing is
obstrucng free air ow through and around the light. Do not use chemicals to clean it. Any
cleaning of the light, especially LED opcs, should be with a damp (not wet) so cloth, which is
non-abrasive.

9
YOUR MOVOFILMS SUNFIRE LED PAR LIGHT
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
WARRANTY
We oer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
crasmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
dues are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequenal damages resulng from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers aer the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. Aer that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without rst geng a response and geng the approval to send back
the item.
In case of any kind of dissasfacon, we urge you to Contact us immediately and we shall do our
Best to help you out. For any other assistance you can reach us via email.
For any other assistance you can reach us via email.