Prodigit 2055B User manual

Model 2055B
Energy Monitor with Standby Killer Operation Manual
Thank you for purchasing the 2055B Energy Monitor with Standby Killer. This operating manual will provide an overview of the product,
safety instructions, a quick guide to operation, and complete instructions for correct usage. Take the time to completely review these
instructions as well as safety warnings to ensure your best use of the product.
Now you can use this Energy Monitor with Standby Killer unit to check your appliance spend you how munch money, CO2emissions, and as
a standby killer to shunt down your appliances when they are not used, they are on standby condition. The unit combines human motion by
PIR (Pyroelectric Passive Infrared) sensor detection, and appliance’s standby power level, to control AC power on or off automatically. AC
power by demand, people come, AC power on; people absent,AC power off, save energy, save CO2emissions to protect our only one earth.
Advanced features also included:
Monitoring Voltage, Amperage, Watt, KWH, Elapsed Time, Costs and CO2emissions.
Displaying SAVE Amperage, Watt, KWH, Elapsed Time, Costs and CO2emissions.
Over current, safe power to your expensive equipments.
Zero power crossing switches provide a spike free ON/OFF relay control to prolong your appliances usage life.
Now you’ll know how much power your entire appliances are using, and saving power by Energy Monitor with Standby Killer. With the
innovative Energy Monitor with Standby Killer you’ll have peace of mind in more ways than one.
Safety Instructions:
The operating voltage is limited to +/- 10% of Line voltage 230Vac. Do not use it in other voltage rating.
The maximum output current is 13A.
To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service
personnel.
There shall be a statement in the instructions that, if the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
Measurement category II is for measurements performed on circuits directly connected to the low voltage installation.
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service
personnel.
Feature Locations:

Feature Locations:
ON / OFF Key
PIR Sensor
PIR and Display Unit
5-foot tethered Cord
Outlet Unit
Socket
Front View
Rear View

Display Panel:
Installation:
1. Turn off the appliance before connection to the unit and remove the power cord from the outlet.
2. Plug the appliance’s power cord into the Energy Monitor with Standby Killer unit socket, and then connect the Energy Monitor with
Standby Killer into the outlet.
3. If there are many appliances, please use power strip, plug all appliances power cord into power strip’s sockets and plug power strip
into Energy Monitor with Standby Killer socket, then connect the Energy Monitor with Standby Killer into the outlet.
4. Turning the appliance into its Standby mode within 10 seconds. If it is TV, please don’t turn on it, it is Standby mode now; if this
appliance with 2 step switch, off→Standby→on, please turn it on Standby mode.
5. Now the Energy Monitor with Standby Killer will measure appliance standby power, the key on the top of the Energy Monitor with
Standby Killer shall be flash in green light per second, which indicate standby power is measuring. After 30 to 40 seconds, standby
power measuring is finished; key’s light shall be in green. Now, it is working and in PIR detect human motion mode.

ON, OFF and PIR detect function:
1. Pressing the key will turn off power to outlet at once. The key will illuminate in red. The unit will continue to measure power (e.g.
Voltage, Time) and the function keys and LCD display will continue to operate.
2. Pressing the key will turn power on to outlet at once. The key will illuminate in green. The unit features a spike-free switch function
which activates at zero-crossing and will present clean power to your connected appliance. The unit will measure power and the
function keys and LCD display will operate. Now it also activate PIR detect human motion function.
3. If nobody in the PIR effective area, and appliance is on standby condition, the unit will turn off power according to off power delayed
time setting, for example, it is 30 minutes, after 30 minutes, the unit shall shunt down power, LED flash in green light every 3 second,
and the unit also activate PIR detect human motion function. When somebody moves into the effective PIR area, the unit will turn
power on to outlet at once. LED will illuminate in green.
3.1 So there must meet 3 conditions to off power:
A, No body in the PIR effective area,
B, Appliance is on standby condition, and the unit standby off power level is larger than appliance instant standby power,
C,After the unit off power delayed time setting value.
3.2 Please refer to Standby power, Off power delayed time and PIR sensor detecting distances setting for detailed information.
4. Shorter off power delayed time, save more energy, butAC power on/off will be more frequently. Appropriate setting off power delayed
time will be balance to use appliances and save energy, 1 hour for office, 30 minutes for home, is our suggestion.
5. Summary:
5.1 green light = power on, and PIR detect function on.
5.2 red light = power off, and PIR detect function off.
5.3 green light every 3 second = power off, and PIR detect function on.
5.4 green light every second = standby power is measuring, don’t tough.
Remark:
Editing display flashes indicate this item can be re-set.

Cost mode: pressing central key.
It includes $, Total, Day, Month, Year and SAVE.
LCD display default will show Total cost ($) and W.

CO2mode: pressing left key.
It includes CO2, Total, Day, Month, Year, SAVE, and Lb/Kg.
Press
 Change Screen
Key
Press
Press
Press
 Change Screen
 Change Screen
 Change Screen
Press
 Change Screen
Press
Press
Press
 Change Screen
 Change Screen
 Change Screen
$
CO2
-
Meter
$
CO2Meter
$
CO2Meter
$
CO2Meter
$
CO2Meter
$
CO2Meter
$
CO2Meter
$
CO2Meter
-
-
-
-
-
-
-

Meter mode: pressing right key.
It includes W, V,A, Kwh, Elapsed Time and SAVE.
Press
 Change Screen
Key
Press
Press
Press
 Change Screen
 Change Screen
 Change Screen
Press
 Change Screen
Press
Press
Press
 Change Screen
 Change Screen
 Change Screen
 Change Screen
Press
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-
$
CO2Meter
-

$ Rate setting:
Press
Press
Cost Rate
+0.001
Cost Rate
-0.001
Press and Hold
3Second
Press
 Flash Screen
 Change Screen
$
CO2Meter
$
CO2Meter
-
-

CO2Rate and Lb/Kg setting:
Press
Press
Kg-CO2Rate
+0.001
Kg-CO2Rate
-0.001
Press and Hold
3Second
Press
FlashScreen
 Change Screen
FlashScreen
Press
Press
Press
FlashScreen
$
CO2Meter
$
CO2Meter $ CO2Meter
$
CO2Meter
-
-
-
-

Reset (Clear):
Press and Hold
3Second
 Flash Screen
$
CO2Meter
FlashScreen
$
CO2Meter
Press NO
Press YES
Press Press
$
CO2Meter
 Change Screen Change Screen
$
CO2Meter
-
-
--

Human motion controlled PIR sensor detect function:
The key flash in green light every 3 second, the unit turn off power to outlet now, and the unit also activate PIR detect human motion
function. When somebody moves into the effective PIR area, the unit will turn power on to outlet at once. The key will illuminate in
green.
PIR:
Distances: 15 feet (max.), horizontal angle: 40 degree (max.), vertical angle: 70 degree (max.).
Detecting Somebody Motion
Standby Function Enable
 Change Screen
Power ON
PIR Function Enable
 Change Screen
$
CO2Meter
$
CO2Meter
(PIR icon Flash)
(Green LED Flash every 3 second)
-
-

Standby power, Delay off time and PIR sensor detecting distances setting:
Standby power: Off, 0.1W to 3289W.
Off power delayed time: 10 seconds to 2 hours.
PIR sensor detecting distances: Off (shunt down PIR function), 1 foot to 15 feet.
〈Flash Screen〉
Press
Enter
Hold Meter
〈Flash Screen〉
Key3sec
Press
Enter
Press
Enter
〈Change Screen〉
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
〈Flash Screen〉
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
EnterYES NO
-
+
EnterYES NO
-
+
EnterYES NO
-
+
EnterYES NO
-
+
〈Flash Screen〉
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
EnterYES NO
-
+
Press
Enter
〈Change Screen〉
Year
CO2
Rate
W
Kwh
$
CO2
$
Month
Lb
Kg
Total Day
Elap
Meter
h
ms
W
A
SAVE
m
Time V
Hr
SAVE
EnterYES NO
-
+
Press Key +0.1 W
Range
OFF, 0.1 ~ 3289 Watt
Press Key -0.1 W
1, Upper LCD display 12.5W is the unit standby off power level,
is automatically measured the standby power of appliance and
up a certain percentage when first time install the unit, normally it
shall be larger than the instant standby power of appliance.
2, it is adjustable, if user feel 12.5W standby off power level is
bigger or smaller. If user adjust this standby off power level down
to lower than appliance’s instant standby power (< 10.6W), the
unit always on, LED always green of on/off key.
3, Off = shunt down standby power comparative function, the
unit always on, LED always green of on/off key.
+
-
Lower LCD display 10.6W is appliance’s instant standby power
now.
Press Key
Next time
item
Select Range
10,20,30,40,50sec;
01 ~ 59 min;
01, 02 hour
Back time
item
+
1, Default is 30 minutes.
2, Shorter off power delayed time, save more energy, but
AC power on/off will be more frequently. Appropriate setting
off power delayed time will be balance to use appliances
and save energy, 1 hour or 2 hours for office, 30 minutes for
home, is our suggestion.
Press Key
Select Range
Sensitivity
OFF, 1-15 Ft
Press Key Next time
item
Back time
item
OFF = shunt down PIR function, the
unit will off power according to
Standby off power level and off
power delayed time conditions only.
After off power delayed time setting
value, the unit will be off power when
appliance on standby condition, LED
flash in green light every 3 second,
and the unit will not activate PIR
detect human motion function and
will not turn on power again even
somebody move into PIR effective
area. Do not recommend to off PIR
function.
Default is 15 feet.
+
-
Press Key
-

Retained measurements:
1. When power to the unit is interrupted, cumulative power consumption KWH, Elapsed Time, Cost, and CO2 will be retained
automatically into EEPROM. All user setting, Rate, Standby power, Off power delay time, PIR distances are already retained in
EEPROM on every time user setting, it is great advantage for user to set one time only and don’t worry about AC line power is
interrupted.
2. When the AC power line back or the unit plug into another outlet again, cumulative power consumption KWH, Elapsed Time, Cost,
CO2, Rate, Standby power, Off power delay time, and PIR distances will be retrieved automatically.
Specification:
Item Specification Accuracy Response Time
Range Res. Typ Max Action Recovery
Voltage 207 ~ 253 Volt 0.1V 0.5% 1% 1sec
Current 0.00~13.00 Amp 0.01A 0.5% 1% ± 0.1A 1sec
Active power 0.0~99.9 Watt 0.1W 1% 2% ± 5W 1sec
100~3289 Watt 1W 2% ± 5W
KWH 0.00~99.99 KWH 0.01KWH 1% 2% ± 5W 1sec
100~9999 KWH 1KWH
Elapsed Time 00:00~59:59 1sec 30 ppm 1 sec00:00~99:59 1min
100~9999 1hour
Cost ($)
Total/Day/Month/Year 0.00~99.99 0.01
1% 2% ± 5W 1sec
100~9999 1
Saved ($)
Total/Day/Month/Year 0.00~99.99 0.01
1% 2% ± 5W 1sec
100~9999 1
Cost Rate 0.000~9.999 0.001 --- --- ---
Kg-CO2 or Lb-CO2
Total/Day/Month/Year 0.000~9.999 0.01
1% 2% ± 5W 1sec
100~9999 1
Kg-CO2 Rate 0.000~9.999 0.001 --- --- ---
Kg  Lb 1 Kg = 2.2046 Lbs --- --- --- ---
1 Lb = 0.45359 Kg
Outlet 1--- --- --- ---
Output status LED Output ON：Green
Output OFF：Red --- --- --- ---
Standby Off Power
Level Set OFF, 0.1~99.9 Watt 0.1W
--- --- ---
100~3289 Watt 1W
Delay Time Set 10,20,30,40,50 sec 1 ~ 59, min
1, 2 hour
Spike free switch Spike free switch --- --- --- ---
ENVIRONMENT CONDITIONS GENERAL SPECIFICATION
IN DOOR USE ONLY Power Rating 230 Vrms ± 10%，50/60Hz
ALTITUDE : UP TO 2000M Power
Consumption Max. 0.8Watt; Standby: 0.4W
OPERATION TEMPERATURE : 0℃~ 50℃, Max. R.H. 90%
NON OPERATION TEMPERATURE : -10 ~ 60 Max.R.H. 95%℃℃ Ratings 13Amp〈3289Watts〉，Resistive and Inductive
OPERATION VOLTAGE IS LIMITED TO ±10% OF LINE VOLTAGE L/W/H L135mm x W63mm x H68mm (Outlet Unit +
Display/PIR unit)
POLLUTION DEGREE : 2
CAT II Weight Around 258g
Maintenance
Protect the meter from adverse weather conditions. The
meter is not waterproof. Do not expose the LCD display to
direct sunlight for long periods of time.
CAUTION: To avoid damage to the meter, do not expose it to
sprays, liquids, or solvents.
Clean the exterior of the meter by removing dust with a
lint-free cloth.
Use care to avoid scratching the clear plastic display filter.
For further cleaning, use a soft cloth or paper towel
dampened with water. You can use a 75% isopropyl alcohol
solution for more efficient cleaning.
CAUTION: To avoid damage to the surface of the meter, do
not use abrasive or chemical cleaning agents.
PRODIGIT ELECTRONICS CO.LTD.
8F, NO 88, Baojhong Rd., Sindian Dist.,
New Taipei City 23144, Taiwan, R.O.C
TEL : [phone]
FAX : [phone]
E-MAIL : [e-mail]
http://www.prodigit.com.tw