Morris MFS-16216 User manual

1
STAND FAN
OPERATING INSTRUCTIONS
FOR MODELS: MFS-16216 / MFS-16217
READ THESE INSTRUCTIONS CAREFULLY AND STORE THEM FOR FUTURE REFERENCE!

2
SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the followings:
1. To prevent fire or shock hazard, DO NOT expose this appliance to rain or moisture.
2. Dangerous high voltages are present inside this enclosure. To avoid electric shock,
DO NOT open the cabinet, refer servicing to qualified personnel only.
3. This appliance is intended for household use only and not for commercial,
industrial or outdoor use. Other use not recommended may cause fire, electric
shock or injury.
4. Ensure the fan is not placed near drapes,curtains, or any objects that may be
drawn into the fan.
5. To protect against fire, electrical shock and injury to persons, do not immerse the
unit, plug or cord in water or spray it with liquids.
6. The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the product.
7. No naked flames sources, such as candles, should be placed on the product.
8. Ventilation should not be impeded by covering the ventilation openings. Slots and
opening are provided for ventilation to ensure reliable operation of the product
and to protect it from overheating.
9. Care required with the use of this apparatus in tropical climates. Do not use the
appliance to temperatures over 40 °C.
10. Place the fan on a stable level and dry surface when operating to avoid
overturning.
11. Only connect to a suitably AC 220-240V~50Hz mains socket.
12. Do not operate the fan in the presence of explosive and/ or flammable fumes. Do
not place the fan or any parts near an open flame, cooking or other heating
appliance.
13. Do not operate the fan with a damaged cord or plug, after a malfunction or if it is
dropped or damaged in any manner.
14. Do not operate the fan without the fan grilles properly in place.
15. Do not place the fan close to an open window. Rain splashing on the fan could
cause an electric shock hazard.
16. Do not let the power cord hang over the edge of a table or counter or let it touch
any hot surfaces.
17. Do not insert or allow foreign objects to enter the grille openings as this may
cause damage to the appliance.
18. Do not use the fan if grille becomes damaged or loose.
19. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
21. Switch the fan OFF and unplug it from the outlet when it is not in use, when
moving fan from one location to another and before cleaning.

3
22. To disconnect, grip the plug and pull it from the wall outlet. Never pull by the
cord.
23. Do not attempt to repair, disassemble or modify the appliance. There are no
user-serviceable parts inside. Refer all servicing to qualified service personnel.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
MODEL NO
RATED VOLTAGE
RATED POWER
Noise
MFS-16216/
MFS-16217
220-240V~50HZ
60W
≤67dB(A)
STRUCTURE AND PARTS

4
ASSEMBLE INSTRUCTIONS
The fan is packaged with its foundation and other parts unattached. You must attach
them before operating the fan.
WARNING: Never operate the fan, without its foundation and other parts attached. Fan
should operate only in upright position; any other position could create a hazardous
situation.
Assemble sequence of the foundation and other parts as follow:
1. Unpack the fan and remove all parts from the package.
2. Use the bend bolt and the press plate provided, to attach the stand post parts
onto the base.
3. Adjust the lift pole to the desired height, and then lock it with the locknut for
lifting.
4. Loose the locknut on the switch box and insert the lift pole into the hole located
on the bottom of the switch box, then fasten the locknut back tightly.
5. Take off the motor shaft cover
from the fan head, and revolve the
triangle screw off. Then take off
the blade tie on the back grill, put
the grill back, ensuring that
locating pegs are engaged
correctly in the three holes of the
grill. Then, tighten the triangle
screw counterclockwise.
6. Push the big fan blade onto the
notch, until it is stuck on the
stopper pin of the motor shaft, and
then tighten the small fan blade
counterclockwise.
7. To attach the front grill to the back grill, use carefully the grill ring to hold them

5
together and fasten the grill ring with the screw provided.
INSTRUCTIONS FOR USE
Before using the fan make sure that it is on a flat and stable surface. Damage may occur
if it is placed on inclined surface.
Set all switches to OFF position, and then insert the plug directly into a standard AC
socket-outlet. Make certain that the plug fits tightly into the outlet.
a. Press the ON/OFF button to start the fan and select the fan speed level by pressing
SPEED button. Each time you press SPEED button, SPEED level changes as per the
following sequence: 1 2 3 4 5 6 1
Speed selection is circulated and the speed pilot lamp will be on, during the fan’s
operation.
b. Press MODE button to choose your desired wind mode. Each time you press the button,
mode changes as per the following sequence:
Normal wind nature wind sleeping wind normal wind
Wind mode selection is circulated and wind mode pilot lamp will be on during the fan’s
operation.
c. Set the time by pressing TIMER button to select for how many hours you want to set
the timer. The available range is 1~15 hours. The pilot light corresponding to the selected
hours will be illuminated. If you want to set 5 hours, you set 4 hours + 1 hour.
d. Press OSC button to select whether you need oscillation or not. Each time you press
the button oscillation changes, as per the following sequence:
Oscillation no oscillation oscillation
Press ON/OFF button to turn off the fan and all pilot lights will be switched off.
Note: all above functions can be set with the remote control using the corresponding
buttons (ON/OFF, MODE, TIMER, OSC) and +, - .
MAINTENANCE
Always turn off the fan and remove the plug from the socket-outlet before
cleaning.
Clean the external surfaces of the fan with a soft damp (not dripping wet) cloth.
WARNING:
Do not immerse the fan in water.
Do not use any cleaning chemicals such as detergents and abrasives.
Do not allow the interior (special for the PCB) to get wet as this could create a
hazardous situation.
When the unit is not in use, make sure that it is unplugged from the wall socket. To
store the fan, you may pack it in the original carton and store it in a cool and dry
place until later use.
In case of malfunction or doubt, do not try to repair the fan yourself; it may result
in a fire hazard or electric shock.

6
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials
and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life,
should be disposed of separately from your household waste. Please
dispose of this equipment at your local community waste collection/
recycling centre.
In the European Union there are separate collection systems for used electrical and
electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the requirements
of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at www.morris.gr
Exclusive importer in Greece:
Amiridis –Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki –Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr
www.morris.gr