Progress Lighting Springer P260004 User manual

PACKAGE CONTENTS
HARDWARE CONTENTS (not actual size)
Missing parts? Please contact Customer Service at 1-800-447-0573 or
[e-mail], 8am-8pm (Eastern), Monday - Friday
93165614 Page:1
PART DESCRIPTION QUANTITY
A Light Kit 1
P260004
B Lamps
2-LT SPRINGER FAN LIGHT KIT
AA
A
B
Qty:4
Screw
Qty:4
BB
Cage Screw
C1 Glass Shade
C
AA
BB
2

1
93165614 Page:2
!Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with
N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE
PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE.
KEEP THESE INSTALLATION INSTRUCTIONS
Preparation
1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing
or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Assembly Instructions
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive
cleaners or cleaners that contain alcohol.
1a. Remove the Decorative Cover (D) on the fan
by twisting it counterclockwise and then pulling
down.
1b. Identify the Mounting Plate (E) on the fan
that the Decorative Cover (D) was attached to.
Remove the three fan screws from the Mounting
Plate (E). Remove Mounting Plate (E)
completely. Mounting Plate (E) must be taken
off the fan in order to install the light kit.
Remove Fan Parts
FAN SCREWS
E
1a
1b
FAN
D
Mounting Plate (E)

ASSEMBLY INSTRUCTIONS
93165614 Page:3
22a. Loosen Screws (AA) and remove Light Kit Pan (F)
from the light kit.
2b. Use the three fan screws removed in step 1b to
attach the Light Kit Pan (F) to the fan.
2b
2c. Connect the Fan Wire Connector (G) to the Light
Kit Wire Connector (J).
Install Light Kit
F
2a
X4
Screws
AA
FAN SCREWS
FAN
F
2c
FAN
F
G
FAN SCREWS
AA
J
LIGHT KIT

ASSEMBLY INSTRUCTIONS
93165614 Page:3
2d 2d. Use Screws (AA) to attach the Light kit Housing
(H) onto the Light Kit Pan (F).
2f.Slide the GLASS SHADE (C) into the CAGE (I).
Tighten the Cage SCREW (BB) until the CAGE (I) is
secured to the Light kit Housing (H) .
2e
2f
2e. Screw Lamps (B) into the lamp sockets. Make
sure the Lamps (B) do not exceed the maximum
wattage specified on the fixture’s wattage rating label.
FAN
X4
Screws
AA
X4
Cage Screws
BB
AA
H
LIGHT
KIT
F
B
C
BB
I
H

PAGE of SPEC.NO.
disjoncteur central avant de commencer l'installation.
MISE EN GARDE: Lire les instructions avec soin et couper le courant au
del cortacircuitos principal antes de iniciar la instalación.
PRECAUCIÓN: Lea cuidadosamente las instrucciones y desconecte la electricidad
Instructions d'Assemblage et Installation
Instrucciones de ensamblaje e instalación
44 93124726
MISE EN GARDE: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer l'installation.
MISE EN GARDE: Risque d'incendie. Min 90°C conducteurs d'alimentation. Consulter un électricien qualifié pour assurer le
bon conducteur de circuit de dérivation.
AVERTISSEMENT - S'il y a d'autres mécanismes régulateurs qui s'emploient avec ce dispositif, suivre soigneusement
les instructions pour satisfaire aux exigences NEC. Si vous avez des questions, consulter un électricien qualifié.
MISE EN GARDE - Le verre est toujours fragile; maniez le(s) composant(s) et/ou l' (les) ampoule(s) avec prudence.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI
CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
CONSERVEZ CES INSTRUCTIONS D'INSTALLATION
PRECAUCIÓN: Lea cuidadosamente las instrucciones y desconecte la electricidad del cortacircuitos principal antes de iniciar
la instalación.
PRECAUCIÓN: Riesgo de fuego. Min. 90°C los cables de suministro. Consulte a un electricista calificado para asegurarse
de que el conductor del circuito derivado correcto. 
ADVERTENCIA - Si usa algún dispositivo especial de control con este aparato de luz, siga las instrucciones
cuidadosamente para asegurar la completa conformidad con los requisitos N.E.C. Si existe alguna duda, contacte un
electricista calificado.
PRECAUCION - El vidrio es frágil; tenga cuidado al manipular el (los) elemento(s) de vidrio y/o la(s) bombilla(s).
ESTE PRODUCTOR DEBE SER INSTALADO SEGUN EL CODIGO DE INSTALACION APLICABLE POR UNA PERSONA
QUE CONOZCA LA CONSTUSSION Y EL FUNCIONAMIENTO DEL PRODUCTO Y LOS RIESGOS QUE SUPONE.
GUARDE ESTAS INSTRUCCIONES DE INSTALACIÓN

93165614
REVISION TRACKING HISTORY
REV DESCRIPTION INIT.DATE ECN
A RELEASE FOR PRODUCTION BRR04/14/23 2304008