PROGRESSIVE DESK Corner Ryzer FLT-05 User manual

V 3.02
Scan for video assembly!
Corner Ryzer (FLT-05)
Table Lift and Table Top User Manual

Caution 3
Specifications
4
Components 5
Assembly 6
Table Top Installation 9
Dimensional Drawing 12
Reset Procedure 13
Operations 13
Troubleshooting 16
P a g e | 2
Table of Contents
Have any queries? Our expert engineers are here to help!
[email protected] progressivedesk.com
1-800-828-9414

Caution
Have any queries? Our expert engineers are here to help!
[email protected] progressivedesk.com
1-800-828-9414
P a g e | 3

Specifications
P a g e | 4
Input Voltage
Specification Description
120 VAC, 60 Hz
330 lbs (110 lbs per Leg)
1.57"/sec
23.6"
49.1"
23.6"
10% (2 Minutes On, 18 Minutes Off)
Yes
Stell
Program Up to 4 Memory Presets3, USB Charging Port
IP51 Legs and IP20 Controller
97.30 lbs
UL (Customizable)
15 Years
Force
Speed1
Install Size Retracted
Install Size Extended
Foot Length
Duty Cycle
Collision Detection2
Frame Material
Remote Functions
Protection Class
Unit Weight
Certifications
Limited Warranty
1Soft Start and Stop
Feature Description
The table lift will modulate movement when starting and stopping to ensure
smooth travel.
The table lift will stop movement and briefly move in the opposite direction if
an obstruction is detected. Refer to Collision Detection Sensitivity in
Operations section to configure.
The wired remote has the ability to save preset height locations for convenience.
Refer to Memory Presets in Operations section.
Note: Not available in all remote models.
Remote LED height display will turn off when left idle for 10 seconds.
Note: Not available in all remote models.
2Collision Detection
3Memory Presets
Low Power Mode

P a g e | 5
Components

55
3
2
15
P a g e | 6
Assembly
On the protected surface of your floor, lay your table top facing down. Orient it according to Step 1. The table lift assembly
process can be done directly on the table top surface as if you were building the table lift upside down.
Note: Some table tops are reversible. Take care to orient them according to features like pre-drilled holes and grommet
holes.

P a g e | 7
Assembly
STEP 6

P a g e | 8
Assembly
7
8
7
8
For Progressive Desk 30" wide table tops, use Holes 4 to 7. For Progressive Desk DT-90 Corner table top, use
holes 3 to 6.
14

P a g e | 9
Table Top Installation
2.5"- 3.0" 2.5"- 3.0"
2.5"- 3.0"2.5"- 3.0"
2.5"- 3.0"
2.5"- 3.0"
Move the table lift frame components to desired final position on top of the upside-down table top. Use a pencil to
mark the twelve table top mounting hole locations. Remove the table lift frame from the table top.
To assist in installation of the table top once it is right side up, you will need to create pilot holes. Install M5x20
Wood Screws (12) on the marked locations. Install only 1/4 of screw's length and then remove the screws.
Optional: An electric drill with a drill bit may be used to create pilot holes instead of the wood screws.
Place Progressive Desk DT-90 corner table top in accordance to the suggested dimensions in the diagram for
best fitment.

P a g e | 10
Table Top Installation

P a g e | 11
Table Top Installation

P a g e | 12
Dimensional Drawing
23.6"

1234 M
1
2
3
4
M
P a g e | 13
Operations

P a g e | 14
Operations

P a g e | 15
Operations

P a g e | 16
Troubleshooting
Have any queries? Our expert engineers are here to help!
[email protected] progressivedesk.com
1-800-828-9414