Progressive PA-TW-E7-M User manual

x4
x1
x1x1
ABC
D
ab
c
0.86"/sec
32°F-104°F
100-240VAC
E F
Table cover size:
Please do not exceed the maximum
load capacity.
WARNING
Input Voltage
Max Speed
Operational Temperature
Power Adapter Power Cable
No. Desk Converter Frame No.
No. Cable Management No.
Keyboard Tray No. Adhesive Buckle
No.
TOOLS
Only use the sit stand desk on top of flat and stable surface,
strong enough to support the product and any equipment
placed on top of it.
Hang the keyboard tray arms (a) on the
desk converter mounts (b) indicated
below and then tighten both levers (c).
12.1"
27.5"
14.75"
34.6"
16.3"
34.6"
Max: 55lbs
Max: 6lbs
+
4.9" - 19.9"
3$7:(0
55lbs
10%(Continuous operation for 2 min, rest for 18 min.
4.9"-19.9"
Maximum Load Capacity
Height Range
Duty Cycle
37.4"
24.2"
STEP 2
STEP 1
x1x1
Remove desk converter from
packaging and place it on the table.
Attention
Please place the product properly
according to it's size.
When removing the keyboard tray, release
the levers completely before removing the
keyboard tray.
Have any queries?
Our expert engineers are here to help!
Progressivedesk.com
[email protected]
1-800-828-9414

2
1
1
CAUTION
DO NOT place hands on or near support bars.
Pinch points are created during lifting and lowering
the desk converter. Failure to follow these
instructions may result in serious injury or damage.
Connect power
adapter and cable
Please make sure all installed equipment are
centered on the table, and not hanging off of
the edge or it may cause injury or damage.
Careful
Cable
Adhesive buckle helps to make the
cables clean and organized. Please
leave enough length of all cables for
height adjustments, otherwise it may
cause unexpected damage or injury.
Cable Buckle
Peel and attach the adhesive
buckles to the underside of
the desk converter
Careful
Use the cable management
to guide and bundle the cables
1
How to use handswitch
●“▲”
●“▼”
Adjust the desk upwards
Adjust the desk downwards
Solution
Attention
1. Power supply: AC 100V-240V,50/60HZ
2. Operational Temperature: 0°C - 40°C
3. Unplug the power plug before cleaning, wipe the dust on surface with a damp
cloth when cleaning, be careful not to let moisture into the internal parts or
connectors.
4. The control box contains electronic components, metals, plastics, wires etc.
Please dispose of it in accordance with each country's environmental legislation.
5. Check carefully to ensure correct and complete assembly before using.
6. Please read all instructions before first use.
7. Keep children and pets away from desk converter due to moving components.
8. Slight noise caused by the belt or brake system. This will not have any effect
on the use or performance of the desk converter.
9. Do not use corrosive chemicals when cleaning the desk converter.
10. If the supply cord is damaged, please reach out to the manufacturer to get a
replacement.
11. Keep the original packaging in case to protect the desk converter when
transporting.
The following troubleshooting guide will help you detect and eliminate
any common issues or errors. If you face a problem not listed below,
please contact your supplier.
No response while pressing UP/
DOWN buttons after connecting
power.
Drifting (movement while
unpowered)
Overwork (Duty cycle: Max 2min
on / 18min off)
1.Ensure all the cables are secure
2. Contact your supplier or dealer
1.Check if overloaded, max load:55 lbs
2.Contact your supplier or dealer
1.Resume use after resting for 30 minutes
2.Contact your supplier or dealer
Place devices and accessories
onto the desk converter carefully.
STEP 3
STEP 4
STEP 5
Raise
Lower
Buttons
Problem
Troubleshooting
Warning
Please do not put hands near the
supporting bars, as they change during
adjustments and may cause injury.
Please leave enough length
of cable for height adjustment.
Attention
Please transport by using two
people to prevent injury or
damage damage.
Attention