Progressive A592-52 User manual

AC
AD
1 OF 3
MADE IN MALAYSIA
Place all wooden parts on a clean and smooth surface such
as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing
straps before you start to assemble.
Do not tighten all screws / bolts until all completely assembled.
Keep all hardware parts out of reach of children.
I M P O R T A N T N O T E :
ASSEMBLY INSTRUCTION
Model No : A592-52 CONSOLE TABLE
REMARKS : YOU WILL ALSO NEED A PHILIP SCREW DRIVER
(NOT PROVIDED)
Description : DINING TABLE
A592-52
D862-10
1 PC
QTY/PCS
DINING TABLE
DESCRIPTION
1
NO
PART LIST
1 PC LEG FRAME LEFT
1 PC
1
2
QTY/PCS
TABLE TOP
DESCRIPTIONNO
PART LIST
D
B
A
SPRING WASHER M6
FLAT WASHER M6 x 13mm
ALLEN KEY M4 x 60mm
NO DESCRIPTION
JCBC BOLT M6 x 35mm
HARDWARE LIST
1 PC
18 PCS
18 PCS
18 PCS
QTY/PCS
C
3 LEG FRAME RIGHT 1 PC
STEP 1 STEP 2
STEP 3 STEP 4
REMOVE DRAWER FROM TABLE TOP
PLEASE REFER TO ASSEMBLY INSTRUCTION
FOR DRAWER REMOVAL & REINSTALL
REINSTALL DRAWER TO TABLE TOP
PLEASE REFER TO ASSEMBLY INSTRUCTION
FOR DRAWER REMOVAL & REINSTALL.
COMPLETE ASSEMBLE
4 TABLE BASE 1 PC
4x
TOP SUPPORT 5 2 PCS
10x
1
3
A
C
B
D
2
D
BC
A
5

Y
AA
AB
AE
AF
AG
2 OF 3
MADE IN MALAYSIA
ASSEMBLY INSTRUCTION
Model No : A592-52 CONSOLE TABLE
REMARKS : YOU WILL ALSO NEED A PHILIP SCREW DRIVER (NOT PROVIDED)
DINING TABLE
A592-52
D862-10
1 PC
QTY/PCS
DINING TABLE
DESCRIPTION
1
NO
PART LIST
STEP 5 STEP 6
STEP 7 STEP 8
STEP 9
COMPLETE ASSEMBLE
REASSEMBLE HANDLE FROM
INSIDE TO OUTSIDE POSITION
2x
2x
REASSEMBLE HANDLE
FROM INSIDE TO
OUTSIDE POSITION
C
A
B
D
CB
A
D
4

R
T
U
V
W
3 OF 3
MADE IN MALAYSIA
ASSEMBLY INSTRUCTION
Model No : A592-52 CONSOLE TABLE
REMARKS : YOU WILL ALSO NEED A PHILIP SCREW DRIVER (NOT PROVIDED)
DINING TABLE
A592-52
D862-10
1 PC
QTY/PCS
DINING TABLE
DESCRIPTION
1
NO
PART LIST
TO REMOVE DRAWER:
STEP 1 : EXTEND THE BOX DRAWER TO ITS FULL EXTENSION.
STEP 2 : LOCATE THE DRAWER SLIDE LOCK ON EACH SIDE OF THE DRAWER BOX.
PULL UP THE LOCK ON THE LEFT SIDE OF THE DRAWER BOX AND PUSH DOWN
THE LOCK ON THE RIGHT SIDE OF THE DRAWER BOX IN THE SAME TIME AND
PULL DRAWER STRAIGHT OUT UNTIL SLIDE DRAWER MEMBERS DISENGAGE
FROM CABINET MEMBERS.
STEP 3 : REMOVE THE DRAWER.
ASSEMBLY INSTRUCTIONS FOR DRAWER REMOVAL AND REINSTALL
TO REINSTALL DRAWER :
MAKE SURE THE DRAWER WILL BE RE-INSTALL TO ITS ORIGINAL POSITION.
STEP 1 : INSERT DRAWER BY PULLING TRACK ON THE LEFT AND RIGHT CABINET MEMBERS
ALL THE WAY FORWARD (INCLUDING BALL BEARING RACK)
STEP 2 : ALIGN TRACKS ON DRAWER WITH SLIDERS AND PUSH IN THE DRAWER
UNTIL THERE IS AUDIBLE "CLICK" SOUND.
STEP 3 : CHECK FOR PROPER ALIGNMENT BY INSPECTING DRAWER FRONT MARGINS
FOR SPACING AND SQUARENESS.
OPEN AND CLOSE SLOWLY SEVERAL TIMES TO ENSURE THE PROPER INSTALLMENT.
IF THERE IS ANY UNEVEN, PLEASE REPEAT STEP OF REMOVAL AND REINSTALL THE DRAWER.
PUSH DOWN
STEP 1
STEP 2 PULL UP
STEP 3
STEP 1
STEP 1 STEP 1
Lock
Left side view
Lock
Right side view
Bearing