Prolon M2000 SERIES Installation instructions

HARDWARE GUIDE
Heatpump Controller M2000 Series
Specifications and Operational Guide
REV. 7.3.0
PL-HRDW-HP-M2000-C/F-EN
www.proloncontrols.com |[e-mail]
17 510, rue Charles, Suite 100, Mirabel, QC, J7J 1X9

2
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Table of Contents
General Information ....................................................................................................................................................... 4
PL-M2000 Heatpump Controller ...................................................................................................................................................................4
Description............................................................................................................................................................................................................4
General Behavior ................................................................................................................................................................................................4
Operating Sequence .........................................................................................................................................................................................5
General...................................................................................................................................................................................................................5
Occupied Mode...................................................................................................................................................................................................5
Unoccupied Mode..............................................................................................................................................................................................5
Components .................................................................................................................................................................... 6
Component Identication...............................................................................................................................................................................6
LEDs and Switches..............................................................................................................................................................................................7
HAND/OFF/AUTO Switches .............................................................................................................................................................................8
Jumpers..................................................................................................................................................................................................................8
Input and Output Identication....................................................................................................................................................................9
Addressing Dipswitch Conguration for Network Communication............................................................................................. 10
Inputs .............................................................................................................................................................................11
Temperature Sensors ......................................................................................................................................................................................11
Room Sensors ....................................................................................................................................................................................................12
Proof of Fan.........................................................................................................................................................................................................12
Dry Contact for Clogged Filter or Schedule Override .........................................................................................................................13
Dry Contact for Alarm Signal........................................................................................................................................................................13
Static Pressure and CO................................................................................................................................................................................. 
Outputs .......................................................................................................................................................................... 15
Output Specications .....................................................................................................................................................................................15
Typical Connection of Triac Outputs 1 to 5............................................................................................................................................ 16
Typical Connection of Analog Outputs 1 to 3....................................................................................................................................... 16
Power Source & Network...............................................................................................................................................17
Power Source .....................................................................................................................................................................................................17
Network Communication..............................................................................................................................................................................17
Technical Specications ............................................................................................................................................... 18
Compliance .................................................................................................................................................................... 19
FCC User Information ......................................................................................................................................................................................19
Industry Canada ...............................................................................................................................................................................................19
Overall Dimensions....................................................................................................................................................... 20

3
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Table of Figures
Figure 1 - Component Identication..................................................................................................................................................................6
Figure 2 - LEDs Identication................................................................................................................................................................................7
Figure 3 - Location of the EXTERNAL jumpers...............................................................................................................................................8
Figure 4 - Location of the INTERNAL jumpers.................................................................................................................................................8
Figure 5 - INT and NET jumpers ...........................................................................................................................................................................8
Figure 6 - AI jumpers................................................................................................................................................................................................8
Figure 7 - Input and Output Identication.......................................................................................................................................................9
Figure 8 - RJ45 Pinout..............................................................................................................................................................................................9
Figure 9 - Addressing Dipswitch....................................................................................................................................................................... 10
Figure 10 - Connecting the Temperature Sensors.......................................................................................................................................11
Figure 11 - Typical Wiring of the PL-RS Room Sensor to the Controller...............................................................................................12
Figure 12 - Connecting the Proof of Fan Contact to the Controller......................................................................................................12
Figure 13 - Connecting the Dry Contact Input to the Controller...........................................................................................................13
Figure 14 - Connecting the Alarm Contact to the Controller ..................................................................................................................13
Figure 15 - Connecting the CO and Pressure Sensors ............................................................................................................................ 
Figure 16 - Connecting of Digital Outputs 3 and 4 .................................................................................................................................... 16
Figure 17 - Connecting Analog Output 1 (External Power) .................................................................................................................... 16
Figure 18 - Connecting the 24VAC Power Source........................................................................................................................................17
Figure 19 - Connecting to the Network...........................................................................................................................................................17
Figure 20 - M2000 Size Diagram....................................................................................................................................................................... 20

4
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
General Information
Description
The Prolon PL-M2000 Heatpump controller is a microprocessor-based controller designed to operate residential or
commercial heatpump equipment. It uses PI (Proportional-Integral) control loops and acts as a master when used on a
network with Prolon zone controllers.
The Standalone model of this controller will not act as a master to other Prolon zone controllers, relying instead on the
demand provided by a local sensor.
General Behavior
Although fully congurable, the Prolon M2000 Heatpump controller uses pre-established control sequences or ’’proles’’
to operate specic HVAC equipment with dedicated output functions. These can be fully optimized to obtain the best
results for each type of system. Numerous parameters enable the modication or ne tuning of the fan, the compressor
outputs, the action of the heating outputs (On-or-O / pulsed / modulating), the bypass or VFD, outside air dampers,
CO2 levels, the proportional bands, integration times, dierentials, operational ranges, setpoints and a whole range of
limits and safeguards. The various programming options also allow the user to modify the schedule, unoccupied mode
settings, morning warm-up and supply air pre-heating sequences as well as the network demand control strategy best
suited for the building space it is controlling. All these parameters can be accessed by using the
Prolon Focus software.
PL-M2000 Heatpump Controller

5
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Operating Sequence
General
The Prolon M2000 Heatpump controller receives readings from three dierent temperature sensors: outside air, return
air and supply air. It operates on a congurable schedule using an internal real-time clock. Also, as a Master device, it
receives data from the zone controllers sent on the network bus. The controller then analyzes all the data and demands
sent by the zones and commands the appropriate outputs to respond accordingly, within parameters set by the tempe-
rature sensors and other safety limits. The Master sends back information on its network such as supply air temperature,
occupancy status and other relevant data for the zone controllers to use.
Occupied Mode
The controller operates the fan. When there is a cooling demand from the zones, the Heatpump controller will put the
reversing valve into cooling mode and activate the compressor outputs as long as all temperature limits, delays and
other related parameters are respected. Once the demand is satised, the outputs are deactivated within the prescribed
minimum on/o time delays.
When there is a heating demand from the zones and the outside temperature is above the low balance point, the
Heatpump controller will put the reversing valve into heating mode and activate the compressor outputs as long as all
temperature limits, delays and other related parameters are respected. If the outside temperature is below the low
balance point, the controller will activate the auxiliary heating outputs. If the heatpump is congured for water-to-air
mode, the low balance point is ignored and the use of compressors is permitted all year round. Protection sequences are
in place that will activate auxiliary heat upon failure of the compressors. Once the demand is satised, the outputs are
deactivated within the prescribed minimum on/o time delays.
When there is no cooling or heating demand from the zones, only the fan is enabled. If the heating equipment permits,
a supply air pre-heating sequence may be enabled. This allows cold mixed air to be heated to a more comfortable level
for subsequent use by the zones for ventilation.
Unoccupied Mode
The fan can be congured to operate in intermittent mode. When there is a cooling or heating demand from any single
zone, the Rooftop controller will activate the fan and the necessary cooling or heating outputs as long as all temperature
limits, delays and other related parameter are respected. Once the demand is satised, the fan and any cooling/heating
outputs are deactivated within the minimum on/o time delays set.
During the unoccupied period, the Rooftop controller can be driven by the highest demand on the network and will
operate the fan and relevant outputs accordingly.

6
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Components
Figure 1 - Component Identification
Component Identification
Legend:
A- Addressing Dipswitch
B- AUTO/OFF/HAND Switches
C- RS485 INT port for interface communication (RJ45 plug and screw connectors are in parallel)
D- Analog outputs (3)
E- Digital outputs (5)
F- Analog inputs (9)
G- RS485 NET port for network communication
H- Terminal block for 24VAC (Class 2 transformer)
I - Jumpers for terminating and bias resistors for the INT port
J - Jumpers for terminating and bias resistors for the NET port

7
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
LEDs and Switches
The M2000 has various LEDs which are linked to dierent functions and outputs of the controller. Each LED is individually
identied to help the user make a quick visual diagnostic of the controller’s activity and status.
LED Descriptions
•24 VAC: The M2000 is receiving 24 VAC from the power
source.
•5V DC: The microchip and other components on the
M2000 are being powered successfully by a 5VDC
source derived from the 24VAC source.
•HBEAT: When this LED is blinking, the microchip is
active and the controller’s program is running (normal).
When this LED is ON and steady, the M2000 is inactive
and the microchip is awaiting programming (you must
use Prolon’s Focus software to reprogram the microchip).
•STAT: Reserved.
•NETSND: Indicates the transmission of data onto the
network communication bus.
•NETREC: Indicates reception of data from the network
communication bus.
•INTSND: Indicates the transmission of data onto the
interface communication bus.
•INTREC: Indicates the reception of data from the inter-
face communication bus.
•AO3: The intensity of the LED represents the voltage
present on analog output 3.
•AO2: The intensity of the LED represents the voltage
present on analog output 2.
•AO1: The intensity of the LED represents the voltage
present on analog output 1.
•DO5: Represents the activity of digital output 5.
•DO4: Represents the activity of digital output 4.
•DO3: Represents the activity of digital output 3.
•DO2: Represents the activity of digital output 2.
•DO1: Represents the activity of digital output 1.
Figure 2 - LEDs Identification
AO 3
AO 2
AO 1
DO 5
DO 4
DO 3
DO 2
DO 1
INTSND
INTREC
NETSND
NETREC
24VAC
5VDC
HBEAT
STAT

8
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
HAND/OFF/AUTO Switches
Jumpers
Each output on the M2000 has a dedicated switch that lets the user manually override the activity of the output. “HAND”
mode (switch at rightmost position) fully activates the output (24 VAC for digital outputs, 10VDC for analog outputs).
“OFF” (switch at center) deactivates the output and “AUTO” (switch at left) returns control of the output to the program
in the M2000’s microchip.
The M2000 has jumpers that are externally accessible (see Figure 3), as well as jumpers that are on the lower internal
board (see Figure 4), that allow for conguration of various hardware elements.
• INT: These are the jumpers for the bias and terminating resistors used for the interface communication bus. See the
Prolon network guide for information about bias and terminating resistors. (See Figure 5)
• NET: These are the jumpers for the bias and terminating resistors used for the network communication bus. See the
Prolon network guide for information about bias and terminating resistors. (See Figure 5)
• AI 1 - 9: These jumpers allow the user to select the signal mode of the associated analog input. (See Figure 6)
Figure 3 - Location of the EXTERNAL jumpers
Figure 5 - INT and NET jumpers
Figure 4 - Location of the INTERNAL jumpers
Figure 6 - AI jumpers
INT
NET
AI9
AI8
AI7
AI6
AI5
AI4
AI3
AI2
AI1
Jumper AI
0-5 volts 4-20 mA THERMISTOR

9
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Input and Output Identification
All the inputs and outputs of the M2000 use pluggable screw type terminal blocks with elevator style clamping, which
make connections easier and more secure.
For incoming communication from a remote computer or network controller, dual RJ45 type connectors are available in
parallel with screw type terminal blocks. The RJ45 connectors allow the use of premade CAT5 cables for simple plug-and-
play RS485 communication. These RJ45 connectors follow the Modbus pinout specication for RS485 communication.
Figure 7 - Input and Output Identification
Figure 8 - RJ45 Pinout
24
VAC
Bottom row:
common for all outputs
Bottom Row:
common for all inputs
AO3 - Bypass / VSD
AO2 - Economizer
AO1 - Preheating / Mod. Heat
DO5 - Aux Heat
DO4 - Rev Valve
DO3 - Compressor 2 (Y2)
DO2 - Compressor 1 (Y1)
DO1 - Fan (G)
HPS
INT Port: Prolon
digital temperature
sensor
- OR -
Incoming RS485
network
communication
(Modbus)
HP
Incoming
communication
from remote
computer
- OR -
Network Controller
(dual RJ45 and
terminal blocks)
Static pressure (0-5 / 1-5V) (1 / 1.5 / 2 / 2.5 in)
Ext dry contact for alarm /
CO2 sensor (4-20 mA) (0-2000 ppm)
External dry contact for proof of fan
Zone temperature setpoint (0-10K potentiometer)
Zone temperature sensor (10K thermistor)
Supply air temperature sensor (10K thermistor)
Return air temperature sensor (10K thermistor)
Outside air temperature sensor (10K thermistor)
Supply water temp sensor (10K thermistor)
Controller’s power source
Unit’s R&C terminals (24VAC)
Dry contact for clogged filter / Dry contact for
schedule override / Supply water temp (10k therm)
HPS
Net Port: Prolon digital
temperature sensor
- OR -
Incoming RS485 network
communication (Modbus)
HP
Outgoing RS485
network
communication
(modbus)
(to zones)

10
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Addressing Dipswitch Configuration for Network Communication
For proper communication, a unique address must be congured on each controller by setting the rst 7 switches on the
addressing dipswitch to the desired value.
These switches are numbered from 1 to 7 and represent a binary value from 1 to 64 (1, 2, 4, 8, 16, 32, and 64 respectively).
The last switch (#8) is reserved. The value of each switch that is in the ON position is added together to form the numeri-
cal address of the controller.
The example in Figure 9 shows the switches 1, 2 and 4 in the ON position. Therefore, the corresponding values are 1, 2
and 8, giving an address sum of 11.
The Prolon network allows a maximum of 127 addresses; therefore 127 controllers.
Figure 9 - Addressing Dipswitch

11
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Inputs
Temperature Sensors
Figure 10 - Connecting the Temperature Sensors
The M2000 Heatpump controller has analog inputs that can monitor supply and return air temperatures, as well as
another that can monitor either the outside air or supply water temperature (water-to-air mode only, see gure 10) and
will integrate these readings into its control sequence.
Alternatively, the supply air temperature can be retrieved from a zone controller that has its own supply sensor and
belongs to the M2000’s network.
The outside air temperature can be also be provided by an alternate source. If a network controller is present on the
network, it can retrieve the outside temperature reading from one controller and distribute it to any other controllers on
the network.
Outside air sensor
-OR-
Supply water
temperature
Return air
temperature
Supply air
temperature

12
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Room Sensors
Proof of Fan
The M2000 can receive the setpoint and temperature from a specic room when a PL-RS analog thermostat is connected
to it. The M2000 will then automatically integrate this information into its control sequence. The setpoint may also simply
be set by software. The PL-RS series room sensors are connected using a 3-conductor cable (see Figure 11).
The M2000 has an analog input dedicated to the proof of fan signal. Please refer to Figure 12 to see how to correctly
connect it to analog input 7. To indicate proof of fan, the contact must be closed. If no proof of fan signal is available, you
must short analog input 7, or else the controller will interpret the absence of signal as a fan malfunction and no heating
or cooling action will be taken.
Figure 12 - Connecting the Proof of Fan Contact to the Controller
Figure 11 - Typical Wiring of the PL-RS Room Sensor to the Controller
Proof of Fan
PL-RS Room Sensor
Jumper from 1 to 3

13
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Dry Contact for Clogged Filter or Schedule Override
Dry Contact for Alarm Signal
Analog input 4 on the M2000 can also be congured as a dry contact input for either a clogged lter sensor or as a schedule
override input. Please refer to Figure 13 to see proper connection.
• Clogged lter sensor: To indicate that the lter is clogged, the contact must be closed.
• Schedule Override: Closing the contact causes the M2000 to immediately return to occupied mode from unoc-
cupied mode. The M2000 remains in occupied mode as long as the contact is held closed. If it was already in occu-
pied mode, there is no change.
The M2000 has an analog input which can be designated as an alarm signal input. Please refer to Figure 14 to see how
to correctly connect it to analog input 8. To signal an alarm, the contact must be closed. Closing this contact will prevent
the use of the compressors, either in heating or cooling. Auxiliary heating will still activate as required.
Figure 14 - Connecting the Alarm Contact to the Controller
Figure 13 - Connecting the Dry Contact Input to the Controller
Clogged
Filter
or
Schedule
Override
Alarm

14
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Static Pressure and CO
Analog inputs 8 and 9 on the M2000 heatpump controller are dedicated to the CO2 and static pressure sensors, respec-
tively. By default, a 4-20 mA signal is expected for the CO2 input and a 0-5 VDC or 1-5 VDC signal is expected for the static
pressure input. However, this can be modied using the internal jumpers (see p.8). Please refer to Figure 15 for correct
wiring.
Figure 15 - Connecting the CO and Pressure Sensors
CO2 Sensor
Static Pressure Sensor
(-)
(+)
(-)
(+)

15
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Outputs
Output Specifications
The M2000 Heatpump controller contains 8 customizable outputs; ve triac ON/OFF outputs (24VAC) and three analog
outputs (0-10VDC). Output conguration is performed via the Prolon Focus software.
An integrated resettable fuse protects each of the outputs of the M2000 against current surges and short circuits. This
protection will cut the current to the output as soon as an overload condition is detected. The fuse is a round, yellow-
coloured PTC that will change to orange and heat up on an overload condition. Once power has been removed from the
M2000, the fuse will cool down and automatically reset. Fix the faulty wiring and you will be able to activate the output
once again.
Output Type Action Application
DO 1 Triac source 24VAC,
Max Current: 300 mA On-or-O Fan (G)
DO 2 Triac source 24VAC,
Max Current: 300 mA On-or-O Compressor (1st Stage) (Y1)
DO 3 Triac source 24VAC,
Max Current: 300 mA On-or-O Compressor (2nd Stage) (Y2)
DO 4 Triac source 24VAC,
Max Current: 300 mA On-or-O Reversing Valve
DO 5 Triac source 24VAC,
Max Current: 300 mA On-or-O Auxiliary Heat
AO 1
Congurable Analog Output:
- 0 to 10 VDC
- 2 to 10 VDC
- 0 to 5 VDC
Max Current: 40 mA
Modulating Proportional/
Plused/
On-or-O
Preheating Only/
Preheat + Heating/
Heating
AO 2
Congurable Analog Output:
- 0 to 10 VDC
- 2 to 10 VDC
Max Current: 40 mA
Modulating Proportional Economizer
AO 3
Congurable Analog Output:
- 0 to 10 VDC
- 2 to 10 VDC
Max Current: 40 mA
Modulating Proportional Bypass/
Variable Frequency Drive

16
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Typical Connection of Triac Outputs 1 to 5
Typical Connection of Analog Outputs 1 to 3
On the M2000 Heatpump controller, all triac outputs produce a 24 VAC live voltage when activated. Note that all output
voltages originate from a single voltage supply: the equipment’s transformer. Consequentially, only the live side of the
output connections are usually needed; these are on the top row (see gure 16). The bottom row is the common (GND).
For all analog outputs, the common is found on the bottom row terminal blocks, and the active signals are found on the
top row terminal blocks (see Figure 17). Analog outputs 1 can be congured to modulate a 0-10 VDC load, to pulse a 0
or 10 VDC triac relay or to control a 10 VDC On/O relay. Analog outputs 2 and 3 can only modulate a DC load (0-10 VDC
or 2-10 VDC).
Figure 17 - Connecting Analog Output 1 (External Power)
Figure 16 - Connecting of Digital Outputs 3 and 4
(+)
(-)
External Load
SSR
(W1)
Equipment Terminal Board
(Y2)

17
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Power Source & Network
Power Source
Network Communication
The M2000 controller is powered by the HVAC equipment’s 24 VAC Class 2 power supply by connecting the common
(’’C’’ wire) to the "COM" terminal block and the live (‘’R’’ wire) to the "24 VAC" terminal block (see Figure 18). The common
for all inputs and outputs is the same as the power source’s common. All output power sources also originate from the
HVAC equipment’s power source.
The Prolon M2000 Heatpump controller is designed to work with the Prolon zone controllers (except Heatpump
Standalone controller). When they are networked, the M2000 and zone controllers all communicate in real-time. The
network connections are made using the network terminal block located on the M2000 controller (see Figure 19).
Figure 18 - Connecting the 24VAC Power Source
Figure 19 - Connecting to the Network
( R )
( C )
To HVAC Equipment Terminal (Class 2)
24VAC
( A )
( B )
Towards
RS485
Network

18
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Technical Specifications
Supply: 24 VAC ±10%, 50/60 Hz, Class 2
Power: 5 VA (consumption), 40 VA (Input)
Inputs: 9 congurable analog inputs (thermistor / dry contact / 4-20mA / 0-5 VDC)
Digital Outputs: 9 congurable analog inputs (outside temperature / return / supply / zone / water supply / dry contact
for clogged lter / schedule override / proof of fan / alarm, room setpoint, static pressure). Input signals (thermistor / dry
contact / 4-20mA / 0-5 VDC) individually congurable for each input
Analog Outputs: 3 x 0-10 VDC outputs, 40 mA max
Indication lights (LED): State of each output / Communication / Power / State of microprocessor
Microprocessor: PIC18F6722, 8 bits, 40 MHz, 128KB FLASH memory
Communication (HP): Modbus RTU (RS485) or BACnet MS/TP (RS485), up to 127 nodes
Communication (HPS): Modbus RTU (RS485), up to 127 nodes
Baud Rates: 9600, 19200, 38400, 57600, 76800, 115200
Connection: Removable screw-type terminal blocks (max 16 AWG) and RJ45 modular jacks
Dimensions: 5.39" x 4.41" x 2.25" (137 mm x 112 mm x 57 mm)
Weights: 1.05 lbs (0.48 kg)
Environment: -4 to 122 ºF (-20 to 50 ºC) Non-Condensing
Certication: UL916 Energy Management Equipment, CAN/CSA-C22.2, RoHS, FCC part 15: 2012 class B
The performance specications are nominal and conform to acceptable industry standards. Prolon Inc. will not be liable for
damages resulting from misapplication or misuse of its products.

19
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Compliance
• cULus Listed; UL 916 Energy Management Equipment, File E364757, Vol.1
• CAN/CSA-C22.2 No. 2015-12, Signal Equipment
• FCC Compliant to CFR47, Part 15, Subpart B, Class B
• Industry Canada (IC) Compliant to ICES-003, Issue 5: CAN ICES-3 (B)/NMB-3(B)
• RoHS Directive (2002/95/EC)
FCC User Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Any changes or modications not approved by Prolon can void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada
This Class (B) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment regulations.
Cet appareil numérique de la Classe (B) respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.

20
REV. 7.3.0 / PL-HRDW-HP-M2000-C/F-EN
Overall Dimensions
REV. 7.3.0
PL-HRDW-HP-M2000-C/F-EN
4.41"
(112 mm)
5.39"
(137 mm)
2.29"
(58 mm)
Figure 20 - M2000 Size Diagram
12345678
© Copyright 2021 Prolon. All rights reserved.
No part of this document may be photocopied or reproduced by any means, or translated to another language without prior written
consent of Prolon. All specications are nominal and may change as design improvements are introduced. Prolon shall not be liable for
damages resulting from misapplication or misuse of its products. All trademarks are the property of their respective owners.