Prolux LED FOLLOW 350 User manual

http://prolux.net.ua
1
LED FOLLOW 350
USER MANUAL
1. NTRODUCTION

http://prolux.net.ua
2
Thank you for having chosen a led follow spot 350 You will see you have acquired a powerful
and versatile device.
Unpack your led follow spot 350
Delivery includes
Mounting holder 1 pc
Power wire 1pc
USER MANUAL 1pc
2. DESCRIPTION OF THE DEVICE
2.1. Profile
With the idea of energy saving and environment protection, the device uses lower power loss
and extremely high efficiency led. The device housing cover is made of used the new high
strength heat resistance engineering plastics, with beautiful shape and smooth lines. The
designing and manufacturing is in compliance with the IEC standard. The device is suitable in
the large-scale theatrical performance, the theater, the performance hall, the bar, night club
and so on.
2.2. Overview
2.3. SPECIFICATION
Lamp: Led350W, high brightness LED, brightness is more than 1500w discharge lamp
Color temperature: 8000-8500K,
Lifetime of led, more than 50000hours
Luminous flux :20000lm - 240001m
Power supply: AC100V-240V, 50Hz/60Hz
Power consumption: 450W
Color wheel 5colors + open white
CTO wheel: 3200K, 4500k, 5600K
Manual focus
Strobe 1-20 flash per second.
N.W.: 9.9kgs
G.W.: 11.5kgs
Dimensions (LxWxH): 660x295x270mm
2.4. Photographic chart

http://prolux.net.ua
3
2.5. Safety warning
Every person involved with the installation, operation and maintenance of this device
must be qualified
User must follow the instructions of this manual
Unqualified person cannot open the housing cover and operate the device, or the
dealer will not accept liability for any resulting defects or problems.
The device against rain and moisture
Power supply: AC100V-240V/50HZ-60HZ
Make sure the power switch is off, the power plug, outlet and the earth connection are
in well condition before connecting the device with the mains.
Please use qualified power plug and outlet. Never connect the power cord of this device
with other electrical equipment.
During move and installation, make sure the device not crashed with metal parts and
other tough materials.
Always disconnect from the mains, when the device is on installation and dismantled
The minimum distance between light-output and the illuminated surface must be more
than 50cm.
The device must only be installed on a non-flammable surface. In order to safeguard
sufficient ventilation, leave 50 cm of free space around the device. Please note that
heat-sensitive objects may be deformed or damaged by the emitted heat.
During the operation the housing becomes very hot! Do not operate the device for 15
minutes after switching off.
The maximum ambient temperature Ta = 45°C must never be exceeded. The maximum
housing temperature Tb = 60°C must never be exceeded.
For indoors use.
Replace any visible cracked protective shield, filters and lens.
The protective shield, filters and lens will require weekly cleaning as smoke fluid tends
to build up residues, reducing the light output very quickly.
3. INSTALLATION
3.1. Installation
When installation, keep the device far away the heat sensitive objects and explosives
sensitive objects, leave at least 50CM of free space around the device.
When install devices, please first fix the mounting holder on the device, as shown in the
figure.

http://prolux.net.ua
4
Then put the device on the stand, make sure that the stand must be placed on the
ground smoothly, and tighten all the fasteners.
2.Connection with mains
The person involved with the power connection must be qualified and has the electrical
engineering certificate.
Connect the device to the mains with the power plug.
The earth should be connected.
Power consumption 450W, input power supplyAC100V-240V, 50/60Flz.
Please use qualified stand, and make sure the stand can withstand more than ten times
the weight of device.
3.2. Connection with mains
The person involved with the power connection must be qualified, and has the electrical
engineering certificate.
Connect the device to the mains with the power plug.
The earth must be connected.
Power consumption 450W, input power supplyAC100V-240V, 50/60Flz
3.3. Replacing fuse
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the
housing (anti-clockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
3.4. Focus
The objective lens cylinder is usually shrink before leaving factory, after connect the

http://prolux.net.ua
5
projector to the mains, user may lose the screws and pull out the lens cylinder, till the
white light output circular is clearly presented, locking tightly the two screws again.
When the projection distance is changed, user can follow previous operating steps, and
focus the projector.
4. OPERATION
APPENDIX
Problem and solution
Problem
Reason
Resolution
Device not
work
No power
AC100V-240V,50HZ/60HZ
Check the power connection,and
Make sure device connect the mains in well
condition.
Check if switch is on
Check if the fuse is good
LED bulb is
off
LED bulb damaged
Replacing led bulb
LED driver board damaged
Replacing led driver board
Temperature swtich
damaged
Replacing temperature switch
Fans not work
Fans damaged
Replacing fans
Caution:
Unqualified person involved with installation, operation and maintenance of this device is
prohibited.
If any above-mentioned problem happened, or unknown problem happened, please
contact manufactory or distributor for assistance.