ProMediaGear Katana GK User manual

Thank you for purchasing the ProMediaGear Katana Heavy Duty Gimbal Head.
The GK, Katana Gimbal was designed to effectively balance your telephoto lens
and camera for horizontal and vertical panning. Our robust design, featuring precision
engineering will allow effortless control of your lens. Shoot with condence.
#GK Specications:
Length............................................................................ 10.50 inches (267mm)
Width.....................................3 inches (76mm) 4.30 inches (109mm) with knob
Height .................................................................................13 inches (330mm)
Weight............................................................................... 5.58 pounds / 2531g
Load Capacity...................................................................... 150 pounds / 68 kg
Tripod Mount....................................................................................................... 3/8-16
16555 108th Ave, Orland Park, IL 60467 USA
1-708- 263-4443 • Toll Free: 1 -888- 413-3332 • www.ProMediaGear.com
#GK, Katana Gimbal Head

Setup:
1. To mount the GK Katana onto a tripod begin by rotating the Base Plate (G) clockwise
on the 3/8 inch mounting screw of the tripod. Next, lock the pan knob (F) then using the
leverage from the GK Katana, tighten a bit more until snug.
2. Open the Arca Compatible Clamp (C) by loosening the Clamp Knob (D) and insert
you lens/camera plate onto clamp. Lock Clamp Knob (D) securely.
Balancing Camera/Lens:
3. While holding the camera and lens with a light touch loosen Tilt Lock Knob (A) so the
arm is free to swing and also slightly loosening Clamp Knob (D). Now you will be able
to slide your camera and lens plate forward or backward in the clamp unitl the lens is
perfectly horizontal and not drooping. Once neutral balance is found remember to lock
the Clamp Knob (D) securely. You may also set your resistance on Tilt Lock Knob (A)
a. If the Lens is pointing DOWN, loosen the Clamp knob (D) and move camera/lens
backwards. Set resistance on Tilt Lock Knob (A) when complete.
b. If the Lens is pointing UP, slightly loosen the Clamp Knob (D) and move camera/
lens forward. Set resistance on Tilt Lock Knob (A) when complete.
4. After balancing your lens you may set the vertical position to allow the lens to stay
pointed wherever you aim in a perfect balanced nodal position if desired. Start by
loosening the Vertical Arm Clamp Knob (E) and raising the clamp up or down to find
the proper balance point. This is typically achieved when the center of the tilt bearing is
even with the center of your lens barrell. When done correctly the lens will stay at any
position you point it to without drooping and remain properly balanced on your gimbal.
Find the position that best fits your shooting style. Happy Shooting!
Instructions
F. Pan Lock Knob
G. Base Plate
A. Tilt Lock Knob
E. Cradle Clamp Knob
D. Clamp Knob
C. Arca Compatible Clamp
B. Arca Compatible Vertical Arm

Features
• Smooth pan and tilt locking mechanism ( separate from assembly mounts )
• Arca compatible lens mount
• CNC Precision Machined from T6061 aluminum
• Sealed Ball Bearings
• Hard anodized scratch resistant finish
• Made in USA
• 5-year warranty
Maintenance
Check before every use for any loose screws/parts and tighten with knob or
supplied hardware. The bearings are sealed and require no lubrication.
A small amount of oil (WD40 or similar) may be used on the knobs if necessary.
Caution should be taken that it is not exposed to potentially corrosive environments.
Taking these precautions will greatly extend the life of the product.
34mm and 42mm
Pro-Stix Tripods
#GF2
Flash Doubler
Accessories
#GKJr.
Katana Junior Gimbal
#HM1
Monopod Tilt Head
#SS2P3
Strap Adapter
#BH1
Ball Head
#PX4
4.5" Lens Balance Plate
#PX6
6" Lens Balance Plate
#PXC2
Arca Rail w/ Clamp

16555 108th Ave, Orland Park, IL 60467
1-708- 263-4443 • Toll Free: 1- 888 -413-3332 • www.ProMediaGear.com
rev 0918