Propel Trampolines PIVOT User manual

OPERATION
MANUAL
FOR
PIVOT

QUICK NAVIGATION
CONTENTS
PIVOT COMPONENTS
PRE-RIDE CHECKLIST
POWER ON/OFF
REMOTE CONTROL
CHANGING WHEELS
1
2
3
4
6
NOTE
ALL PICTURES ARE FOR ILLUSTRATION AND ILLUSTRATION ONLY.
DIFFERENT SERIES OF PIVOT PRODUCTS MAY DIFFER IN APPEAR-
ANCE AND MATERIAL. PLEASE REFER TO THE ACTUAL PRODUCT.

1. HEADLIGHT(OPTIONAL)
2. FRONT BADGE
3. PULL BAR(OPTIONAL)
4. DECK
5. TAIL LIGHT
6. BELT GUARD
7. MOTOR
8. AT WHEEL
9. PU WHEEL
10. DKP TRUCK
11. INTERNAL ACCESS
PANEL/HEAT SINK
12. CHARGING PORT
13. POWER BUTTON
14. BUSHING
15. BELT
16. MOTOR PROTECTION BRACKET
PIVOT COMPONENTS

CHECK WHETHER THE PARTS ARE DEFORMED OR WORN.
CHECK WHETHER THE SCREWS ARE LOOSE BEFORE USE AND OFTEN
THROUGHOUT OWNERSHIP.
AFTER THE SKATEBOARD IS STARTED, CHECK FOR ABNORMAL SOUNDS.
DO NOT USE IT UNTIL THE CAUSE OF THE ABNORMAL SOUND IS FOUND
AND RESOLVED.
CHECK BOTH THE FRONT AND REAR TRUCKS AND THAT ALL FOUR
WHEELS ARE SECURE.
BE SURE TO MAINTAIN YOUR TIRE PRESSURE.
PROPERLY SECURE YOUR HELMET AND PROTECTIVE PADS.
MAKE SURE YOUR BOARD AND REMOTE BATTERIES ARE FULLY CHARGED.
READ THE SAFETY INSTRUCTIONS IN THE PACKAGE CAREFULLY AND
FOLLOW IT.
PRE-RIDE CHECKLIST
BEFORE EACH RIDE, INSPECT YOUR BOARD AND REMOTE
FOR DAMAGE. DO NOT RIDE IF DAMAGED.

PUSH THE BOARD TO START
A FANTASTIC RIDE
POWER ON: The power button is a self-reset switch, which is
installed at the bottom of the PIVOT, close to the motor side.
POWER OFF: Press the power button or leave the skateboard
stationary for 5 minutes, and the skateboard will automatically
turn off.
ROLLING START: This board is equipped with “rolling start”
which means you can shove/push the board ahead and once it
has reached a speed that is over 5km/h it will turn itself on (You
will hear a beep).
POWER ON/OFF

REMOTE CONTROL

The cruise control function is an advanced function.
Please use it with caution before you are familiar with it. Please do not per-
form special actions during the cruise control. Please end the cruise control
function before you need to change gears or perform other operations.
1. Begin with the board and the remote turned off.
2. Turn on the board by depressing the power button, and release. The power
button should illuminate.
3. Depress power button again and hold for 5-7 seconds utill it begins flash-
ing, depress. The flashing power button means it’s ready to pair.
4. Turn on remote.
5. Press both buttons for 1 second, simultaneously, release. (You'll see the
battery meter populate)
6. Board is now paired.
REMOTE PAIRING
Push the wheel forward to accelerate, and push the wheel backward to slow
down.
REMOTE FUNCTIONS
NOTE
(1) Scroll wheel
During acceleration, short press the power button once to switch to the cruise
mode. Pull the acceleration/deceleration wheel to end the cruise state. In the
constant speed cruising state, if the skateboard and the remote control are dis-
connected, the skateboard will stop slowly.
(2) Cruise control
The remote control will vibrate in the following two situations:
▪When the skateboard battery is less than 25%.
▪When the remote control fails to connect to the skateboard.
Note: The safe wireless control distance between the remote control and
the skateboard is 2 meters.
(3) Vibration

CHANGING WHEELS
NOTE: PIVOT's default wheel size and gear ratio are
pre-calculated for you to make wheel changing easier and
simpler. Our stock PU wheel and AT wheel can share the
same configuration, so you don't need to adjust the position
of the motor or any parameters within the remote.
The wheel replacement of PIVOT 2-IN-1 is very simple.
1. Loosen the bolt next to the wheel.
2. Take the wheel and gear out.
3. Install the new wheel.
4. Tighten the nut.
AT WHEEL
STREET WHEEL
For other third party wheel options please consult the third party wheel manufacturer,
check their adaptation tables, check our accessory store, or send an email to
ser[email protected] with any question you may have. We are here to help.
NOTE