Prorack K698 Operation and installation manual

K698
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
x 4 x 4 x 8 x 8
Revision No: 3B 1

Fitting Kit K698
MAX kgs (lbs)
W/P WHD
Hyundai
i30 Tourer, 5dr Wagon 13-17 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
i30, 5dr Estate 13-17 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
i30, 5dr Wagon 13-17 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K698
X
A B C 1 2 3
i30 Tourer, 5dr Wagon 13-17 (AU) -180mm 620mm - 862mm 808mm -
-7 -1/16ths" 24 7/16ths" - 33 15/16ths" 31 13/16ths" -
i30, 5dr Estate 13-17 (EU) -180mm 620mm - 862mm 808mm -
-7 -1/16ths" 24 7/16ths" - 33 15/16ths" 31 13/16ths" -
i30, 5dr Wagon 13-17 (NZ) -180mm 620mm - 862mm 808mm -
-7 -1/16ths" 24 7/16ths" - 33 15/16ths" 31 13/16ths" -
3

Fitting Kit EN
K698
Items you will require:
●12mm Socket
13mm Socket
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
4

Fitting Kit EN
K698
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K698
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
6

Fitting Kit EN
K698
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Assemble foot from kit into leg.
7

Fitting Kit EN
K698
●Insert pins through foot into leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
●Refer to the top side of the pad for the part
number.
8

Fitting Kit EN
K698
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 13-04-244A
B = 13-04-245A
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
Fitment
●Open or remove fixed-point covers.
9

Fitting Kit EN
K698
●Locate stud with the nut attached.
●Using a 12mm socket, remove existing nut.
●Install bracket ensuring the short leg sits
over the existing nut position.
10