Prorack K927 User manual

K927
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 2 x 1
x 4 x 4 x 1 x 4
x 2 x 2
Revision No: 2B 1

Fitting Kit K927
MAX kgs (lbs)
W/P WHD
Mitsubishi
Triton Club Cab, 4dr Ute Apr 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Triton Club Cab, 4dr Ute Apr 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Triton Double Cab, 4dr Ute Apr 15-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
Triton Double Cab, 4dr Ute Apr 15-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
2

Fitting Kit K927
X
A B C 1 2 3
Triton Club Cab, 4dr Ute Apr 15-+ (AU) -240mm 300mm - 877mm 818mm -
-9 -7/16ths" 11 13/16ths" - 34 1/2ths" 32 3/16ths" -
Triton Club Cab, 4dr Ute Apr 15-+ (NZ) -240mm 300mm - 877mm 818mm -
-9 -7/16ths" 11 13/16ths" - 34 1/2ths" 32 3/16ths" -
Triton Double Cab, 4dr Ute Apr 15-+ (AU) -275mm 525mm - 877mm 795mm -
-10 -13/16ths" 20 11/16ths" - 34 1/2ths" 31 5/16ths" -
Triton Double Cab, 4dr Ute Apr 15-+ (NZ) -275mm 525mm - 877mm 795mm -
-10 -13/16ths" 20 11/16ths" - 34 1/2ths" 31 5/16ths" -
3

Fitting Kit EN
K927
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K927
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5

Fitting Kit EN
K927
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K927
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
7

Fitting Kit EN
K927
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Use the following grubscrew lengths:
A = 70mm (2 3/4")
B = 55mm (2 1/8")
8

Fitting Kit EN
K927
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 218A
B = 295A
C = 296A
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
9

Fitting Kit EN
K927
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10