Prorack K947 User manual

K947
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4 x 1
x 4 x 8
Revision No: 3C 1

Fitting Kit K947
MAX kgs (lbs)
W/P WHD
Peugeot
Bipper, 5dr Van 08-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Fiat
Fiorino, 5dr Van 08-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Fiorino, 5dr Van 08-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Citroen
Nemo, 5dr Van 08-13 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K947
X
A B C 1 2 3
Bipper, 5dr Van 08-+ (EU) -250mm 510mm - 1010mm 957mm -
-9 -13/16ths" 20 1/16ths" - 39 3/4ths" 37 11/16ths" -
Fiorino, 5dr Van 08-+ (EU) -250mm 510mm - 1010mm 957mm -
-9 -13/16ths" 20 1/16ths" - 39 3/4ths" 37 11/16ths" -
Fiorino, 5dr Van 08-+ (ZA) -250mm 510mm - 1010mm 957mm -
-9 -13/16ths" 20 1/16ths" - 39 3/4ths" 37 11/16ths" -
Nemo, 5dr Van 08-13 (EU) -250mm 510mm - 1010mm 957mm -
-9 -13/16ths" 20 1/16ths" - 39 3/4ths" 37 11/16ths" -
3

Fitting Kit EN
K947
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K947
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K947
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
6

Fitting Kit EN
K947
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Assemble foot from kit into leg.
●Insert pins through foot into leg.
7

Fitting Kit EN
K947
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
Fitment
●Open or remove fixed-point covers.
●Select grubscrews and screw into the
vehicle's fixed points.
●Repeat for all four positions.
8

Fitting Kit EN
K947
●Apply transparent tape next to fixed point.
●Place crossbar foot over grubscrews.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
9

Fitting Kit EN
K947
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10