Prostat ESD check ESI-870 User manual

Operations Manual
Surface Resistance/Resistivity Indicator
ESI-870

Copyright 2001-2020 by ESD Check. All rights reserved. Printed in the United States of America. No
part of this manual may be used or reproduced in any manner whatsoever without written permission.
For information contact Prostat Corporation.
ESD Check is the registered trademark of PROSTATCorporation

ESI-870 Resistance/Resistivity Indicator
2
TABLE OF CONTENTS
ESD Check®ESI-870 RESISTANCE/RESISTIVITY INDICATOR
Title Page #
I. Before using the Instrument........................................................................................... 3
II. Safety.............................................................................................................................. 3
III. Description...................................................................................................................... 3
IV. Accuracy ......................................................................................................................... 4
V. Battery Installation & General Maintenance.................................................................... 5
VI. Reading the ESI-870 Scale............................................................................................. 7
VII. ESI-870 Operation Procedures..................................................................................... 11
VIII. Functionally Testing the ESI-870....................................................................................15
General Specifications.................................................................................................. 17

ESI-870 Resistance/Resistivity Indicator
3
Before using this, or any other electronic piece of equipment, carefully read the instruction
manual completely.
I. Before Using the Instrument
Examine the instrument for damage, contamination (excessive dirt, grease, etc.) and
defects. If any abnormal conditions exist, do not attempt to make any measurements.
II. Safety
A. The following safety information must be observed to insure maximum personal
safety during the operation of this meter.
1. DO NOT use the meter if the meter looks damaged, or if you suspect the
meter is not operating properly.
2. DO NOT touch the Brass Electrode Bars while operating this meter.
III. Description
The ESI-870 is an LED indicating, wide range resistance
measurement instrument with broad application flexibility. It
measures surface resistance in accordance with ESD Association
STM11.11, surface resistivity in accordance with ASTM D-257,
resistance to ground, and resistance point to point. This instrument
gives simple, repeatable measurements to indicate whether a
material is conductive, static dissipative or insulative. The ESI-870
employs parallel bar sensing and features an easy to read LED light
scale. The instrument may be used to measure a wide variety of
ESD materials, products and equipment.
A. Functions
The ESI-870 is designed to perform several functions accurately and conveniently.
1. Measures Surface Resistivity of Packaging materials in Ohms/Square per
Electronic Industries Association Packaging Standard EIA-541, in
accordance with test methods described in ASTM D-257.
2. Performs correlated measurements of Surface Resistance of Packaging
Materials in Ohms per ESD Association Standard ANSI/ESD STM11.11.
3. Makes general Point to Point Resistance and Resistance to Ground
measurements of Floors, Chairs, Carts, Worksurfaces, and other ESD
Controlled materials and products.

ESI-870 Resistance/Resistivity Indicator
4
B. Controls & Electrodes
1. The ESI-870 has one active control, a green "Press to Test" button on the
front panel of the instrument. This button performs two functions:
a. It turns the instrument ON, activating the test circuit and LED's.
b. It applies test voltage to the electrode(s) and auxiliary connections.
C. Indication & Resistance/Resistivity Scales
1. Eleven (11) LED's provide Resistance and Resistivity measurement
indication in one decade increments. (See Figure 1, below.)
a. Ten (10) LED's represent resistance or resistivity measurements.
b. One (1) LED is used to indicate when the measurement exceeds
normal testing range, and the range of the ESI-870.
2. The row of 10 LED's is labeled with
two scales. Both scales are
designed for packaging materials
measurement in accordance with
EIA-541 and ESD Association
standards, and correlate to ASTM
D-257 and ANSI/ESD STM11.11
measurement procedures.
a. The Upper Scale is labeled
forSurface Resistivity
measurements in Ohms/Square per ASTM D-257. While the ESI-
870 measurements are in keeping with ASTM D-257 bladed fixture
procedures, these measurements also correlate directly to ASTM D-
257 measurements made with a precision concentric ring fixture.
b. The Lower Scale is labeled for Surface Resistance
measurements in Ohms per ANSI/ESD STM11.11
standard. The ESI-870 measurements correlate directly to
ANSI/ESD STM11.11 measurements made with its defined, precision
concentric ring fixture. The ESI-870 does not reproduce the ANSI/ESD
STM11.11 procedure; it correlates to ANSI/ESD STM11.11 data.
IV. Accuracy
A. While the ESI-870 has an automatic resistance range feature, its accuracy is
dependent upon the following factors.

ESI-870 Resistance/Resistivity Indicator
5
1. For Surface Resistance/Resistivity measurements, the material under test
should be placed on an "insulated" surface for best accuracy.
2. The instrument must be fully positioned on the material being measured
and the electrode switch must be switched “ON”.
3. The instrument should be steadied by your fingers so that the full length of
each electrode is making even contact with the material under test.
4. Slight pressure must be applied when pressing the test button.
B. The design of the ESI-870 is based on automatic ranging across reference
resistors to provide simple indication of a material's resistance/resistivity.
1. The two machined brass Electrodes form a single "Square" for resistivity
measurements.
2. Overall Accuracy of the unit is ±10%.
3. The decade Changeover Point from one decade to another is based on
measured resistance; ±1/2 decade on logarithmic scale (i.e., 3.16 x 10n)
4. The accuracy of the Changeover Point is ±1/2 decade.
5. Instrument Resolution: is one order of magnitude.
V. Battery Installation & General Maintenance
A. Battery Installation
1. Power is supplied by a standard 9 volt battery. One battery will provide
approximately 40 hours of continuous operation.
2. Replace the battery whenever the unit will not perform an "Initial
Operational Check", described below, or when the unit has not been used
for several weeks or months.
3. To replace the battery, remove the battery cover on the back of the
instrument by applying pressure to the grid area marked with an arrow, and
sliding the panel towards the bottom end of the case.
4. Carefully disconnect the instrument
battery power connector from the
battery and discard the old battery in
manner appropriate for your locale.

ESI-870 Resistance/Resistivity Indicator
6
5. Connect a fresh battery to the instrument battery power connector and
insert the new battery into the case. Take care to position the battery
connector wires to allow the battery cover to close easily.
6. Replace the battery cover on the back of the meter by positioning it in the
guide grooves and sliding it forward carefully. Use the thumb of one hand
to maintain downward pressure on the cover and to keep it aligned. At the
same time, use the thumb of your other hand to apply pressure to the end
of the battery cover and slide it into its locked position.
a. Do not over force the cover closed. It should snap into its locked
position with firm, yet relatively gentle pressure.
b. If the cover does not easily lock closed, remove the cover and
battery. Reinsert it to obtain a better fit. Be sure connector wires
are positioned not to obstruct the battery compartment cover.
7. The ESI-870 is now ready for testing and use.
B. Initial Operational Check
Once the battery is installed in the ESI-870, check its initial function as follows.
Note that this procedure should be conducted each time the instrument is used,
and whenever the instrument's performance or battery function are in question.
1. Place the instrument, with electrodes down, on a clean metal surface such
as the PTB-915 Test Bed. Measure the resistance of the plate using the
"ESI-870 Operation Procedures" described below, i.e., Push the "Press to
Test" button and observe LED indication.
a. The Yellow LED located at
left end of the scale should
light, indicating a very
"conductive" material
measurement.
b. Proceed to Step 2, below.
c. If the lowest decade LED
(103UPPER Scale and 102
LOWER Scale) does not
light, the unit is not
functioning properly, or the
battery is dead.

ESI-870 Resistance/Resistivity Indicator
7
2. Place the instrument, with electrodes
down, on a clean plastic insulating
surface such as the white BOTTOM
surface of the PTB-915 Test Bed.
Measure the resistance of the plastic
sheet using the "ESI-870 Operation
Procedures" described below, i.e.,
Push the "Press to Test" button and
observe LED indication.
a. The Red LED located at right
end of the scale should light
briefly, then the Red center
panel "Insulative -- Exceeds
ESI-870 Range" LED should
light. This indicates a very high resistance "Insulative" material
measurement.
b. This completes the "Initial Operational Check"
c. If the highest decade LED "Insulative -- Exceeds ESI-870 Range"
does not light, the unit is not functioning properly, or the battery is
dead.
B. Cleaning
1. Periodically clean the electrodes and the instrument case area between
them with a soft, non-abrasive cloth, and a solution of 70% alcohol and
water.
2. Wipe the surface with a soft cloth moistened with clean alcohol and allow to
dry thoroughly.
3. Dust off any lint.
VI. Reading the ESI-870 Scale
The ESI-870 resistance measurement function features automatic ranging. It is designed
to provide four (4) kinds of measurements that may be read on two different
resistance/resistivity scales.
A. UPPER Scale Resistance
Measurement Functions
The UPPER scale is used in three (3)
measurement applications: Surface
Resistivity in Ohms/Square per ASTM
D-257, Resistance to Ground (Rtg)

ESI-870 Resistance/Resistivity Indicator
8
using the front panel Auxiliary Connection, and Resistance Point to Point (Rtt)
when using the two Resistance Reference Auxiliary Connections located on the top
end of the instrument.
1. When the ESI-870 is used to measure Surface Resistivity of a Packaging
Material in Ohms/Square per ASTM D-257, the bottom two brass
electrodes are firmly placed against the material, and ESI-870 actuated.
a. The resistance between the two electrodes is displayed on the
LED's and approximate surface resistivity in Ohms/Square is read
from the UPPER scale, above the LED's.
b. The color indication and scale notes describe the material's
approximate Static Control Classification in accordance with
Electronic Industries Association Packaging Standard, EIA-541, as
follows:
(1) The Yellow LED lights indicate the material is in the
"Conductive" range, i.e., less than 1.0x105Ohms/square.
(2) The Green LED lights indicate the material is in the "Static
Dissipative" range, i.e., greater than 1.0x105to less than
1.0x1012 Ohms/square.
(3) The Red LED lights indicate the material is "Insulative", or
greater than 1.0x1012 Ohms/square, and possibly greater
than the range of the ESI-870.
c. Note that when the instrument is used for Packaging Material
Surface Resistivity in Ohms/square as described above, the
equivalent Surface Resistance in accordance with ANSI/ESD
STM11.11 Standard is described on the LOWER Scale. See
"Surface Resistance in Ohms per ANSI/ESD STM11.11: The
LOWER Scale Resistance Measurement Function" below, for
further information.
2. When the ESI-870 is used to
measure Resistance of a
Surface to Ground (Rtg) Ohms,
the front panel "Auxiliary
Connection -- Resistance to
Ground" connection is used with
the provided six foot lead/phone
plug accessory.
a. The ESI-870 is placed on
the surface to be
measured to ground.

ESI-870 Resistance/Resistivity Indicator
9
b. The phono plug of the six foot lead is inserted in the front panel
"Auxiliary Connection".
c. The opposite end of the lead is connected to an ESD Ground
reference, and the ESI-870 is then actuated.
d. The resistance in Ohms between one electrode on the test
material's surface and the ground point is displayed on the UPPER
scale, above the LED's.
Note:The UPPER Scale unit of measure in this Rtg
measurement mode is Ohms, not Ohms/square.
e. The color indication and scale notes may, or may not describe the
material's Static Control Classification, depending on the material
being measured and the standard reference being used.
3. When the ESI-870 is used to measure Resistance between two points, i.e.,
Resistance Point to Point (Rtt) in Ohms, the two "Resistance Reference
Inputs & Auxiliary Connections" located at the top end of the unit are used
with additional test leads.
a. The additional test leads are inserted in the Auxiliary Connection
receptacles that are
designed for standard
banana plugs.
b. The opposite ends of the
test leads are connected
to the object to be
measured, i.e.,
equipment points, test
fixture, electrodes, etc.
c. The electrode switch is
moved to the
“ELECTRODES OFF”
position.
d. The ESI-870 is hand held, be careful not to touch the brass
electrodes, then the unit is actuated.
Important Note: If the brass electrodes are active when these two
Auxiliary Connections are used and body or material contact is
made with the brass electrodes during this measurement mode, the
indicated reading may be affected.

ESI-870 Resistance/Resistivity Indicator
10
e. The resistance in Ohms between the two lead connection points is
displayed on the UPPER scale, above the LED's.
Note:The UPPER Scale unit of measure in this Rtt
measurement mode is Ohms, not Ohms/square.
f. The color indication and scale notes may, or may not describe the
material's Static Control Classification, depending on the material or
equipment being measured and the standard reference being used.
B. Surface Resistance in Ohms per ANSI/ESD STM11.11: The LOWER Scale
Resistance Measurement Function
The LOWER scale is used in one (1) measurement application: Surface
Resistance of Packaging Materials in Ohms per ANSI/ESD STM11.11 Standard
test method. Note that the ESI-870 does not duplicate the ANSI/ESD STM11.11
measurement procedure. However, the measurement results correlate closely
with the S-11.11 data when compared under typical laboratory conditions.
1. When the ESI-870 is used to measure Surface Resistance of a Packaging
Material in Ohms per ANSI/ESD STM11.11, the bottom two brass
electrodes are firmly placed against the material, and ESI-870 actuated.
2. The resistance between the two electrodes are displayed on the LED's and
approximate surface resistance in Ohms per ANSI/ESD STM11.11 is read
from the LOWER scale, below the LED's.
3. The color indication and scale notes describe the material's approximate
Static Control Classification in accordance with Electronic Industries
Association Packaging Standard, EIA-541, as modified for ANSI/ESD
STM11.11 measurements.
a. The Yellow LED lights
indicate the material is
in the "Conductive"
range, i.e., less than
1.0x104Ohms.
b. The Green LED lights
indicate the material is
in the "Static
Dissipative" range, i.e.,
greater than 1.0x104to
less than 1.0x1011
Ohms.

ESI-870 Resistance/Resistivity Indicator
11
c. The Red LED lights indicate the material is "Insulative", or greater
than 1.0x1011 Ohms, and possibly greater than the range of the ESI-
870.
4. Note that when the instrument is used for Packaging Material Surface in
Ohms as described above, the equivalent Surface Resistivity in accordance
with ASTM D-257 in Ohms/Square is described on the UPPER Scale.
VII. ESI-870 Operation Procedures
Before each use, the ESI-870 should be tested using the Initial Operational Check,
previously described and reviewed below. However, one should practice the "Basic
Procedure for Making Surface Resistance/Resistivity Measurements" to become familiar --
and comfortable -- with the instrument before testing and use.
A. Basic Procedure for Making Surface Resistance/Resistivity Measurements
1. Place the material to be measured on an "insulative" surface, such as the
PTB-915 Test Bed. This test configuration offers the best accuracy.
a. This prevents incorporating a conductive test bed in the
measurement circuit.
b. If a conductive test bed is used, you may obtain a measurement
indication that is lower than the actual material resistance.
2. Place the ESI-870 on the surface to be measured, electrodes down against
the test material. Make sure the electrode switch is in the “ELECTRODES
ON” position.
Be careful not to place the instrument on blemished, bent or
wrinkled areas as this will affect the quality of your measurements.
3. Place your index finger at the
top edge of the instrument,
above the UPPER scale notes.
4. Place your thumb directly on the
Green "Press to Test" button.
5. Balance the weight of your
hand between the thumb and
index finger and press down
slightly on the unit while
pushing the "Press to Test"
button.

ESI-870 Resistance/Resistivity Indicator
12
a. Do not apply excessive pressure
b. Positioning your fingers in this manner will allow you to steady the
instrument and insure that the electrodes make full contact with the
material.
c. A measurement error of up to one order of magnitude may occur if
full contact is not made between the brass electrodes and the
material under test.
The ESI-870 will measure "high" in this situation because full
parallel resistance between the brass electrodes will not exist.
d. You will notice the LED's will light as they automatically range to a
final measurement
6. Continue applying steady pressure until one (1) LED remains on, indicating
a stable measurement. (Approximately 5 seconds)
7. Read the LED indication from either the UPPER or LOWER scale.
a. If using Surface Resistivity in Ohms/square per ASTM D-257 as
your measurement criteria, read the UPPER scale.
b. If using Surface Resistance in Ohms per ESD Association
ANSI/ESD STM11.11 as your measurement criteria, read the
LOWER scale.
B. Initial Operational Check: A Review
Prior to using the ESI-870 for test measurements always perform the Initial
Operational Check, as follows. This procedure assumes that a fresh battery of
good quality has been properly installed in the instrument.
1. Place the instrument, with electrodes down, on a clean metal surface such
as the PFP-861 Foot Plate and measure its resistance as described above.
a. The Yellow LED located at left end of the scale should light,
indicating a very "conductive" material measurement.
b. Proceed to Step 2, below.
c. If the lowest decade LED (103UPPER Scale and 102LOWER
Scale) does not light, the unit is not functioning properly, or the
battery is dead.
2. Place the instrument, with electrodes down, on a clean plastic insulating
surface such as the white BOTTOM surface of the PFP-861 Foot Plate, and
measure its resistance as described above.

ESI-870 Resistance/Resistivity Indicator
13
a. The Red LED located at right end of the scale should light briefly,
then the Red center panel "Insulative -- Exceeds ESI-870 Range"
LED should light. This indicates a very high resistance "Insulative"
material measurement.
b. This completes the "Initial Operational Check"
c. If the highest decade LED "Insulative -- Exceeds ESI-870 Range"
does not light, the unit isn’t functioning properly, the battery is dead.
C. Resistance to Ground (Rtg) Measurement Procedure
1. Insert the black lead 3.5mm
phone jack into the front panel
"Auxiliary Connection --
Resistance to Ground"
Note:By inserting the
lead into the auxiliary
connection, you have
disabled one of the ESI-
870's brass electrodes
2. Connect the opposite end of the
black lead to a defined ESD
Ground point. Use the
accessory alligator clip if necessary.
3. Place the ESI-870 on the material to be measured
4. Place your index finger at the top edge of the instrument, above the UPPER
scale notes.
5. Place your thumb directly on the Green "Press to Test" button.
6. Balance the weight of your hand between the thumb and index finger and
press down slightly on the unit while pushing the "Press to Test" button.
a. Do not apply excessive pressure
b. Positioning your fingers in this manner will allow you to steady the
instrument while insuring that the operational electrode is making
full contact with the material being measured.
c. You will notice the LED's will light as they automatically range to a
final measurement
7. Continue applying steady pressure until one (1) LED remains on, indicating
a stable measurement. (Approximately 5 seconds)

ESI-870 Resistance/Resistivity Indicator
14
8. Read the LED indication in Ohms from the UPPER scale.
D. Resistance Point to Point (Rtt) Measurement Procedure
When the ESI-870 is used to measure Resistance between two points, i.e.,
Resistance Point to Point (Rtt) in Ohms, the two "Resistance Reference Inputs &
Auxiliary Connections" located at the top end of the unit are used with additional
test leads.
1. Insert two banana plug equipped leads into the "Resistance Reference
Inputs & Auxiliary Connections" and place the electrode switch to the
“ELECTRODES OFF” position.
2. The opposite ends of the test leads are connected to the object to be
measured, i.e., equipment points, test fixture, electrodes, etc.
3. The ESI-870 is hand held, being careful not to touch the brass electrodes,
then push the "Press to Test" button.
a.Important Note: If you do not enable the “ELECTRODES OFF”
switch, the brass electrodes are active when these two Auxiliary
Connections are used. If body or material contact is made with the
brass electrodes during this measurement mode, the indicated
reading may be affected.
b. You will notice the LED's will light as they automatically range to a
final measurement
c. Continue pushing the "Press to Test" button until one (1) LED
remains on, indicating a stable measurement. (about 5 seconds)
4. The resistance in Ohms between the two lead connection points is read
from the UPPER scale, above the LED's.
Note:The UPPER Scale unit of measure in this Rtt measurement
mode is Ohms, not Ohms/square.
E. Other Resistance Measurements Using the ESI-870
As a basic resistance instrument, the ESI-870 can be used for general resistance
measurements of virtually any ESD Controlled product or material. To increase its
flexibility, one may employ fixtures, NFPA electrodes, extended leads, clips or
clamps for evaluating the following items.
Floors, Mats, Worksurfaces, Chairs, Carts, Body Resistance, Tapes, Conveyors,
Footwear, Assembly Equipment, Garments, Tools, Raw Materials, Production Aids,
Tote Boxes, Packaging Materials, and others.

ESI-870 Resistance/Resistivity Indicator
15
VIII. Functionally Testing the ESI-870
A. The ESI-870 has no internal parts to adjust, so verification of calibration can be
achievedusing the following process.
If verification cannot be achieved, the unit
should be returned to the supplier.
B. Using the Resistance reference inputs & Auxiliary
connections at the end of the unit, insert one lead into
each input jack and place the electrode switch to the
“ELECTRODES OFF” position.
C. Insert the opposite ends of the leads into a Resistance
Reference such as the PROSTAT®PAR-809C Variable
Resistance Reference
1. The range of the resistance reference required is
from >1.0x103to 1.0x1010 Ohms.
2. Measurements greater than 1010 are calculated
using cad generated techniques, as high
resistance’s greater than 1010 are difficult to verify
with a test voltage of 9 volts.
D. Once the leads are inserted, set the resistance reference
to the desired resistance, i.e. 103
1. Press and hold the ESI-870's "Press to Test"
button
Important Note: If you do not enable the
“ELECTRODES OFF” switch, the brass
electrodes are active when these two Auxiliary
Connections are used. If body or material
contact is made with the brass electrodes during
this measurement mode, the indicated reading
may be affected.
2. The 103LED (as read on the top scale) should
light
3. Repeat this process using all of the ranges possible with the resistance
reference
E. To measure the changeover point between decades:

ESI-870 Resistance/Resistivity Indicator
16
1. Gradually increase the resistance of the resistance reference while
pressing the test button
2. Record the resistance when the next LED lights and holds in a stable
manner. This is the changeover resistance.
Example: The first LED (103) is illuminated. At 4,000 Ohms the 104LED is
illuminated. The changeover point is 4.0x103Ohms.

ESI-870 Resistance/Resistivity Indicator
17
ESI-870 Resistance/Resistivity Indicator
Test Voltage & Current: Nominal 9 volts and 0.006 µA to 1.0 mA.
Power: One (1) standard 9-volt battery, PROCELL, Eveready #216
(NEDA 1604, JIS 006P, IEC 6F22)
Electrodes: 2 each Machined Brass, One (1) Square Resistivity configuration
Overall Accuracy: +_ 10%
Changeover Point: Based on measured resistance;_+ 1/2 decade on logarithmic scale
(i.e., 3.16 x 10n)
Changeover Point
Accuracy: +_ ½ decade
LED Measurement 11 LED's with Dual scales:
Indications: 103to 1012 Ohms/square per ASTM 257 in one decade increments
10
2to 1011 Ohms per S-11.11 in one decade increments
Over range indicator light for "Insulative" surfaces, i.e., >1012
Ohms/square or >1011 Ohms.
Auxiliary Connections: 2 ea. Female Banana for Resistance Range Performance
Verification and Direct Point to Point Resistance measurements
without electrodes.
1 ea. Point to Ground Phono Receptacle for resistance
measurements using one electrode
Operation Control: One (1) PUSH to TEST Button
Operating Range: 40oF to 120oF (5oC to 49oC)
Storage Temp: -15oC to +60oC
Relative Humidity: 0% to 90%
Battery Life: 40 hours typical
Dimensions: 115 mm x 69 mm x 26 mm
Weight: 6 oz.
Rev: ESI-870 – 1-17-2020

ESI-870 Resistance/Resistivity Indicator
18

Copyright 2001-2020, ESD Check
Printed in U.S.A.
www.esdcheck.com