Proteus EEC-1500 User manual

Owner's manual
EEC-1500/1550

STEP 1. FOLD UP THE HANDLEBAR
POST ( 17 ) TO THE UPRIGHT
POSITION, FIX WITH BOLTS
( 34 / 35 ) AND WASHERS ( 36 ).
STEP 2. FIX THE BEAM PANEL ( 37 )
TO THE MAIN FRAME ( 01 )
WITH SCREW ( 39 ). REPEAT
SAME PROCEDURE ON BEAM
PANEL ( 38 ).
NOTE: THE PEDAL ARMS ARE NOT FIXED WITH BOLTS. DO NOT HOLD THE PEDAL
ARMS FOR MOVING THE MACHINE.
EEC-1500/1550 ELLIPTICAL ASSEMBLY INSTRUCTION
17
35
36
34
36
27
14
1
26
17
39
37
27
26
38
14
1
- 1 -
STEP 3. ATTACH FRONT STABILIZER ( 02 ) & REAR STABILIZER ( 03 ) TO MAIN FRAME ( 01 ), FIX
WITH CARRIAGE BOLTS ( 40 ), WASHERS ( 42 ) AND NUTS ( 41).
STEP 4. ( FOR EEC-1550 ONLY ) INSERT ADJUST TUBE ( 52 ) TO THE CONNETICTING ARM ( 13,14)
AND FIX WITH KNOB ( 54 ) AS FIG 1.
STEP 5. FIX PEDAL (L)( 10 ) TO PEDAL ARM (L)( 04 ) WITH SCREWS ( 43 ) & WASHERS ( 44 )
TIGHTENED FIRMLY. REPEAT SAME PROCEDURE ON THE RIGHT PEDAL THEN
ASSEMBLE PEDALARM ASSEMBLY LEFT AND RIGHT ( 04 / 05 ) AS FIG. 1 & FIG. 2.
FIG. 2 INSERT THE SHAFT ( AT REAR SIDE OF PEDAL ARM ) TO THE CRANK JOINT ( 16 )
AT THE MAIN FRAME )
FIG. 3 THEN INSERT THE OTHER SHAFT (AT FRONT SIDE OF PEDAL ARM) TO THE
CROSS JOINT ( 15 ) ( AT CONNECTING ARM (L)( 13 ) & ARM (R)( 14 ) )
STEP 6. CONNECT PULSE WIRE (A)( 28 ) ( LOCATED ON LOWER END OF HANDLEBARS ) &
PULSE WIRE (B)( LOCATED ON UPPER END OF CONNECTING ARMS ) THEN INSERT THE
HANDLEBARS ( 06 / 07 ) TO THE CONNECTING ARMS ( 13 / 14 ) AND FIX WITH BOLTS
( 46 ), CONICAL BUSHINGS ( 48 ) & NUTS ( 47 ).

EXPLODED VIEW
- 2 -
FIG. 2
16
FIG. 3
15
FIG. 1
53
15
52
54
14
45
31
28 7,30
29
26
47
48
6,30
10
4
46 48
17
44
41 42
14
13
40
48
46
20
51
45
31
28
28
29
47
48
28 29
25
22
16
43 1 24 15
2
18
11
44
5
43
41
42
19
40
3

- 3 -
STEP 6. CONNECT MONITOR CABLE (A)( 26 ) & PULSE WIRE (B)( 29 ) TO THE MONITOR ( 12 )
THEN FIX THE MONITOR TO MOUNTING PLATE ( LOCATED ON TOP OF HANDLEBAR
POST) WITH SCREWS ( 49 ). ( PLEASE REFER TO FIG. 4 or FIG. 5 )
STEP 7. FIT REST HANDLE ( L / R ) ( 08 / 09 ) TO HANDLEBAR POST ( 17 ) & FIX WITH BOLT ( 50 )
AND CONNETICTING BRACKET ( 55 ) THEN FIX HANDLES WITH BOLTS ( 46 ), CONICAL
BUSHINGS ( 48 ) & NUTS ( 47 ).
NOW YOUR EEC-1500/1550 ELLIPTICAL HAS BEEN WELL ASSEMBLED.
BATTERIES MUST BE REMOVED FROM THE APPLIANCE BEFORE IT IS SCRAPPED AND
THAT THEY ARE DISPOSED OF SAFETY.
51
17
48
46
12
26
14
13
20
48 47
49
29
50
8,32
9,33
8,32
48
46
17
12
26
29
49
13
14
20
47
48
9,33
50
FIG. 4 FIG. 5
55 55
50 50
EEC-1500 EEC-1550

PARTS LIST
- 4 -
KEY Q'TYDESCRIPTION
1 MAIN FRAME 1
2 FRONT STABILIZER 1
3 REAR STABILIZER 1
4 PEDAL ARM (L) 1
5 PEDAL ARM (R) 1
6 HANDLEBAR (L) 1
7 HANDLEBAR (R) 1
8 REST HANDLE (L) 1
9 REST HANDLE (R) 1
10 PEDAL (L) 1
11 PEDAL (R) 1
12 MONITOR 1
13 CONNECTING ARM (L) 1
14 CONNECTING ARM (R) 1
15 CROSS JOINT 2
16 CRANK JOINT 2
17 HANDLEBAR POST 1
18 TRANSPORTATION WHEEL 2
19 FEET CAP 2
20 PIVOT END CAP 2
21 SWIVEL PLATE (L) 1
22 SWIVEL PLATE (R) 1
23 PROTECTING COVER (L) 1
24 PROTECTING COVER (R) 1
25 PEDALARM CAP 4
26 MONITOR CABLE (A) 1
27 MONITOR CABLE (B) 1
28 PULSE WIRE (A) 2
29 PULSE WIRE (B) 2
30 FOAM GRIP (A) 2
31 FOAM GRIP (B) 2
32 FOAM GRIP (C) 1
33 FOAM GRIP (D) 1
34 BOLT 2
35 BOLT 2
36 WASHER 4
37 BEAM PANEL (L) 1
38 BEAM PANEL (R) 1
39 SCREW 4
40 CARRIAGE BOLT 4
41 NUT 4
42 CURVED WASHER 4
43 SCREW 6
44 WASHER 6
45 HANDLEBAR END CAP 2
46 BOLT 6
47 NUT 6
48 CONICAL BUSHING 12
49 SCREW 4
50 SCREW 1
51 TENSION CONTROL 1
52 ADJUST TUBE 2
53 SLEEVE 2
54 KNOB 2
55 CONNETIC TING BRACKET 1
KEY Q'TYDESCRIPTION

GB
EEC15001550-030812GB