Proteus EEC-7000 User manual

Owner's manual
OMETER MAGNETIC
PROGRAMMABLE
ELLIPTICAL
ERG
EEC-7000

- 1 -
EEC-7000 ERGOMETER MAGNETIC
PROGRAMMABLE ELLIPTICAL ASSEMBLY INSTRUCTION
STEP 1.
a. FIT FOOT CAPS ( 23 ) TO END OF THE
REAR STABILIZER AND CAPS ( 21 ) TO END
OF THE FRONT STABILIZER.
( PLEASE REFER TO FIG. A )
b. THE CAPS ( 21 ) SHOULD BE TIGHTENED
WITH FOOT ADJUST BASE ( 22 ).
( PLEASE REFER TO FIG. B )
STEP 2.
a. CONNECT EXTENSION CABLE WIRE ( 08 )
AND LOWER CABLE WIRE ( 09 ).
b. FIT HANDLEBAR POST ( 02 ) TO THE MAIN
FRAME ( 01 ) BY USING M8 CARRIAGE
BOLTS ( 33 ), M8 SMALL WASHERS ( 44 ),
M8 NYLON NUTS ( 46 ) AND M8 HALF
MOON CAPS ( 47 ).
( PLEASE REFER TO FIG. C )

- 2 -
STEP 4.
a. FIT HANDRAIL TO CONNECTING ARM ( 04 )
WITH BOLT ( 34 ), WASHER ( 42 ) & NUT
( 46 ). BE SURE TO TIGHTEN BOLT
FIRMLY THEN FIT HALF MOON CAPS ( 20 )
ON BOTH ENDS.
b. REPEAT SAME PROCEDURE ON
ASSEMBLING THE CONNECTING ARM ( 04 )
& PEDAL ARM ( 05 ).
c. REPEAT SAME PROCEDURE ON THE
OTHER SIDE.
( PLEASE REFER TO FIG. F )
STEP 3.
a. INSERT AXLE SPACER ( 13 ), WAVE WASHER
( 57 ) PIVOT CAP-A ( 14 ), THEN FIT
HANDRAIL ( 03 ) TO THE AXLE BY USING M8
MIDDLE WASHER ( 43 ) AND M8 BOLT ( 36 ).
( TIGHTEN THE BOLT FIRMLY ).
b. FIT ANOTHER PIVOT CAP-B ( 15 ) IN RIGHT
POSITION WITH SLIGHTPUSH ( NO SCREW ).
( PLEASE REFER TO FIG. D )
c. REPEAT SAME PROCEDURE ON THE OTHER
SIDE HANDRAIL ( 03 ).
( PLEASE REFER TO FIG. E )

- 3 -
STEP 5.
CONNECT EXTENSION CABLE WIRE ( 08 ) &
GRIP PULSE WIRE ( 10 ) TO THE COMPUTER
( 07 )
THEN FIX IT ONTO HANDLEBAR POST BY
USING SCREWS ( 39 ).
( PLEASE REFER TO FIG. G )
STEP 6.
ATTACH WATER BOTTLE RACK ( 53 ) TO
HANDLEBAR POST ( 02 ) WITH M5
SCREWS ( 55 ) THEN ATTACH WATER
BOTTLE ( 54 ) INTO WATER BOTTLE RACK
( 53 )
( PLEASE REFER TO FIG. H )
" THE BATTERIES MUST BE REMOVED FROM THE APPLIANCE BEFORE IT IS
SCRAPPED AND THAT THEY ARE DISPOSED OF SAFELY ".
NOTE : THE MACHINE IS REQUESTED TO USE AC ADAPTER, WHICH SHOULD
BE WITH OUTPUT 6V/1000 MA, PLEASE ALSO REFER TO MONITOR
INSTRUCTION FOR THE PROPER SPECIFICATION INFORMATION.
NOW THE ASSEMBLY OF THE ERGOMETER MAGNETIC PROGRAMMABLE ELLIPTICAL IS
DONE.

- 4 -

- 5 -

PARTS LIST
NO. DESCRIPTION Q'TY
1. MAIN FRAME 1
2. HANDLEBAR POST 1
3. HANDRAIL 2
4. CONNECTING ARM 2
5. PEDAL ARM 2
6. HOLDER 2
7. COMPUTER 1
8. EXTENSION CABLE WIRE 1
9. LOWER CABLE WIRE 1
10. GRIP PULSE WIRE 1
11. GRIP PULSE 2
12. SLIDE TUBE 2
13. AXLE SPACER 2
14. PIVOT CAP - A 2
15. PIVOT CAP - B 2
16. FOOT PEDAL 2
17. CHAIN COVER (R) 1
18. CHAIN COVER (L) 1
19. CRANK COVER 2
20. HALF MOON CAP 10
21. CAP 2
22. FOOT ADJUST BASE 2
23. FOOT CAP 2
24. SLIDE TUBE PLUG 4
25. 25 x 50 PLUG 2
26. 38 ROUND PLUG 4
27. 1/4" WASHER 4
28. 1/4" SCREW x 37mm 4
29. SPACER x 32mm 2
NO. DESCRIPTION Q'TY
30. FOAM GRIP x 360mm 2
31. FOAM GRIP x 130mm 2
32. 64 PU WHEEL 4
33. M8 CARRIAGE BOLT x 70mm 4
34. M8 BOLT x 75mm 4
35. M8 BOLT x 42mm 4
36. M8 BOLT x 15mm 4
37. PU WHEEL COVER 4
38. M6 SCREW x 5mm 8
39. M5 SCREW x 20mm 4
40. M6 SCREW x 15mm 2
41. STUD SHAFT 2
42. M8 BIG WASHER 10
43. M8 MIDDLE WASHER 2
44. M8 SMALL WASHER 14
45. M6 WASHER 2
46. M8 NYLON NUT 12
47. M8 HALF MOON CAP 8
48. BEARING 608ZZ 8
49. SPACE x 5.5mm 8
50. BEARING 6003ZZ 16
51. SPACE x 49mm 4
52. SPACEx 60mm 2
53. WATER BOTTLE RACK 1
54. WATER BOTTLE 1
55. M5 SCREW 2
56. BEARING 6003ZZ 4
57. WAVE WASHER 8
- 6 -

GB
EEC7000-030418GB