Proteus EEC-1800 User manual

Owner's manual
-
EEC 1800 / 1850
All manuals and user guides at all-guides.com
all-guides.com

EEC-1800 / 1850 ELLIPTICAL ASSEMBLY INSTRUCTION
IF YOUR MODEL IS EEC-1800, PLEASE DO
STEP 2-1.
IF YOUR MODEL IS EEC-1850, PLEASE DO
STEP 2-2.
STEP 2-1.
a. CONNECT EXTENSION CABLE WIRE ( 08 ) AND
LOWER CABLE WIRE ( 09 ).
b. INSERT TENSION CABLE ( 46 ) INSIDE OF
HANDLEBAR POST ( 02 ).
c. FIT HANDLEBAR POST ( 02 ) TO THE MAIN
FRAME ( 01 ) BY USING M8 CARRIAGE BOLTS
( 33 ), M8 SMALL WASHERS ( 34 ), M8 NYLON
NUTS ( 32 ) AND M8 HALF MOON CAPS ( 25 ).
( PLEASE REFER TO FIG. C )
STEP 2-2.
a. CONNECT MONITOR CABLE (A) ( 43 ) AND
MONITOR CABLE (B)( 44 ).
b. FIT HANDLEBAR POST ( 02 ) TO THE MAIN
FRAME ( 01 ) BY USING M8 CARRIAGE BOLTS
( 33 ), M8 SMALL WASHERS ( 34 ), M8 NYLON
NUTS ( 32 ) AND M8 HALF MOON CAPS ( 25 ).
( PLEASE REFER TO FIG. D )
STEP 1.
a. FIT FOOT CAPS ( 23 ) TO END OF THE REAR
STABILIZER AND CAPS ( 21 ) TO END OF THE
FRONT STABILIZER.
( PLEASE REFER TO FIG. A )
b. THE CAPS ( 21 ) SHOULD BE TIGHTENED WITH
FOOT ADJUST BASE ( 22 ).
( PLEASE REFER TO FIG. B )
23
23
1
FIG.A
FIG.B 21
1
46 9
21 22
22
2
25
32
34
FIG.C
1
8
9
46
33
FIG.D
1 43
44
- 1 -
All manuals and user guides at all-guides.com

STEP 4.
a. SLIDE CONNECTING ARM ( 04 ) INTO
HANDRAIL-L ( 3L ), ADJUST PEDAL ARM ( 05 )
TO DESIRED HEIGHT AND TIGHTEN WITH
KNOB ( 24 ).
( PLEASE REFER TO FIG. G )
b. REPEAT SAME PROCEDURE ON REPEAT
SAME PROCEDURE ON THE OTHER SIDE.
STEP 3.
a. INSERT AXLE SPACER ( 13 ), WAVE WASHER
( 49 ), PIVOT CAP-A ( 14 ), THEN FIT HANDRAIL-
L ( 3L ) TO THE AXLE BY USING M8 MIDDLE
WASHER ( 35 ) AND M8 BOLT ( 36 ). ( TIGHTEN
THE BOLT FIRMLY ).
b. FIT ANOTHER PIVOT CAP-B ( 15 ) IN RIGHT
POSITION WITH SLIGHT PUSH ( NO SCREW ).
( PLEASE REFER TO FIG. E )
c. REPEAT SAME PROCEDURE ON THE OTHER
SIDE HANDRAIL-R ( 3R ).
( PLEASE REFER TO FIG. F )
- 2 -
3L
24
4
5
FIG. G
3L
36
FIG. E
15 35 13
14
2
49
36
35
213 3R
14
15
FIG. F
49
All manuals and user guides at all-guides.com

ASSEMBLE TENSION CONTROL, MONITOR :
IF YOUR MODEL IS EEC-1800, PLEASE DO
STEP 5 & STEP 6.
IF YOUR MODEL IS EEC-1850, PLEASE DO
STEP 7.
STEP 5.
a. RELEASE THE SCREW ( 48 ) FROM THE PARTS
OF TENSION CONTROL ( 45 ).
b. PULL THE TENSION CABLE ( 46 ) OUT FROM
MIDDLE HOLE OF HANDLEBAR POST ( 02 ).
c. ASSEMBLE TENSION CONTROL ( 45 ) AND
TENSION CABLE ( 46 ), BY CONNECTING
CABLE HEAD ( ON TENSION CONTROL ( 45 ) )
TO THE DRAW HOOK OF TENSION CABLE ( 46 ).
d. INSERT TENSION CONTROL ( 45 ) ONTO
HANDLEBAR POST ( 02 ). NOTE THE DRAW
HOOK ( ON TENSION CONTROL ( 45 ) ) WELL
INSERTED ONTO HANDLEBAR POST ( 02 ).
THEN TIGHTEN WITH SCREW ( 48 ) AND
WASHER ( 47 ).
( PLEASE REFER TO FIG. H )
STEP 6.
a. CONNECT EXTENSION CABLE WIRE ( 08 ) AND
GRIP PULSE WIRE ( 10 ) TO THE COMPUTER
( 07 ).
b. FIX COMPUTER ( 07 ) ONTO HANDLEBAR POST
( 02 ) BY USING SCREWS ( 39 ).
( PLEASE REFER TO FIG. I )
STEP 7.
a. CONNECT MONITOR CABLE (A)( 43 ) & GRIP
PULSE WIRE ( 10 ) TO THE COMPUTER ( 07 ).
b. FIX IT ONTO HANDLEBAR POST ( 02 ) BY
USING SCREWS ( 39 ).
( PLEASE REFER TO FIG. J )
39
2
43 10
7
FIG. J
2
39
7
810
FIG. I
FIG. H
46 46
45
48 47
2
45
46
45
10
8
- 3 -
All manuals and user guides at all-guides.com