ProWorld TRANSPRO SEMI-AUTO CAP User manual

www.ProWorldInc.com
Pro World Inc.
961 Bethel Ave.
Pennsauken, NJ 08110
Toll Free 800-678-8289
Outside U.S. 856-406-1020
Fax [phone]
HEAT PRESS USER’S GUIDE
MP980

PRO WORLD’S TRANSPRO SEMI-AUTO CAP PRESS
Page 2
www.proworldinc.com
Specifications
Model No: TransPro® Auto Open Cap Heat Press (MP980)
Voltage: 110V
Timer controller range: Adjustable
Rating power consumption: 600W
Temperature adjustment range: 0-260 Celsius / 0 to 500 F
Working dimension: 5.5" w x 3.5"
Figure size: 6.5"w x 19" h x 16"
N.W. : KG / 33 Lbs
Pressure Adjustment Knob
Heating Board
Pressure Handle
Temperature &
Timer Control
Power Switch
Cap Holding Device

OPERATION INSTRUCTIONS
Read Before Operating
1. Be sure to operate with safe ground wire!!!
2. Check the voltage before using it. The correct voltage is 110-120v.
3. Turn off the machine when not in use.
4. Grasp the handle firmly when opening.
5. Keep children away from the machine.
6. Do not attempt to press products that are not intended for normal heat transfer
use.
Operation Procedures
1. Plug in and turn on the power switch. The red light will illuminate.
2. Adjust the temperature by pressing the set button. Use arrows to choose desired
temperature. Press the set button again.
3. Allow 20-30 minutes for machine to heat to set temperature.
4. Adjust the timer by pressing the set button. Use arrows to choose desired time duration.
Press the set button again.
5. Pressure adjustment: Set pressure to a firm, comfortable lockdown. The pressure may
have to be adjusted depending on the transfer application instructions. Turn to the right to
tighten the pressure, turn left to lower the pressure.
6. Pull up the cap holding device and place the cap on the heat press pad. Close the cap
holding device to hold the cap in place.
7. Place your transfer on the cap and secure with a heat transfer tape.
8. Close and lock your heat press by pulling the handle down. This will begin the application
process.
9. Once the timer counts down, the platen will release and open.
10. Peel the transfer to reveal the printed cap.
Maintenance & Troubleshooting
1. Pressure: If the pressure is not heavy enough or too heavy, please adjust the
pressure adjuster. Turn to the right to tighten the pressure, turn left to lower the pressure.
2. Timer If the buzzer doesn't beep or keeps beeping when the duration runs out,
then please check the detector switch.
3. Temperature: The temperature LCD will display the temperature reaches the
preset value (i.e.: 385 Fahrenheit). If the heating element doesn't work please
check the circuit.
Connecting Your Heat Press To An Electrical Outlet
• Connect the power cord into a properly grounded electrical outlet with a
sufficient amperage rating.
• Your Pro World Heat Press requires a full 15 amp grounded circuit for 120 volt
operation.
• Extension cord use on the heat transfer machines is not recommended.
• Extension cords ,if used, should be as short as possible and not less then 12
gauge. Heavy duty extension cords are highly recommended in this case.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE:
1. Erratic controller functions.
2. Inaccurate displays and slow heat-up.
3. The fuse to pop/break.
4. Internal malfunctions prevent the machine to perform properly
Page 3
www.proworldinc.com

WIRING SCHEMATIC
Page 4
www.proworldinc.com
Thermal
Time
controller
Grounding
Time and temperature controller display
1234567
1011121314
+-
Power
(220V/110V,50-60HZ)
L N GND

TRANSPRO WARRANTY
Warranty Coverage
TransPro products offered by Pro World are warranted against defects in material
and workmanship. Warranty is void if equipment has been damaged by accident,
unreasonable use, neglect, unauthorized and/or improper service, or other causes
not arising out of defects in material and workmanship. This warranty does not cover
damage caused by normal wear and tear, neglect or lack of proper maintenance.
Warranty Duration
The heating element shall be warranted for the life of the cap press. There is a one
(1) year warranty on major components, circuit boards and all other components.
Warranty Performance
During the warranty period, and in the event that a situation cannot be resolved by
telephone/email and upon PRE-AUTHORIZATION from Pro World equipment must
be shipped, freight prepaid to Pro World for service in the original packaging. After
30 days, all shipping and insurance expenses to and from Pro World of in-warranty
equipment is solely the responsibility of the customer. Prior to 30 days the shipping
costs will be refunded if Pro World deems the equipment to be defective as stated.
Pro World cannot be held responsible for improper handling or any other damage
incurred in transit. No charge will be made for labor and components for repair of
in-warranty equipment. OUT-OF WARRANTY machines will be charged at the repair
rates in effect at the time the machine is received.
Warranty Disclaimers
Pro World shall not be liable for loss of use of TransPro equipment or other inciden-
tal or consequential costs, expenses, or damages incurred by the original purchaser
or any other user. The above warranty provisions constitute the entire agreement
between all parties, and supersede any and all prior written and/or oral representa-
tions and understandings.
This "Limited Warranty" applies to all TransPro equipment. However, the procedure
for obtaining service may vary outside the continental United States. Contact your
Pro World representative for warranty information. The purchaser is responsible for
compliance with all local laws, regulations and measure. Agreement shall be
governed by and construed in accordance with all applicable laws of said region.
Page 5
www.proworldinc.com

www.ProWorldInc.com
Pro World Inc.
961 Bethel Ave.
Pennsauken, NJ 08110
Toll Free 800-678-8289
Outside U.S. 856-406-1020
Fax [phone]