Proxim Tsunami Multipoint MP-820-BSU-100 User manual

Tsunami 800 and 8000 Series
(Point-to-point and Point-to-multipoint Products)
Hardware Installation Guide
Products Covered
--> Tsunami®Multipoint
- MP-820-BSU-100
- MP-825-BS3-100
- MP-8100-BSU
- MP-8200-BSU; MP-8250-BS9; MP-8250-BS1
- MP-820-SUA-50+
- MP-825-SUR-50+
- MP-825-CPE-50
- MP-825-CPE-100
- MP-8100-SUA
- MP-8150-SUR
- MP-8150-SUR-100
- MP-8150-CPE
- MP-8200-SUA
- MP-8250-SUR
- MP-8160-BSU and MP-8160-BS9
- MP-8160-SUA
- MP-8160-CPE
- MP-826-CPE-50
--> Tsunami Quickbridge®
- QB-8100-EPA / LNK
- QB-8150-EPR / LNK
- QB-8150-LNK-100
- QB-8150-LNK-12/50
- QB-8151-EPR / LNK
- QB-8200-EPA / LNK
- QB-8250-EPR / LNK
- QB-825-EPR / LNK-50
- QB-825-EPR / LNK-50+

Tsunami®800 and 8000 Series - Hardware Installation Guide 2
Copyright
2013 Proxim Wireless Corporation, Milpitas, CA. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634;
5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. The content described herein are copyrighted with all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means
without the written permission of Proxim Wireless Corporation.
Trademarks
Tsunami®, Proxim, and Proxim logo are the trademarks of Proxim Wireless Corporation. All other trademarks mentioned herein are the property of
their respective owners.
Disclaimer
Proxim reserves the right to revise this publication and to make changes in content from time-to-time without obligation on the part of Proxim to
provide notification of such revision or change. Proxim may make improvements or changes in the product(s) described in this guide at any time.
When using these device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons.
Tsunami®800 and 8000 Series - Hardware Installation Guide
Documentation Version: 5.1
P/N 765-00132, April 2014

Tsunami®800 and 8000 Series - Hardware Installation Guide 3
    
        
                       ! "  !  # "    $   % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % &
'  (   ) ( ! * +  )   * '  (   ) ( ! * ,   )   - ' + ' , . % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / 0
1 2 3 3 4     5 6 7    8    9 :   :   8      5   ; ;                                         <
' # *  =  * > ? * /   @ ' # *  =  * ?  * A  B @ ' # *  =  * ?  * /   @ ' # *  = A * ? C * A  B @ ' # *  = A * > 0 * /   @ D > *
 = A * E # C @ F G H * A  B / I
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS TU
VRWKXRY ZY[OL\OY ] ^LY SSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSSS T_
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS T_
b \YO\\K ] ^LYc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S Td
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S Tf
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS Tf
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS Tj
' # *  = A * k # E * /   @ ' # *  = A * k # E * A  @ D > *  = A * E # C l F G H * A  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % = 
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS mn
ZY[OL\OY ] ^LY o] ^Z ip K\M q KYKrSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSS SSSSSSSSSSS S mn
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S mj
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS mj
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS st
' # *  = u * k # E * A  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % 0 u
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS sd
ZY[OL\OY ] ^LY o] ^Z ip K\M q KYKrSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSS SSSSSSSSSSS S sd
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S sf
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS sf
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS sn
v 2 3 3 3 4     5 6 7    8    9 :   :   8      5   ; ;                                       < <
' # *  /   * > ? l ?  @ ' # *  / A  * ? C @ D > *  /   * E #  l F G H @ D > *  / A  * E # C l F G H @ D > *  / A / * E # C l F G H I I
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS UU
VRWKXRY ZY[OL\OY ] ^LYcSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSSS U _
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS U d
b \YO\\K ] ^LYc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S U f
VL^e\MR\W ] ^R\Yc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS U f
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS U f
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS U j
' # *  / u  * > ? @ ' # *  / u  * ?  @ ' # *  / u  * > & % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % A 
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS _n
VRWKXRY ZY[OL\OY ] ^LYcSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSSS _n
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS _j
b \YO\\K ] ^LYc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S dt

Tsunami®800 and 8000 Series - Hardware Installation Guide 4
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S dt
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS dT
i \ c Y K a a K Y R ^ \ ] L ^ g O M e L O S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S d m
' # *  / A  * k # E @ D > *  / A  * F G H * / = @ A  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % w =
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS fm
ZY[OL\OY ] ^LY o] ^Z ip K\M q KYKrSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSS SSSSSSSSSSS S fm
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS fm
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S fs
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS fU
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS f_
' # *  / u  * k # E *  /   % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % %  /
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS nT
ZY[OL\OY ] ^LY o] ^Z ip K\M q KYKrSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSS SSSSSSSSSSS S nT
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S nT
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS nm
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS nm
' # *  / A  * ? C * /   @ D > *  / A  * F G H * /   % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % %  
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS nn
VRWKXRY ZY[OL\OY ] ^LY SSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSSS nn
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS nj
VL^e\MR\W ] ^R\Y SSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSS S nj
] L^MegY ] KghKWO SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS jt
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSS jT
' # *  =   * > ? @ ' # *  =   * ?  @ ' # *  = A  * ? C @ D > *  =   * E #  l F G H @ D > *  = A  * E # C l F G H @ ' # *  = A  * > &
@ ' # *  = A  * > / & 
J KLMN KLO P Q OLQ RON SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSS jn
VRWKXRY ZY[OL\OY ] ^LYcSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSSS jn
`OLRKa] ^LY SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSS jj
b \YO\\K ] ^LYc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSS Ttt
VL^e\MR\W ] ^R\Yc SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS TtT
] L^MegY ] KghKWO SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS SSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSS SSSSS TtT
i\cYKaaKYR^\ ] L^gOMeLO SSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSS Tts
< x y   ;4 z   5  1
{ ! |  $ ! '   ! (  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / =
 $ $ !    "  !  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / u
, } { ' '    (      C   !  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / 
~  " ! ( !   # "    $  ( % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / 
+   ! "   $ !  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / &
% % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / / &
 "       #   ! " !       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / = 

Tsunami®800 and 8000 Series - Hardware Installation Guide 5
C ! $ !  | ! !      |    % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / = 0
'     !  !   % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / 0 /
#   ! "  ) ) (  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / 0 =
  "    " ! ) ! $    $       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / 0 A
+   !  "   !     !    ) ! $    $       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / 0 w
#     $  ( ) ! $    $       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / I w
E  |  "    !    ( ) ! $    $       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / I 
'  > } % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / I &
  z z      6          ;     y   z        4   z 5                                      3
'   ! "   (   " ~ !    ! " ) "       % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / A 
~ !    ! " ) "        ! )  % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % / A 
  z z    6   y        1
 z z    6   :   5   v
  z z    6 4       <
  z z      6 x   y     ; 4   :    5    4  z z                                           

Preface
Tsunami®800 and 8000 Series - Hardware Installation Guide 6
Preface
This chapter contains the following information:

b X ^ e Y Y [ R c Ve R M O

] L ^ M e g Y c  ^ Q O L O M

b e M R O \ g O

] L O L O  e R c R Y O c

O a K Y O M q ^ g e  O \ Y c

q ^ g e  O \ Y K Y R ^ \  ^ \ Q O \ Y R ^ \ c
About this Guide
A comprehensive guide that provides an overview about the Tsunami® 800 and 8000 series products, their installation
methods and hardware specifications.
Products Covered
Product(s) Supported Countries
MP-820-BSU-100 US, WD, EU
MP-825-BS3-100 US, WD, EU
MP-8100-BSU US, WD, EU
MP-8200-BSU US, WD, EU, JP
MP-8250-BS9 US, WD, EU
MP-8250-BS1 US, WD, EU
MP-820-SUA-50+US, WD, EU
MP-825-SUR-50+US, WD, EU
MP-825-CPE-50 US, WD, EU
MP-825-CPE-100 US, WD, EU
MP-8100-SUA US, WD, EU
MP-8150-SUR US, WD, EU
MP-8150-SUR-100 US, WD, EU
MP-8150-CPE US, WD
MP-8200-SUA US, WD, EU, JP
MP-8250-SUR US, WD, EU, JP
MP-8160-BSU WD
MP-8160-BS9 WD
MP-8160-SUA WD
MP-8160-CPE-A100 WD

Preface
Tsunami®800 and 8000 Series - Hardware Installation Guide 7
Audience
The intended audience for this guide is the network administrator who installs and/or manages the device.
Prerequisites
The reader of this document should have working knowledge of Wireless Networks, Local Area Networking (LAN) concepts,
Network Access Infrastructures and Client-Server Applications.
Related Documents
In addition to this guide, you can refer to the following documents that are available on the Proxim’s support site at
[ Y Y       S  L ^  R  S g ^ 

Quick Installation Guide (QIG) - A quick reference guide that provides essential information to install and configure
the device.

Software Management Guide - A guide that provides step-by-step instructions to configure, manage and monitor
the device by using Web Interface.

Reference Guide - A guide that provides step-by-step instructions to configure, manage and monitor the device by
using Command Line Interface (CLI).

Antenna Guides - A guide that gives insight on the recommended antennas for your product and ways to align the
antennas.

Safety and Regulatory Compliance Guide - A guide that provides country specific safety and regulatory norms to
be followed while installing the device.
MP-826-CPE-50 WD
QB-8100-EPA/LNK US, WD, EU
QB-8150-EPR/LNK US, WD, EU
QB-8150-LNK-100 US, WD, EU
QB-8150-LNK-12 WD
QB-8150-LNK-50 US, WD
QB-8151-EPR / LNK US, WD
QB-8200-EPA / LNK US, WD, EU, JP
QB-8250-EPR / LNK US, WD, EU, JP
QB-825-EPR/LNK-50 US, WD
QB-825-EPR/LNK-50+US, WD, EU
Product(s) Supported Countries

Preface
Tsunami®800 and 8000 Series - Hardware Installation Guide 8
Documentation Conventions
Icon Representation
Name Image Meaning
Note A special instruction that draws attention of a user.
Important A note of significant importance that the user should be aware of.
Caution A warning that cautions the user of a possible danger.

Tsunami®800 and 8000 Series - Hardware Installation Guide 9
Introduction
This chapter contains information on the following:

b X ^ e Y  c e \ K  R  n t t K \ M n t t t `O L R O c ] L ^ M e g Y c

e a Y R  a O  i \  e Y 

e a Y R  a O  P e Y  e Y o

i

P r
1.1 About Tsunami®800 and 8000 Series Products
Product Description Image
MP-820-BSU-100 The MP-820 Base Station unit, is a flexible wireless outdoor product
that operates in 5.150 – 5.925 GHz frequency band. This
connectorized device comes with 2x2 MIMO radio and two N-Type
connectors to connect external antennas. It provides an aggregate
throughput of 100 Mbps.
MP-825-BS3-100 The MP-825 Base Station unit comes with a 2x2 MIMO radio and 15
dBi integrated dual-polarized panel antenna that operates in 5.150 -
5.925 GHz frequency band. It provides an aggregate throughput of
100 Mbps.
MP-8100-BSU The MP-8100 Base Station unit, is a flexible wireless outdoor product
that operates in 2.3 – 2.5 and 4.9 – 6.0 GHz frequency band. This
connectorized device comes with a 3x3 MIMO radio and three
N-Type connectors to connect external antennas.
MP-8200-BSU The MP-8200 Base Station unit, is a flexible wireless outdoor product
that operates in 4.900 to 5.925 GHz frequency band. This
connectorized device comes with a 3x3 MIMO high power radio and
three N-Type connectors to connect external antennas.
MP-8250-BS9 The MP-8250 Base Station unit comes with a high power 2x2 MIMO
radio and 16 dBi integrated 90° sector antenna that operates in
4.900 – 5.925 GHz frequency band.
MP-8250-BS1 The MP-8250 Base Station unit comes with a high power 2x2 MIMO
radio and 23 dBi integrated 10° panel antenna that operates in 4.900
– 5.925 GHz frequency band.
MP-820-SUA-50+The MP-820 Subscriber unit, is a flexible wireless outdoor product
that operates in 5.150 to 5.925 GHz frequency band. This
connectorized device comes with a 2x2 MIMO radio and two N-Type
connectors to connect external antennas. It provides an aggregate
throughput of 50 Mbps, license upgradable to 100 Mbps.
MP-825-SUR-50+The MP-825 Subscriber unit comes with a 2x2 MIMO radio and 15
dBi integrated dual-polarized panel antenna that operates in 5.150 -
5.925 GHz frequency band. It provides an aggregate throughput of
50 Mbps, license upgradable to 100 Mbps.

Introduction
Tsunami®800 and 8000 Series - Hardware Installation Guide 10
MP-825-CPE-50 The MP-825 Customer Premises Equipment comes with a 2x2 MIMO
radio and 15 dBi integrated dual-polarized panel antenna that
operates in 5.15 - 5.925 GHz frequency band with aggregate
throughput of 50 Mbps.
MP-825-CPE-100 The MP-825 Customer Premises Equipment comes with a 2x2 MIMO
radio and 15 dBi integrated dual-polarized panel antenna that
operates in 5.150 - 5.925 GHz frequency band with aggregate
throughput of 100 Mbps.
MP-8100-SUA The MP-8100 Subscriber unit, is a flexible wireless outdoor product
that operates in 2.3 – 2.5 and 4.9 – 6.0 GHz frequency band. This
connectorized device comes with a 3x3 MIMO radio and three
N-Type connectors to connect external antennas.
MP-8150-SUR The MP-8150 Subscriber unit comes with a 2x2 MIMO radio and 23
dBi integrated dual-polarized panel antenna that operates in 4.900 –
5.925 GHz frequency band.
MP-8150-SUR-100 The MP-8150 Subscriber unit comes with a 2x2 MIMO radio and 21
dBi integrated dual-polarized panel antenna that operates in 4.900 –
5.875 GHz frequency band. It provides a throughput of up to 50
Mbps (Uplink) and 50 Mbps (Downlink).
MP-8150-CPE The MP-8150 Customer Premises Equipment comes with a high
power 2x2 MIMO radio and 16 dBi integrated dual-polarized panel
antenna that operates in 5.3 – 6.1 GHz frequency band.
MP-8200-SUA The MP-8200 Subscriber unit, is a flexible wireless outdoor product
that operates in 4.900 to 5.925 GHz frequency band. This
connectorized device comes with a 3x3 MIMO high power radio and
three N-Type connectors to connect external antennas.
MP-8250-SUR The MP-8250 Subscriber unit comes with a 2x2 MIMO high power
radio and 23 dBi integrated dual-polarized panel antenna that
operates in 4.900 – 5.925 GHz frequency band.
MP-8160-BSU The MP-8160 Base Station unit, is a flexible outdoor product that
operates in 5.900 – 6.425 GHz frequency band. This connectorized
device comes with a high power 2x2 MIMO radio and two N-Type
connectors to connect external antennas.
MP-8160-BS9 The MP-8160 Base Station unit comes with a 2x2 MIMO radio and 16
dBi integrated 90° sector antenna that operates in 5.900 – 6.425
GHz frequency band.
MP-8160-SUA The MP-8160 Subscriber unit, is a flexible outdoor product that
operates in 5.900 – 6.425 GHz frequency band. This connectorized
device comes with a high power 2x2 MIMO radio and two N-Type
connectors to connect external antennas.

Introduction
Tsunami®800 and 8000 Series - Hardware Installation Guide 11
MP-8160-CPE-A100 The MP-8160 Customer Premises Equipment comes with a single
high power 2x2 MIMO radio and 15 dBi integrated dual-polarized
panel antenna that operates in 5.900 – 6.425 GHz frequency band.
MP-826-CPE-50 The MP-826 Customer Premises Equipment comes with a 2x2 MIMO
radio, and 15 dBi integrated dual-polarized panel antenna that
operates in 5.900 – 6.425 GHz frequency band with a aggregate
throughput of 50 Mbps.
QB-8100-EPA The QB-8100-EPA QuickBridge operates in 2.3 – 2.5 and 4.9 – 6.0
GHz frequency band. This connectorized device comes with a 3x3
MIMO radio and three N-Type connectors to connect external
antennas.
QB-8100-LNK A pair of QB-8100-EPA devices form a link.
QB-8150-EPR The QB-8150-EPR QuickBridge comes with a 2x2 MIMO radio and 23
dBi integrated dual-polarized panel antenna that operates in 4.900 –
5.925 GHz frequency band.
QB-8150-LNK A pair of QB-8150-EPR devices form a link.
QB-8150-LNK-100 A pair of QB-8150-EPR-100 devices form a link.
The QB-8150-EPR-100 device comes with a 2x2 MIMO radio, 21 dBi
integrated dual-polarized panel antenna that operates in 4.900 –
5.875 GHz frequency band. It provides a throughput of up to 50
Mbps (Uplink) and 50 Mbps (Downlink).
QB-8150-LNK-12 A pair of QB-8150-EPR-12 devices form a link.
The QB-8150-EPR-12 device comes with a high power 2x2 MIMO
radio, 12 Mbps speed and 16 dBi integrated dual-polarized panel
antenna that operates in 5.3 - 6.1 GHz frequency band.
QB-8150-LNK-50 A pair of QB-8150-EPR-50 devices form a link.
The QB-8150-EPR-50 device comes with a high power 2x2 MIMO
radio, 50 Mbps speed and 16 dBi integrated dual-polarized panel
antenna that operates in 5.3 – 6.1 GHz frequency band.
QB-8151-EPR The QB-8151-EPR QuickBridge comes with a 2x2 MIMO radio and 21
dBi integrated dual-polarized panel antenna that operates in 4.900 –
5.875 GHz frequency band.

Introduction
Tsunami®800 and 8000 Series - Hardware Installation Guide 12
QB-8151-LNK A pair of QB-8151-EPR devices form a link.
QB-8200-EPA The QB-8200-EPA QuickBridge operates in 4.900 – 5.925 GHz
frequency band. This connectorized device comes with a 3x3 MIMO
high power radio and three N-Type connectors to connect external
antennas.
QB-8200-LNK A pair of QB-8200-EPA devices form a link.
QB-8250-EPR The QB-8250-EPR QuickBridge comes with a 2x2 MIMO high power
radio and 23 dBi integrated dual-polarized panel antenna that
operates in 4.900 – 5.925 GHz frequency band.
QB-8250-LNK A pair of QB-8250-EPR devices form a link.
QB-825-EPR-50 The QB-825-EPR-50 device comes with a 2x2 MIMO radio and 15 dBi
integrated dual-polarized panel antenna that operates in 5.15 -
5.925 GHz frequency band with aggregate throughput of 50 Mbps.
QB-825-LNK-50 A pair of QB-825-EPR-50 devices form a link.
QB-825-EPR-50+The QB-825-EPR-50+ device comes with a 2x2 MIMO high power
radio and 15 dBi integrated dual-polarized panel antenna that
operates in 5.150 – 5.925 GHz frequency band. It provides an
aggregate throughput of 50 Mbps, license upgradable to 100 Mbps.
QB-825-LNK-50+A pair of QB-825-EPR-50+ devices form a link.

Introduction
Tsunami®800 and 8000 Series - Hardware Installation Guide 13
1.2 Multiple-Input-Multiple-Output (MIMO)
Proxim’s Point-to-point and Point-to-multipoint devices support Multiple-Input-Multiple-Output (MIMO) antenna technology
that uses multiple antennas at both the transmitter and receiver to improve communication performance. The underlying
technology of Proxim’s product radios are based on a combination of MIMO and OFDM (Orthogonal Frequency Division
Multiplexing). MIMO-OFDM combination radios solve interference, fading and multi-path problems. On the receiver side,
having multiple receivers increases the amount of received power and also reduces multi-path problems by combining the
received signals for each frequency component separately. Hence, MIMO significantly improves the overall gain.
MIMO also uses Spatial multiplexing transmission technique to transmit independent and separately encoded data signals
from each of the multiple transmit antennas while reusing or multiplexing in the space dimension. These independent data
signals are called Spatial streams. The transmitting antenna uses multiple radio Tx chains and signal paths to simultaneously
transmit different data streams, whereas the receiver combines the Rx signals resulting in higher throughput.
By increasing the number of receiving and transmitting antennas, the throughput of the channel increases linearly resulting in
high spectral efficiency.

Tsunami®800 and 8000 Series - Hardware Installation Guide 14
800 Series - Hardware Overview and
Installation
This chapter provides hardware overview, and step-by-step procedure to install and mount the following Tsunami® 800
series products.

]  n m t   ` ¡  T t t 

]  n m t  ` ¡ b  _ t ¢ 

]  n m t  ` ¡ b  T t t 

]  n m _  ` ¡

 _ t ¢ 

]  n m _   `s  T t t 
£  n m _  Z ]

 ¤ p ¥  _ t ¢

]  n m _   ] Z  T t t 

]  n m _   ] Z  _ t  £  n m _  Z ]
 ¦
¤ p ¥  _ t

]  n m d   ] Z  _ t
2.1 MP-820-BSU-100 / MP-820-SUA-50+/ MP-820-SUA-100/ MP-825-SUR-50+
/ MP-825-BS3-100 / QB-825-EPR/LNK-50+
This section provides the hardware overview and installation procedure for the following products:

MP-820-BSU-100

MP-820-SUA-50+

MP-825-SUR-50+

MP-825-BS3-100

QB-825-EPR/LNK-50+
2.1.1 Hardware Overview
Figure 2-1 MP-820-BSU-100 / MP-820-SUA-50+

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 15
Figure 2-2 MP-825-SUR-50+ / MP-825-BS3-100/ QB-825-EPR-50+
A detailed description about the various components of the device are explained in the following sections.
2.1.1.1 Gigabit Ethernet Port
The device comes with one auto-sensing 10/100/1000 BASE-T Ethernet port with configurable Tx modes and speeds.
The Gigabit Ethernet port (PoE IN and Data) of the device allows the user to connect to the LAN by using Cat5e/Cat6 Ethernet
cable, and also power ON the device by using the Power over Ethernet (PoE) Injector supplied with the product package.

The device receives 48 VDC via a a standard Cat5e/Cat6 cable connected between the PoE and the device.

Maximum power supplied to the device is 32 Watts and the device typically draws 10 Watts.
Above 0° Celsius internal temperature, the device need not regulate its temperature, so the power drawn is generally lower in
this temperature range. When the internal temperature gets close to the limits, the device starts to heat itself and the power
draw increases. Powering the device when it is cold, triggers a special self-heat mode where the device is inoperable until the
internal temperature is above -20° Celsius. This is signaled by a solid yellow LED on the Ethernet connector. Once the internal
temperature is above -20° Celsius, the device boots normally.
2.1.1.2 Serial Port
The Serial Port is used for debugging and management and GPS Sync (Only for BSU).
The serial connection is established with an RJ11 to DB9 connector (also referred to as a “dongle”) by connecting the RJ11
end of the dongle connector to the device and the other end to your Personal Computer.
Recommended Ethernet Cable Specifications
Type Cat5e/Cat6, STP, 24 AWG, UL rated, UV-shielded and outdoor-rated
Impedance 100 ohms
Cable Length 330 feet / 100 meters
: The total length of cabling between the Personal Computer and the device
cannot exceed 100 meters (includes cable from the Personal Computer to
the PoE, and the cable from the PoE to the device. Due to DC power
requirements, the maximum cable length between the PoE Injector and the
device is 75 meters.

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 16
Figure 2-3 Serial Components

Product can be powered either by using 12V supply or through RJ11(Serial port) interface. Pin 6 of RJ11 is used to
supply 12V DC to the device.
– Product shall be supplied with 12V (+/-10%)/2A DC supply when Serial port power option is used.
– It is recommended to use cable length of less than 5M to reduce power dissipation/voltage drop in the cable.
– While using the Serial port power option, PoE power on Ethernet port shall not be used.
– Serial port cable gland shall be used with Serial power cable to make the product IP67 compliant.
2.1.1.3 Antenna Ports
: Applicable only to MP-820-BSU-100 and MP-820-SUA-50+
The Antenna Ports A1 and A2 are used to connect external antenna(s). These antenna connectors are of N-Type female with
built-in surge protection.

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 17
2.1.1.4 Grounding Point
To protect the device against lighting or ESD events, you must ground the device properly. To ensure proper grounding, use
either of the ground points that are situated at the bottom corner of the device and the grounding screw (M4 thread size)
provided to attach a ground wire of at least 12 AWG stranded to the device.
2.1.2 Product Package
Each shipment includes the items listed in the following table. Please verify that you have received all the parts in this
shipment, prior to installation.
What’s in the Kit Image
MP-820-BSU-100/
MP-820-SUA-50+/
MP-825-SUR-50+/
MP-825-BS3-100/
QB-825-EPR-50+
32 W PoE Injector with reload
button and country specific
Power Cord
WD - US, UK, and EU power cords
US - US power cord
EU - UK and EU power cords
RJ11 to DB9 Serial Connector
Connector Weather Proofing
Kit
Grounding Kit
Quick Installation Guide
MP-820-BSU-100 / MP-820-SUA-50+MP-825-SUR-50+ / MP-825-BS3-100/
QB-825-EPR-50+

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 18
:QB-825-LNK-50+contains two sets of all the above accessories.
Mounting Kit and Hardware
The mounting kit includes the following:

Mounting clamp for wall/pole

Extension arm

Mounting plate to enclosure

Mounting clamp for pole mounting
The following table lists and describes some of the items included with
the mounting kit:
What’s in the Kit Image
Quantity Description Image
6 each Plain washer #5/16
2 each Hex Cap Screw NC 5/16-18 x 35
2 each Nut NC 5/16-18
4 each Helical Spring Lock Washer #1/4
4 each Helical Spring Lock Washer #5/16
2 each Hex Cap Screw NC 5/16-18 x 80
4 each 68764, Screw, Machine, Pan,
Philips, 1/4"-20, 5/8"L

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 19
2.1.3 Installation Procedure
: Please note that we have taken MP-820-BSU-100 as an example to explain the steps to install and mount the device.
Please correlate the same with your device.
: The device must be installed by a trained professional who is familiar with radio frequency planning and
regulatory limits.
Perform the following steps to install and mount the device.
Step 1: Plan for Installation
There are several planning factors to be considered before installing the device. In addition to selecting the installation site,
you should do the following:
Calculate:

Required RSL and fade margin to achieve link availability objectives. For more details on how to calculate RSL and fade
margin, please refer to the ‘Antenna Installation Guide’ and ‘Proxim Link Calculator’ that are available on the support
site at
[ Y Y       S  L ^  R  S g ^ 
.

Required path availability

Anticipated multi-path reflection points
Determine:

System frequency plan

Required antenna mounting height to obtain proper path clearance

Required transmission line types (like cable, waveguides) and lengths
Plan for:

Device’s continuous power consumption needs

Lightning protection and system grounding

Hardware mounting

Cable installation including egress

Pre-testing equipment (back-to-back test procedure)
Step 2: Choose a Location
To make optimal use of the device, you must find a suitable location to install the hardware. The range of the radio device
largely depends upon the position of the antenna. Proxim recommends you do a site survey, observing the following
requirements, before mounting the hardware.

The location must allow easy disconnection of power to the radio, if necessary.

Ensure free flow of air around the hardware.

The radio device must be kept away from vibration and excessive heat.

The installation must conform to local regulations at all times.
The devices are designed to directly mount to a pole. By using the supplied brackets and hardware, you can mount them to a
1.25 inch to 3-inch pole (outside diameter). Longer bolts (not supplied) are required to mount the device to a larger diameter
pole. By using just one of the pole mounting brackets, you can mount the device to a wall or other flat surface.

800 Series - Hardware Overview and Installation
Tsunami®800 and 8000 Series - Hardware Installation Guide 20
Step 3: Gather Required Tools
You should have the following tools available before installing the device:

Cross-tip screwdrivers

Small blade standard screwdriver

Large blade standard screwdriver

Wire crimpers (if using connectors that are not pre-made)

Adjustable 6” wrench

Weatherproofing material for sealing external connectors (such as butyl tape)

Straight-through UV-protected STP-rated Cat5e/Cat6 Ethernet cable for connecting to PC, or cable for connecting to a
hub or a switch.
Step 4: Unpack the Product Package

Unpack the device and its accessories from the shipping box.

Please make a note of the Ethernet addresses, the MAC addresses and the serial number. These addresses may be
used when configuring the device. Note that the serial number helps you to seek support from the Proxim’s Customer
support team.
Step 5: Weatherproofing RJ45 Connectors
The following steps explain how to weatherproof the RJ45 connectors:
1. Use a straight-through cable (Cat5e/Cat6) with one end bare.
2. Connect the crimped RJ45 connector end of the cable into the RJ45 Ethernet port inside the enclosure. The cable
connector should latch into the Ethernet port.
3. Slide the Flat Washer (A) into the Connector Body (B) to make it waterproof and onto the bare end of the cable. Next,
fasten the Connector Body into the Ethernet connector hole on the device.
4. Slide the tube-shaped Compression Washer (C) into the Compression Ring (D) and onto the cable from the bare end,
and insert into the fixed Connector Body.
5. Slide the Sealing Nut (E) over the bare end of the cable and fasten it on the fixed Connector Body.
6. Crimp the bare end of the cable with RJ45 connector and connect it to the PWR LAN-OUT port on the PoE Injector.
Figure 2-4 Weatherproofing RJ45 Connector
Additional Weatherproofing Steps
To add an additional layer of protection to the connectors against the environment, see
b   O \ M R   b M M R Y R ^ \ K a
§ O K Y [ O L  L ^ ^ ¨ R \ W `Y O  c
.
For detailed explanation to weatherproof RF connections, refer to Antenna Installation Guide, which is available at
[ Y Y       S  L ^  R  S g ^ 
.