PT PT610 Installation guide

Innovative Measurement Electronics
PT610
PT620
PT630
Advanced
Weighing Indicators
Basic Instruction Manual Rev. 201803.3

CONTENTS
Table of ontents
1 NOTICES........................................................................1
1.1 SAFETY.................................................................1
1.2 PRECAUTIONS.....................................................1
2 DESCRIPTION...............................................................2
2.1 INTRODUCTION...................................................2
2.2 STANDARD SUPPLIED ITEMS............................2
2.3 ACCESSORIES SOLD SEPARATELY.................2
2.4 MODELS AND FEATURES...................................3
2.5 DEFINITIONS AND CONVENTIONS....................4
3 SPECIFICATIONS.........................................................6
4 INSTALLATION..............................................................9
4.1 GENERAL RULES.................................................9
4.1.1 INSTALLATION STEPS.....................................9
4.2 MECHANICAL INSTALLATION...........................10
4.2.1 OPENING/CLOSING THE HOUSING........12
4.3 INTERNAL CONNECTIONS...............................12
4.4 CONNECTING THE LOAD CELL........................13
4.5 POWER SUPPLY AND GROUNDING................13
4.6 ELECTRICAL OPTIONS.....................................14
4. ENERGISING THE INSTRUMENT.....................14
4.8 CONFIGURING AND CALIBRATION..................14
4.8.1 PROGRAMMING........................................14
4.8.2 CALIBRATION............................................14
4.8.3 LOCKING CALIBRATION...........................15
4.9 CHECKING SCALE PERFORMANCE................15
4.10 SERIAL PORT CONNECTION..........................15
4.10.1 RS-232C PORT CONNECTION.....................15
4.10.2 RS-485 PORT CONNECTION.......................16
4.10.3 USB CONNECTION.......................................1
4.10.4 ETHERNET CONNECTION...........................1
4.11 CLEANING THE INSTRUMENT........................1
4.12 DISPOSAL.........................................................1
5 OPERATION................................................................18
5.1 KEYPAD AND DISPLAY.....................................18
5.1.1 Keypad........................................................19
5.1.1.1 Key Locking..................................................21
5.1.2 Display........................................................21
5.1.3 Bar Graph...................................................22
5.2 BASIC WEIGHING..............................................22
5.2.1 Zeroing........................................................23
5.2.2 Taring..........................................................23
5.2.2.1 Taring, Multi-taring.......................................23
5.2.2.2 Clear Tare.....................................................23
5.2.2.3 Auto Tare......................................................23
5.2.2.4 Auto Clear Tare............................................23
5.2.2.5 Restore Tare.................................................23
5.2.2.6 Preset Tare...................................................23
5.2.3 Gross/Net Function.....................................24
5.2.4 Printing........................................................24
5.2.4.1 Single line.....................................................24
5.2.4.2 Multi line.......................................................24
5.2.4.3 EPL label......................................................25
5.3 ADVANCED WEIGHING.....................................25
5.3.1 Function Keys.............................................26
5.3.2 High Resolution...........................................26
5.3.3 Units Change..............................................26
5.3.4 Dynamic Weighing......................................26
5.3.5 Date and Time............................................26
5.3.6 Totalling weights.........................................26
5.3.6.1 Horizontal Totalling.......................................2
5.3.6.2 Vertical Totalling...........................................2
5.3.6.3 Piece Count Totalling...................................28
5.3.6.4 Displaying the Total......................................28
5.3.6.5 Grand Total...................................................28
5.3. Preset Tare Memory...................................28
5.3.8 Identification Memory..................................29
5.3.9 Piece Counting............................................30
5.3.10 Set-points..................................................34
5.3.11 Analogue output........................................38
5.3.12 EZAZ Smart Apps.....................................39
5.3.12.1 EZAZ Check-Weighing...............................39
Digital inputs and outputs......................................41
5.3.12.2 EZAZ Grading.............................................42
5.3.12.3 EZAZ Filling................................................44
5.4 ADVANCED SETTINGS......................................4
5.4.1 Tilt Switch....................................................4
5.4.2 Key lock......................................................4
5.4.2.1 PT610...........................................................48
5.4.2.2 PT620, PT630..............................................48
5.4.3 Passwords..................................................48
5.4.3.1 PT610...........................................................48
5.4.3.2 PT620, PT630..............................................48
5.4.4 Date and Time............................................49
5.4.5 Language....................................................49
5.4.6 Bar graph....................................................50
5.4. Alibi memory...............................................50
5.4.8 Stability filter................................................50
5.4.9 Tare Operation............................................50
5.4.10 Serial Data Communication......................50
5.4.10.1 Serial Port RS-232C.1................................50
5.4.10.2 Serial Port RS-232C.2................................51
5.4.10.3 Serial Port RS-485.....................................51
5.4.10.4 USB Port.....................................................51
5.4.10.5 Ethernet Port..............................................51
5.4.10.6 Continuous Data Formats..........................51
5.4.10. BSI Communication....................................52
5.4.10.8 CHK Checksum..........................................61
5.4.11 Printer Settings.........................................61
5.4.12 Test Menu.................................................61
6 SYSTEM CONFIGURATION AND SETUP..................62
6.1 ENTERING AND EXITING SETUP.....................63
6.2 [1__] – INTERFACE PARAMETERS...................64
6.2.1 [11_] – RS-232C.1......................................64
6.2.1.1 [111 FORMAT] – Data Format.....................64
6.2.1.2 [112 BAUD] – Baud Rate.............................64
6.2.1.3 [113 LENGTH] – Data Length......................64
6.2.1.4 [114 PARITY] – Parity..................................64
6.2.1.5 [115 CSUM] – Checksum.............................64
6.2.1.6 [116 CR] – Carriage Return..........................64
6.2.1. [11 LFEED] – Line Feed.............................64
6.2.1.8 [118 DELAY] – Response Speed.................64
6.2.1.9 [119 ADDRESS] – Port address..................65
6.2.2 [12_] – RS-232C.2......................................65
6.2.2.1 [121 FORMAT] – Data Format.....................65
6.2.2.2 [122 BAUD] – Baud Rate.............................65
6.2.2.3 [123 LENGTH] – Data Length......................65
6.2.2.4 [124 PARITY] – Parity..................................65
6.2.2.5 [125 CSUM] – Checksum.............................65
6.2.2.6 [126 CR] – Carriage Return..........................65
6.2.2. [12 LFEED] – Line Feed.............................65
6.2.2.8 [128 DELAY] – Response Speed.................65
6.2.2.9 [129 ADDRESS] – Port address..................65
6.2.3 [13_] – RS-485............................................65
6.2.3.1 [131 FORMAT] – Data Format.....................65
6.2.3.2 [132 BAUD] – Baud Rate.............................66
6.2.3.3 [133 LENGTH] – Data Length......................66
6.2.3.4 [134 PARITY] – Parity..................................66
6.2.3.5 [135 CSUM] – Checksum.............................66
6.2.3.6 [136 CR] – Carriage Return..........................66
6.2.3. [13 LFEED] – Line Feed.............................66
6.2.3.8 [138 DELAY] – Response Speed.................66
6.2.3.9 [139 ADDRESS] – Port address..................66
6.2.4 [14_] – USB.................................................66
6.2.4.1 [141 FORMAT] – Data Format.....................66
6.2.4.2 [142 CSUM] – Checksum.............................66
6.2.4.3 [143 CR] – Carriage Return..........................66
6.2.4.4 [144 LFEED] – Line Feed.............................66
6.2.4.5 [145 DELAY] – Response Speed.................66
6.2.4.6 [139 ADDRESS] – Port address..................6
6.2.5 [15_] – Ethernet TCP/IP..............................6
6.2.5.1 [151 FORMAT] – Data Format.....................6
6.2.5.2 [152 IP] – IP Address...................................6
6.2.5.3 [153 ADDRESS] – Device Address.............6
6.2.5.4 [154 SUB MASK] – Subnet Mask................6
6.2.5.5 [155 GATEWAY] – Gateway Address.........6
6.2.5.6 [156 LOCAL P1] – Local Port 1....................6

CONTENTS
6.2.5. [15 LOCAL P2] – Local Port 2....................6
6.2.5.8 [158 LOCAL P3] – Local Port 3....................6
6.2.5.9 [159 DNS] – DNS address...........................6
6.2.5.10 [15A MAC ADR] – MAC Address...............6
6.2.5.11 [15B TIMEOUT] – Idle timeout...................6
6.2.5.12 [15C CR-LF] – CR+LF................................6
6.2.5.13 [15D Delay] – Response speed.................6
6.2.5.14 [15E REMOTE IP] – Remote IP Addr........6
6.2.5.15 [15F REMOTE PO] – Remote Port............6
6.2.6 [16_] – Printer.............................................68
6.2.6.1 [161 FORMAT] – Print Format.....................68
6.2.6.2 [162 METHOD] – Print activation.................68
6.2.6.3 [163 PRT MSG] – Display “PRINTING”.......68
6.2.6.4 [164CN] – Print Ticket Number....................68
6.2.6.5 [165 DATE] – Print Date...............................68
6.2.6.6 [166 Time] – Print time.................................68
6.2.6. [16 ID1] – Print ID1.....................................68
6.2.6.8 [168 ID2] – Print ID2.....................................68
6.2. [1 _] – Print Setup......................................68
6.2. .1 [1 1 HEADER1] – Ticket header.................68
6.2. .2 [1 2 HEADER2] – Ticket header.................68
6.2. .3 [1 3 HEADER3] – Ticket header.................68
6.2. .4 [1 4 FOOTER1] – Ticket footer...................68
6.2. .5 [1 5 FOOTER2] – Ticket footer...................68
6.2. .6 [1 6 LF BEFORE] – LF before print.............68
6.2. . [1 LF AFTER] – LF after print...................69
6.2. .8 [1 8 FORM F] – Form feed..........................69
6.2. .9 [1 9 LEFT SP] – Left margin.......................69
6.2. .10 [1 A COPY] – Left margin..........................69
6.2.8 [18_] – Barcode/ID Setup...........................69
6.2.8.1 [181 STX] – STX..........................................69
6.2.8.2 [182 PREFIX] – Prfix discard.......................69
6.2.8.3 [183 LENGTH] – Data length.......................69
6.2.8.4 [184 AUTOSAVE] – Auto-save data............69
6.2.9 [19_] – Option Card.....................................69
6.2.9.1 [19_] – Analogue output...............................69
6.2.9.2 [19_] – Ethernet TCP/IP............................... 0
6.2.9.3 [19_] – PROFIBUS....................................... 0
6.2.9.4 [19_] – PROFINET, Ethernet/IP................... 0
6.2.9.5 [19_] – CANopen.......................................... 0
6.2.9.6 [19_] – Ethercat............................................ 0
6.2.9. [19_] – CC-Link............................................. 0
6.2.9.8 [19_] – Powerlink.......................................... 1
6.3 [2--] – CONFIGURATION PARAMETERS.......... 1
6.3.1 [21_] – Display and Sound.......................... 1
6.3.1.1 [211 LIGHT] – Backlight............................... 1
6.3.1.2 [212 COLOR] – Backlight colour.................. 1
6.3.1.3 [213 KEYSOUN] – Key sound..................... 1
6.3.1.4 [214 REFRESH] – Refresh rate................... 1
6.3.2 [22_] – Information display.......................... 1
6.3.2.1 [221 TIME] – Weighing Mode....................... 1
6.3.2.2 [222 DATA] – Informative data..................... 1
6.3.3 [23_] – Startup............................................ 2
6.3.3.1 [231 TARING] – Tare mode......................... 2
6.3.3.2 [232 AUTOT] – Auto Tare............................ 2
6.3.3.3 [233 AUTO CLR] – Auto Tare Clear............ 2
6.3.3.4 [234 PWR TARE] – Save Tare.................... 2
6.3.3.5 [235 Filter] – Adaptive filter.......................... 2
6.3.3.6 [236 LANGUAGE] – Language.................... 2
6.3.4 [24_] – Function keys.................................. 2
6.3.4.1 [241 */PCS KEY] – <☼>, <PCS> function... 2
6.3.4.2 [242 Δ/APW KEY] – <Δ>, <APW> function. 2
6.3.4.3 [243 ID2/* KEY] – <ID2>, <☼> function....... 2
6.3.4.4 [244 RGHT IR] – <IRR> function................. 3
6.3.4.5 [245 LEFT IR] – <IRL> function................... 3
6.3.5 [25_] – Initial data entry.............................. 3
6.3.5.1 [251 DATE] – Date format............................ 3
6.3.5.2 [252 Date set] – Date setting....................... 3
6.3.5.3 [253 TIME SET] – Time setting.................... 3
6.3.5.4 [254 CN] – Ticket number............................ 3
6.3.5.5 [255 S.NAME] – Scale name....................... 3
6.3.6 [26_] – Passwords...................................... 3
6.3.6.1 [261 KEY LOCK] – Keys password............. 3
6.3.6.2 [262 USER] – User password...................... 3
6.3.6.3 [263 SERVICE] – Service password............ 3
6.4 [3--] – APPLICATION PARAMETERS................. 3
6.4.1 [31_] – EzAz smart applications................. 3
6.4.1.1 [311 APPLICA] – EzAz application.............. 3
6.4.1.2 [312 LIMITS] – Limit mode........................... 4
6.4.1.3 [313 INFODIS] – Information display........... 4
6.4.1.4 [314 DISPLAY] – Auxiliary display............... 4
6.4.1.5 [315 Colors] – Backlight colours.................. 4
6.4.1.6 [316 CHANGE] – Backlight change............. 4
6.4.1. [31 ACOUSTI] – Warning sound................ 4
6.4.2 [32_] – EzAz Use partameters.................... 4
6.4.2.1 [321 START] – Starting the application....... 4
6.4.2.2 [322 FILLING] – Filling mode....................... 4
6.4.2.3 [323 STAREDELA] – Delay auto-tare.......... 4
6.4.2.4 [324 TOTAL] – Totalling mode..................... 4
6.4.2.5 [325 GT ERASE] – Grand Total erase......... 4
6.4.2.6 [326 OUTPUTS] – Output relay switching... 4
6.4.3 [33_] – Dynamic in motion Weighing.......... 4
6.4.3.1 [331 OPERATE] – Dynamic start................. 5
6.4.3.2 [332 FILTER] – Dynamic filter...................... 5
6.4.4 [34_] – Key locking..................................... 5
6.4.4.1 [341 ON/OFF]............................................... 5
6.4.4.2 [342 ID1, DATE]........................................... 5
6.4.4.3 [343 ID2, ☼, G/N]......................................... 5
6.4.4.4 [344 M+, SP]................................................. 5
6.4.4.5 [345 MRC, PRINT]....................................... 5
6.4.4.6 [346 ☼, PCS, UNIT]..................................... 5
6.4.4. [34 Δ, APW, HIGHRE]................................ 5
6.4.4.8 [348 TARE]................................................... 5
6.4.4.9 [349 SET/CLR]............................................. 5
6.4.4.10 [34A ZEROING].......................................... 5
6.4.4.11 [34B ENTER].............................................. 5
6.4.4.12 [34C NUMERIC]......................................... 5
6.4.4.13 [34D RGHT IR]........................................... 5
6.4.4.14 [34E LEFT IR]............................................. 5
6.4.5 [35_] – Digital inputs................................... 5
6.4.5.1 [351 INPUT 1] – Input 1 function.................. 5
6.4.5.2 [352 INPUT 2] – Input 2 function.................. 6
6.4.5.3 [353 INPUT 3] – Input 3 function.................. 6
6.4.5.4 [354 INPUT 4] – Input 4 function.................. 6
6.4.6 [36_] – Digital outputs................................. 6
6.4.6.1 [361 OUPUT 1] – Output 1 function............. 6
6.4.6.2 [362 OUPUT 2] – Output 2 function............. 6
6.4.6.3 [363 OUPUT 3] – Output 3 function............. 6
6.4.6.4 [364 OUPUT 4] – Output 4 function............. 6
6.4.6.5 [365 OUPUT 5] – Output 5 function............. 6
6.4.6.6 [366 ZR [d]] – In-Zero range.........................
6.4.6. [36 OUPUTS IMME] – Output relay mode.
6.4. [3 _] – Identification data............................
6.4. .1 [3 1 NAMEDIS] – ID name display..............
6.4. .2 [3 2 ID1NAME] – ID 1 data name...............
6.4. .3 [3 3 ID1LINK] – Data linked to ID1..............
6.4. .4 [3 4 ID2 NAME] – ID2 data name...............
6.4. .5 [3 5 ID2 LINK] – Data linked to ID2.............
6.5 [5--] – SCALE PARAMETERS............................. 8
6.5.1 [51_] – Scale Setup.................................... 8
6.5.1.1 [511 APROVAL] – Approved/Industrial........ 8
6.5.1.2 [512 HIGHRES] – Hi-Res operation............. 8
6.5.1.3 [513 PWR ZERO] – Zero at power on......... 8
6.5.1.4 [514 ZEROING] – Zero key range............... 8
6.5.1.5 [515 AZTRACK] – Auto. Zero tracking......... 8
6.5.1.6 [516 STABLE] – Stability band..................... 8
6.5.1. [51 STBTIME] – Stability time.................... 8
6.5.1.8 [518 MIN TARE] – Min. Auto-Tare............... 8
6.5.1.9 [519 MINWEIGT] – Min. weight for print...... 8
6.5.1.10 [51A TILT] – Tilt switch.............................. 8
6.5.2 [52_] – Scale Build...................................... 8
6.5.2.1 [521 UNIT] – Weight units............................ 8
6.5.2.2 [522 RANGE] – Single/Multi range.............. 9
6.5.2.3 [523 MAX] – Capacity/Division..................... 9
6.5.2.4 [524 OVER] – Over range............................ 9
6.6 [6--] – CALIBRATE/ADJUST............................... 9
6.6.1 [61_] – Calibration....................................... 9
6.6.1.1 [611 TEST WEIGHT] – With weight............. 9
6.6.1.2 [612 LINEARIZATIO] – Linearisation........... 9
6.6.1.3 [613 ELECTRONIC] – vCal..........................80
6.6.2 [62_] – Adjustment......................................80
6.6.2.1 [621 ZERO ADJUSTM] – Adjust zero..........81
6.6.2.2 [622 SPAN ADJUSTM] – Adjust span.........81
6.6.2.3 [623 S UNDER LOAD] – Adj. Span loaded. 81
6.6.2.4 [624 GRAVITY CAL] – Calibration gravity...81
6.6.2.5 [625 GRAVITY USAG] – Installed gravity....81
6.6.3 [63_] – Coefficients.....................................81
6.6.3.1 [631 TEST WEIGHT] – Calibration weight...81
6.6.3.2 [632 ZERO COEFFIC] – Zero coeficient.....81
6.6.3.3 [633 GAIN COEFFIC] – Over range............82

CONTENTS
6. [8--] – METROLOGY PARAMETERS..................82
6. .1 [81_] – Alibi memory...................................82
6. .1.1 [811 ALIBI] – Enable memory......................82
6. .1.2 [812 ACCESS] – Access a record...............82
6. .1.3 [813 TRANSFER] – Transfer records..........82
6. .1.4 [814 ALIBI INFO] – Alibi information............82
6. .1.5 [815 FORMAT] – Format memory...............82
6. .2 [82_] – Information......................................82
6. .2.1 [821 CAL COUNTER] – Calibrn. counter.....83
6. .2.2 [822 CONFIG COUNT] – Config. counter....83
6. .2.3 [823 NEXT VERIFIC] – Next verification.....83
6.8 [9--] – DIAGNOSTIC PARAMETERS..................83
6.8.1 [91_] – Hardware test..................................83
6.8.1.1 [911 KEY] – Test keypad.............................83
6.8.1.2 [912 RS232-1] – Test RS232-1....................83
6.8.1.3 [913 RS232-2] – Test RS232-2....................83
6.8.1.4 [914 RS485] – Test RS485..........................83
6.8.1.5 [915 USB] – Test USB.................................83
6.8.1.6 [916 IN/OUT] – Test digital I/O.....................83
6.8.1. [91 DISPLAY] – Test display......................83
6.8.1.8 [918 LC SIGNAL mV] – Test LC signal........83
6.8.1.9 [919 PRINTER] – Test Printer......................83
6.8.1.10 [91A ID DEVICE] – Test ID device............83
6.8.2 [92_] – History.............................................84
6.8.2.1 [921 PEAK LOAD] – Peak loads..................84
6.8.2.2 [922 UNDER LOGS] – Under load errors....84
6.8.2.3 [923 ERROR LOGS] – Error logs................84
6.8.2.4 [924 ENTRY LOGS] – Access logs.............84
6.8.3 [9 _] – Firmware.........................................84
6.8.3.1 [9 1 INSTRUMENT] – Firmware version.....84
6.8.3.2 [9 2 OPTION] – Firmware option................84
6.8.3.3 [9 3 UPGRADE] – Firmware upgrade.........84
6.8.4 [99_] – Defaults...........................................84
6.8.4.1 [993 PARAMET DEF] – Default params......84
6.8.4.2 [994 FACTORY DEF] – Factory defaults.....84
TROUBLE SHOOTING................................................85
.1 ERRORS.............................................................85
.2 QUESTIONS AND ANSWERS............................8
.3 ADDITIONAL RESOURCES...............................8
8 SECURING BY SEALING............................................88
9 CONFORMITY.............................................................89
10 APPENDIX.................................................................90
10.1 FITTING OPTION CARDS................................90
10.2 MODBUS OPTION............................................92
10.3 PROFIBUS OPTION..........................................93
10.4 PROFINET OPTION..........................................99
10.5 ETHERNET/IP OPTION..................................106
10.6 ETHERNET OPTION.......................................115
10. CANOPEN OPTION........................................116
Always check the PT web site for the most up to date information and revisions
www.ptglobal.com

www.ptglobal.com PT610, PT620, PT630 Instruction Manual 1
1 NOTI ES
1.1 SAFETY
AUTION! READ THIS MANUAL BEFORE OPERATING OR SERVICING THIS EQUIPMENT.
FOLLOW THESE INSTRUCTIONS CAREFULLY. SAVE THIS MANUAL FOR FUTURE
REFERENCE. DO NOT ALLOW UNTRAINED PERSONNEL TO OPERATE, CLEAN,
INSPECT, MAINTAIN, SERVICE, OR TAMPER WITH THIS EQUIPMENT. ALWAYS
DISCONNECT THIS EQUIPMENT FROM THE POWER SOURCE BEFORE CLEANING OR
PERFORMING MAINTENANCE. CALL PT LIMITED FOR PARTS, INFORMATION, AND
SERVICE.
WARNING! ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS EQUIPMENT.
EXERCISE CARE WHEN MAKING CHECKS, TESTS AND ADJUSTMENTS THAT MUST BE
MADE WITH POWER ON. FAILING TO OBSERVE THESE PRECAUTIONS CAN RESULT IN
BODILY HARM.
WARNING! FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD CONNECT TO A
PROPERLY GROUNDED OUTLET ONLY. DO NOT REMOVE THE GROUND PIN.
WARNING! DISCONNECT ALL POWER TO THIS UNIT BEFORE REMOVING ANY
CONNECTION, OPENING THE ENCLOSURE OR SERVICING.
WARNING! BEFORE CONNECTING/DISCONNECTING ANY INTERNAL ELECTRONIC
COMPONENTS OR INTERCONNECTING WIRING BETWEEN ELECTRONIC EQUIPMENT
ALWAYS REMOVE POWER AND WAIT AT LEAST THIRTY (30) SECONDS BEFORE ANY
CONNECTIONS OR DISCONNECTIONS ARE MADE. FAILURE TO OBSERVE THESE
PRECAUTIONS COULD RESULT IN DAMAGE TO OR DESTRUCTION OF THE EQUIPMENT
OR BODILY HARM.
AUTION! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE
DEVICES.
1.2 PRE AUTIONS
•Before using the instrument, check that the supply voltage is correct. If it is not, do not connect the
scale to the power supply.
•Before energising the instrument, check all connectors are installed properly and all external cables
are installed safely to avoid mechanical damage.
•The scale should only be used under suitable environmental conditions as indicated in this manual.
•Do not use this scale in places where conditions are unstable or there is explosive danger.
•Do not place the scale near heat sources or under direct sunlight where it may heat up.
•Keep the scale as far away from other electromagnetic radiation sources as possible, their influence
could affect the weighing accuracy.
Failure to follow these precautions will void warranty, contact your supplier to clarify any questions.
Rights and Liabilities
This publication may not be reproduced in part, stored in a retrieval system, or transmitted in any form or by
any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of PT
Limited.
No patent liability is assumed with respect to the use of the information contained herein. While every
precaution has been taken in the preparation of this manual, PT assumes no responsibility for errors or
omissions. Neither is any liability assumed for damages resulting from the use of the information contained
herein.
The information herein is believed to be both accurate and reliable. PT, however, would be obliged to be
informed if any errors occur. PT cannot accept any liability for direct or indirect damages resulting from the
use of this manual.
PT reserves the right to revise this manual and alter its content without notification at any time.
Neither PT nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses,
costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this
product or unauthorized modifications, repairs, or alterations to this product, or failure to strictly comply with
PT operating and maintenance instructions.
PT shall not be liable against any damages or problems arising from the use of any options or any
consumable products in any way other than in accordance with their standard terms and conditions.
NOTE: The contents of this manual are subject to change without notice.
All rights reserved. Copyright © 2015 by PT Limited, Auckland, New Zealand

www.ptglobal.com PT610, PT620, PT630 Instruction Manual 2
2 DES RIPTION
2.1 INTRODU TION
The PT610, PT620 and PT630 (PT6X0 series) are smart indicators with advanced features for general and
industrial process weighing applications. Powerful PLC integration facilities are available and serial ports
such as RS-232C, RS-485, USB are standard.
A step up from the PT600, the PT610 and PT630 are available with a range of options to connect by various
fieldbus protocols such as Ethernet TCP/IP. Ethernet/IP, Modbus, PROFIBUS, PROFINET, CANopen,
EtherCAT, CC-Link, Powerlink and also along with the PT620 there are options with digital Input/Output and
analogue output.
Powerful calibration options including vCal, Electronic calibration without test weights supporting fast easy
setup and service. The PT6X0 series features adaptive filtering for fast settling, high display resolution and a
speed of up to 800 conversions per second.
It’s small size IP6 stainless steel body is perfect for desk, wall or panel installations and provides a large
display and flexible operator interface.
2.2 STANDARD SUPPLIED ITEMS
The indicator are fitted with mains cable and the following are the items supplied as standard. Please
check the contents of your package before installing and advise PT of any discrepancies.
Indicator PT610, PT620
PT630
All mating connectors for load cell ( way), RS232C (3 way),
RS232C+RS485 (6 way) and mains power (3 way) Included
USB drive with Manual Included
2.3 A ESSORIES SOLD SEPARATELY
The following accessories are available for separate purchase.
•USB cable with sealing gland.
•RS-232C cable with null modem wiring and 9 pin connector for PC connection.
•RS-232C to USB adapter.
•RS485 cable with USB plug for PC connection.
•Wall/desk mounting bracket.
•Column/pole mounting bracket.
•Swivelling 2D wall mounting bracket.
•Load cells, cable and junction boxes are available on the PT web site.
As well as the above accessories, the following options are available for separate purchase.
Refer to the table below to verify compatibility with the specific indicator model.
•Analogue output.
•Digital input (opto-isolated), relay output.
•Alibi memory for recording and recalling printed weigh data.
•Modbus software for onboard ports.
•Fieldbus option cards (Ethernet (TCP/IP) interface, PROFIBUS DPV1 interface + 4 Input/5
Relay Output, PROFINET interface + 4 Input/5 Relay Output, Ethernet/IP interface + 4 Input/5
Relay Output, CANopen interface + 4 Input/5 Relay Output, EtherCAT interface + 4 Input/5
Relay Output, CC-Link interface + 4 Input/5 Relay Output, Powerlink interface + 4 Input/5 Relay
Output).
•Scale input card for optional attachment of a second scale.

www.ptglobal.com PT610, PT620, PT630 Instruction Manual
3
2.4 MODELS and FEATURES
Features\Models
Desk Mount PT610DM PT620DM PT630DM
Wall Mount PT610WM PT620WM PT630WM
Panel Mount PT610PM PT620PM PT630PM
Touch Free IR Keys (2 Keys) n/a n/a Yes
Ethernet (TCP/IP) interface O1 n/a
Modbus (RTU /TCP) O n/a O
PROFIBUS DPV1 interface + 4 Input/5 Relay Output O1 n/a O1
PROFINET interface + 4 Input/5 Relay Output
Ethernet/IP interface + 4 Input/5 Relay Output
CANopen interface + 4 Input/5 Relay Output
EtherCAT interface + 4 Input/5 Relay Output
CC-Link interface + 4 Input/5 Relay Output
Powerlink interface + 4 Input/5 Relay Output
2 Platform weighing n/a n/a O
BSI data interface (BSI-PRO command set) n/a Yes
Classifying by weight
Check-weighing
Filling
Dynamic/Animal weighing
Piece Counting
Weight Totalling
Piece Totalling
Pre-Tare entry
Pre-Tare value storage (500 values)
ID data (ID1, 500 records for stored items)
ID Data (ID2, second set 500 records)
Average Piece Weight storage for counting (500 values)
Alibi Memory (999999 records) O
Dynamic/Unstable load weighing Yes
Setpoint storage (500 sets)
Unit selection (g, kg, t, lb, oz)
Unit Switching (kg/lb, g/oz)
O = Option. O1 = Only one Option can be installed at a time.
Features\Models
Desk Mount PT610DM PT620DM PT630DM
Wall Mount PT610WM PT620WM PT630WM
Panel Mount PT610PM PT620PM PT630PM
Docket Printing
Yes
Label Printing (with Barcode2)
Auto-zero tracking and auto-zero at power-up
Motion detection
Adaptive digital filter for faster measuring
Electronic calibration (vCal) without test weights
Electronic calibration (vCal) over field bus
Zeroing and Taring via fieldbus
Zero and Span calibrations over field bus
Zero adjustment without span change
Span adjustment with test weights
Span adjustment without unloading the scale
3 point calibration (linearity correction)
Programming by PT AzCom PC software
8 load cells 350 Ω or 16 load cells 00 Ω
100 – 240 VAC
12 to 28 VDC power supply range
1 000 to 999 999 display resolution
High internal resolution up to 16 000 000 counts
Up to 800 conversion per second
RS-232C Serial interface
RS-232C Second Serial interface
RS-485 Serial interface
USB Serial Interface
BSI data interface (BSI-BASE command set)
Continuous data output
Fast Continuous data output
4 Digital Inputs, 5 relay outputs (DI/O) O1
Analogue output (4–20, 0–20mA,0–5, 0–10VDC)+DI/O
2 = Third party barcode software required. n/a = Not Available

www.ptglobal.com PT610, PT620, PT630 Instruction Manual 4
2.5 DEFINITIONS AND ONVENTIONS
ADC:
Analogue to digital converter, converts the analogue signal into a digital signal.
DAC:
Digital to analogue converter, converts the digital signal to an analogue signal, usually after some digital
signal processing.
Dead weight:
Dead weight is the self weight of the platform or scale load carrying structure on the load cells without
the contents or items to be weighed. The output voltage of the load cell in response to the weight of the
platform is usually the zero offset. The zero offset must be within the range of the instrument adjustment
for correct operation.
Live weight :
The weight that is applied to the scale and shown on the indicator.
Excitation voltage:
The voltage that is supplied by the indicator to the load cell.
Load cell:
Load cell is a device that converts force to electronic voltage. A load cell consists of two parts. The first
part is a sensor that can be linearly distorted according to the force applied to it. The second part is the
strain gauge element which changes its resistance according to the distortion of the sensor.
Load cell rated output:
The output voltage from the load cell divided by the excitation voltage at load cell rated capacity. This is
usually expressed in mV/V.
Input range:
The maximum range of input that the device can accept. This is usually stated in mV and for a full load
cell system is calculated from the number of load cells (Lcn), mV/V (LCmv) and capacity (LCcap) and
also the maximum total load (TL) (including dead load) on the load cells and the excitation voltage (EV).
Input Range (mV) = TL / (LCn * LCcap) * LCmv * EV
Note: A summing box with corner adjustment will reduce this value slightly.
FSO:
Full scale output. Errors may be presented as a % of the full output range after calibration.
PLU
Product Look Up. A code to look up values stored in product information
CLU
Counting Look Up. A code to look up values stored for counting
APW
Average product weight. Used in parts counting, this is the average weight of one piece of product,
determined by weighing a sample and dividing by the number of parts.
ALU
Amount Look Up. A code to look up values stored in memory in relation to the amounts (quantity) of
parts in check weighing.
Span Adjustment
Adjust the indicator so that when the load on the scale is changed the scale correctly shows the same
change.
[001]
Numbers shown in square brackets in bold refer to parameters set during configuration.
[ZEro. A]
Words shown in square brackets in bold refer to prompts shown on the display.
<TARE>
Words shown in angled brackets in bold refer to keys of the keypad. <f>, <G/N>, <TARE>, <ZERO>,

www.ptglobal.com PT610, PT620, PT630 Instruction Manual 5
<PRINT>.
EtherX
EtherX is third party software available from the internet to enable setting of IP address parameters in
the indicators with Ethernet.
AzCom
AzCom is software currently in development for communication and configuration of the PT Azure
Series indicators and controllers.

www.ptglobal.com PT610, PT620, PT630 Instruction Manual 6
3 SPE IFI ATIONS
General common specifications
A/D Converter
A/D converter type 24 bit Delta-Sigma ratiometric with integral analogue and digital filters
Conversion Rate Up to 800 conversions per second.
Input sensitivity 0.4 μV/d (approved); 0.05μV/d (non approved)-5mV to +19mV
Analogue input range -5mV to +19mV
Zero offset adjustment range -5mV to +19mV
Resolution
Display resolution up to 10 000 increments (approved); up to 999 999 increments (industrial)
Internal resolution up to 16 000 000
Non-linearity, temp. coefficient Within 0.0015% FS, < 2 ppm/ºC
Display
Type Wide view angle backlit LCD with 6x 22mm digit height main numerals and
16x 8mm alphanumeric characters. Display of units and status. Bar graph.
Scale, Calibration and Functions
Scale and units Up to 300 000kg, Units g, kg, oz, lb Metric/Imperial switchable
Calibration
Span calibration with weights, even without without zero calibration.
vCal for calibration by direct entry of load cell characteristics.
Temporary zero calibration, Zero adjustment, Gain adjustment
Calibration of span and zero by fieldbus commands.
Digital filter 5 step programmable adaptive digital filter.
Dynamic/Animal weighing
Weighing functions
Tare, zeroing, auto zero track, motion detection, auto-zero at power up, tare
status save at power off, increased resolution, automatic tare and clear,
temporary gross indication, unit change.
Other Functions Pre-settable label (print ticket) count number, gross or tare indication,
storage for 500 sets of setpoints.
Load cells
Excitation 5VDC 125mA
Number of load cells Up to 8 load cells 350Ω, 16 load cells 00Ω, in parallel.
Load cell connection 4 or 6 wire connection. Cable length: maximum 1000 m/mm² for 6-wires
Communication
RS-232 (2x 3 wire) and modes 1200 to 5 600 baud, /8 bit, E/O/N. Command, continuous, Printer, BSI.
RS-485 and modes 1200 to 5 600 baud, /8 bit, E/O/N. Command, continuous, Printer, BSI
output. Up to 31 units on the bus.
USB Standard USB for Mini-B cable (internal on PCB). Command, continuous,
Printer, BSI communications.
Response Speed < 4mS response delay from read/write commands.
Fieldbus/Ethernet Optional. Refer 2.4MODELS and FEATURES table for applicability.
Printing
Format Programmable 1 line or multi-line, print ticket count number can be preset.
Label printing with graphic (3rd party software may be required for graphic)
Print languages English, German, French, Italian, Spanish, Turkish
Digital/Analogue Inputs and Outputs
Optional Refer comparison table for applicability.
Power Connection
All Models Integral cable, 100-240 VAC (100-125VAC with USA plug), 50-60 Hz.
12VDC (12-28) configurable.
Environment and Enclosure
Operating Environment -15ºC to +55ºC; max. 90% RH (80% RH, -10~40ºC approved), non-
condensing. IP6 sealing with pressure equalising port.
Enclosure Stainless steel. Wall type: 260x200x65mm, Desk type: 250x180x85mm,
weight 2.3kg net, 3.2kg gross. Packing size 290x280x210mm.