PT PT 1243 User manual
UNPACKING ARTICLE
1.
PT 1243 host....................................................................1PCS.
2.
Adaptor.............................................................................. 1PCS.
3.
Remote control................................................................. 1PCS.
4.
Audio line............................................................................1PCS.
5.
Microphone........................................................................ 1PCS.
PARAMETER DESCRIPTION
1.
Output power....................................................................... 40W.
2. Battery............................................................. 12V/4.5A.
3.
Input sensitivity........................................................ 450±50MV.
4.
Signal to noise ratio..........................................................75dB.
5.
Input voltage.................................................................... DC15V.
Matters needing attention
1- Read these instructions throughly before using this item.
2- Keep these instructions for future reference.
3- Heed all warnings.
4- Follow all instructions.
5- WARNING: To prevent re or electric shock, do not expose this equipment to rain or moisture. Do not
store or operate this product near any liquids.
6- Clean only with a dry cloth.
7- Do not store or operate this product near any heat sources such as radiators, heat registers, stoves, or
other apparatuses (including ampli ers) that produceheat.
8- Unplug the unit during lightning storms or when unused for long periods oftime.
9- When wiring this unit and all other equipment used in connection to this unit make sure that all of
your equipment is turned OFF.
10- Before placing, installing, rigging, or suspending any product, inspect all hardware, suspension,
cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded,
or non-load rated component could signi cantly reduce the strength of the installation,
placement or array. Any such condition severely reduces the safety of the installation and should
be immediately corrected. Use only hardware which is rated for rated for the loading conditions
of the installation and any possible short-term, unexpected overloading. Never exceed the
rating ofthe hardware or equipment.
11- Refer all servicing to quali ed service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been .
Instruction
HIGH FIDELITY MOBILE BATTERY SPEAKER
MODEL:PT 1243
BEFORE USING PLEASE READ THIS MANUAL CAREFULLY
REAR PANEL DESCRIPTION REMOTE CONTROL DESCRIPTION
1.
DC 12V input
2.Wiref Mic. input jack
3.Mode selection
Long press on Bluetooth
4.Previous song
5.Pause/Play
6.
Next song
7.
Microphone priority switch
Long press is a repeat key
8.
Rec/Recplay
9.Display/receiver
10.EQ adjustment
11.LED Power on/off
12.
Power on/off
13.
Master volume adjustment
4.DC 15V input
15.Treble volume adjustment
16.AUX.audio input
17.Bass volume adjustment
18.Mic.Echo adjustment
19.USB input jack
20.
TF input jack
21.
Mic. volume adjustment
1.Power on/off
2.Mode selection
3.Mute
4.Volume+
5.Next song
6.Pause/Play/Scan
7.Volume-
8.Equalization
9.Program
10.Repeat
11.Previous song
12.Stop song
1
2
345678 9 10
11
12
LED
MIC
MODE PREV PLAY NEXT M.PRI REC
TWS
REPEAT
-
MIC.VOL
+
-
VOLUME
+
63 Hz 400 Hz 1K Hz 6K Hz 10K Hz
M.ECHO BASS TREBLE
- + - + -
+
DC 15V
TF CARD
USB
AUX
21 20 19 18 171615 14
13
12
STOP
MUTE
11
10
1
2
3
4
5
6
7
8
9
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmful
interference to radio or television reception, which can be determined by turning the equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any
changes
or
modifications
to
this
device
not
explicitly
approved
by
manufacturer
could void your authority to operate this equipment.
This
device
complies
with
part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
following
two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
