Puls FPT500.245-062-117 User manual

Headquarters: PULS GmbH, Elektrastr. 6, 81925 Munich, Germany, www.pulspower.com
Germany [phone] France [phone] Austria [phone] Switzerland [phone]
China [phone] North America [phone] Singapore [phone] United Kingdom [phone]
The information in this document is believed to be accurate and reliable and may change without notice.
EN
FPT500.245-062-117Installation Manual
PowerSupply, 3-Phase,24V,500W,
DE
FPT500.245-062-117Installationsanleitung
Stromversorgung,3-Phase,24V, 500W
FR
FPT500.245-062-117Manueld'installation
Alimentation d'Énergie,3-Phase, 24V,500W
ES
FPT500.245-062-117Manualdeinstalación
FuenteDeAlimentación,3-Phase,24V, 500W
IT
FPT500.245-062-117ManualediInstallazione
AlimentazioneElettrica,3-Phase, 24V, 500W
PT
FPT500.245-062-117Manualdeinstalação
FonteDeAlimentação,3-Phase, 24V, 500W
Doc. ID: PU-451.015.48-xxB (2022-04-27-AC2)
Read thisfirst!
English
Vor Inbetriebnahmelesen!
Deutsch
Before operating this device, please read this manual thoroughly and retain this manual for
future reference! This device may only be installed and put into operation by qualified
personnel. Ifdamage or malfunction should occur during operation, immediately turn power
off and send device to the factory for inspection. The device does not contain serviceable
parts. The information presented inthis document is believed to be accurate and reliable and
may change without notice. For any clarifications the English translation will beused.
Bitte lesen Siediese Warnungen und Hinweise sorgfältig durch, bevor Sie das Gerät in Betrieb
nehmen. Bewahren Sie die Anleitung zum Nachlesen auf. Das Gerät darf nur durch
fachkundiges und qualifiziertes Personal installiert werden. Bei Funktionsstörungen oder
Beschädigungen schalten Sie sofort die Versorgungsspannung ab und senden das Gerät zur
Überprüfung ins Werk. Das Gerät beinhaltet keine Servicebauteile. Die angegebenen Daten
dienen allein der Produktbeschreibung und sind nicht als zugesicherte Eigenschaften im
Rechtssinne aufzufassen. Im Zweifelsfall giltder englische Text.
Risk of electrical shock, fire, personal injury, or death:
Missachtung nachfolgender Punktekann einen elektrischen
Schlag, Brände, schwere Unfälle oder Tod zur Folgehaben:
- Turn power off before working on the device. Protect against inadvertent re-powering.
- Do not open, modify or repair the device.
- Do not touch during power-on and immediately after power-off. Hot surfaces may cause
burns.
- Schalten Sie die Eingangsspannung vor Installations-, Wartungs- oder Änderungsarbeiten
ab und sichern Sie diese gegen unbeabsichtigtes Wiedereinschalten.
- Führen Siekeine Änderungen oder Reparaturversuche am Gerät durch. Gerät nicht öffnen!
- Gehäuse nicht während des Betriebes oder kurz nach dem Abschalten berühren. Heiße
Oberflächen können Verletzungen verursachen.
A lire avant misesoustension!
Français
Leaprimero!
Español
Veuillez lire ces instructions de montage et d'entretien avant de mettre l'alimentation sous
tension. Conservez cemanuel qui vous sera toujours utile. Cette alimentation ne doit être
installée quepar du personnel qualifié et compétent. En cas de dommage ou
dysfonctionnement, coupez immédiatement la tension d’alimentation et retournez l’appareil à
l’usine pour vérification. ! L’alimentation ne contient pas de pièces échangeables Les
données indiquées dans ce document servent uniquement àdonner une description du
produit et n'ont aucune valeur juridique. En cas de divergences, letexte anglais fait foi.
Conserve este manual como referencia para futuras consultas. La fuente de alimentación solo
puede ser instalada y puesta en funcionamiento por personal cualificado. Por favor lea
detenidamente este manual antes de conectar lafuente de alimentación. Si seproduce un fallo
o mal funcionamiento durante laoperación, desconecte inmediatamente la tensión de
alimentación. En ambos casos, el equipo debe ser inspeccionado en fábrica. La información
presentada en este documento es exacta y fiable en cuanto a ladescripción del producto y
puede cambiar sin aviso. En casa de duda, prevalece el texto inglés.
Prendre en compte les points suivants, afin
d'éviter toutedétérioration électrique, incendie,
dommage aux personnes ou mort:
Riesgo de descarga eléctrica, incendio, accidente grave
o muerte:
- Mettre l’alimentation hors tension avant toute intervention sur celle-ci et s'assurer qu'il n'y
a pas risquede redémarrage.
- Ne pas ouvrir, modifier ou réparer l'alimentation.
- Ne pas toucher le carter pendant le fonctionnement ou directement après lamise hors
tension. Surface chaude risquant d’entraîner des blessures.
- Desconectar la tensión de red antes de trabajar en la fuente de alimentación. Evite una
posible reconexión involuntaria.
- No realizar ninguna modificación o reparación de la unidad. No abrir launidad.
- No tocar durante el funcionamiento ni inmediatamente después del apagado. El calor de la
superficie puede causar quemaduras graves.
Leggereprimaquestaparte!
Italiano
Leiaprimeiro!
Portuguès
Prima di collegareil sistema di alimentazione elettrica si prega di leggereattentamente le
seguenti avvertenze. Conservare leistruzioni per laconsultazione futura. Il sistema di
alimentazione elettrica deve essere installato soloda personale competente e qualificato. Se
durante il funzionamento si verificano anomalie o guasti, scollegareimmediatamente la
tensione di alimentazione. In entrambi i casi è necessario far controllare l'apparecchio dal
produttore! I dati sono indicati solo a scopo descrittivo del prodotto e non vanno considerati
come caratteristiche garantite dell'apparecchio. In caso di differenze o problemi è valido il
testo inglese
Recomendamos aleitura cuidadosa das seguintes advertências e observações, antes de
colocar em funcionamento a fonte de alimentação. Guarde as Instruções para futura consulta,
em casos de dúvida. A fonte de alimentação deverá ser instalada apenas por profissionais da
área, tecnicamente qualificados. Se por acaso, durante a utilização ocorrer algum defeito de
funcionamento ou dano, desligue imediatamente a tensão de alimentação. Em ambos os
casos, será necessária uma verificação na Fábrica! Os dados mencionados têm como
finalidade somente a descrição do produto, e não devem ser interpretados como propriedades
garantidas no sentido jurídico. Em caso de duvidas aplica-se otexto em inglês.
Il mancato rispetto delle seguenti norme può
provocare folgorazione elettrica, incendi, gravi
incidenti e perfino la morte:
A não observância ou o incumprimento dos pontosa seguir
mencionados, poderá causar uma descarga elétrica, incêndios,
acidentes graves ou morte:
- Prima di eseguire interventi di installazione, di manutenzione o di modifica scollegare la
tensione di rete ed adottare tutti i provvedimenti necessari per impedirne il ricollegamento
non intenzionale.
- Non tentare di aprire, di modificare o di riparare da soli l'apparecchio.
- Non toccare quando acceso e subito dopo lo spegnimento. La superficie calda può
causare scottature.
- Antes de trabalhos de instalação, manutenção ou modificação, desligue a tensão de
alimentação, protegendo-a contra uma nova ligação involuntária.
- Não efectue nenhuma modificação ou tentativa de reparação no aparelho. Quando
necessário contacte o seu distribuidor. Não abra o aparelho.
- Não tocar enquanto estiver em funcionamento, nem após a desligar. A superficie poderá
estar quente eprovocar lesões.

EN
FPT500.245-062-117Installation Manual
Product Description
The FPT500.245-062-117 is a stand-alone power supply for three-phase mains systems, which
provides a stabilized and galvanically separated PELV/ES1 output voltage at 4 outputs.
The negative potential of the outputs is permanently connected toPE within the unit.
The housing is rated as IP65 and IP67 according IEC60529 and provides protection against electrical,
mechanical and fire hazards.
The device is equipped with an IO-Link Interface V1.1 to parameterize and access data.
Intended Use
This indoor use device is intended for commercial use, such as in industrial control, process control,
monitoring, measurement or the like. Do not use this device in equipment, where malfunctioning may
cause severe personal injury or threaten human life, without additional appropriate safety devices, that
are suited forthe end-application.
If used in a manner outside of its specification, the protection provided by the device may be impaired.
Installation Instructions
Installthe device with the terminals on the bottom of the device. Other mounting orientations require a
reduction in output current. When installing watch out for the risk of injury from sharp edges and
assure that when installed any sharp edges on the back cannot be accessed and cannot cause injury.
Use4 screws ( 2 on top and 2 on bottom mounting holes) suitable for the underground and a strength
comparable to M4 or UNC 8-32 screws.
The device is designed for pollution degree 3 areas in controlled environments.
The enclosure of the device provides a degree of ingress protectionof IP65 and IP67 when installed
withall mating connectors firmly connected. Assure that during installation no moisture or dirt gets into
the connections. Operation in areas where moisture or condensation can be expected is possible.
The device is designed as "Class of Protection I" equipment according to IEC 61140. Do not use
without a proper PE (ProtectiveEarth) connection.
For TN,TT mains systems with earthed neutral and IT star mains systems with insulation monitoring
the deviceis designed for overvoltage category III zones up to 2000m (6560ft) and for overvoltage
category II zones up to 5000m (16400ft). For TN, TT, IT delta mains systems or ITstar mains systems
without insulation monitoring the device is intended for overvoltage category II zones up to 2000m
(6560ft).
The device is designed to be safe in case of a single phase loss and does not require an external
protection.
The device is designed for convection cooling without a fan. Do not obstruct airflow.
The device is designed for altitudes up to5000m (16400ft). Above 2000m (6560ft) a reduction in
output current is required and the operation is limited according themains systems description above.
Keep the following minimum installation clearances: 50mm on top and bottom, 10mm on the front, the
left and the right side.
The device is designed, tested and approved for branch circuits up to20A (UL) and 32A (IEC) without
additional protection device. If an external fuse is utilized, do not use circuit breakers smaller than6A
B- or C-characteristic to avoid a nuisance tripping of the circuit breaker.
Makesure that you only use plugs and cables rated for the device output current and the required
temperature range. Follow all local and national codes for installation.
Do not connect outputs or devices in parallel for higher output currents.
Do not connect the negative potential of any output to PE.
The maximum permissible ambient air temperature is +70°C (+158°F). The operational temperature is
the sameas the ambient or ambient air temperatureand is defined 2cm below the device.
Cleaning only with a damp cloth.
Functional Description
The output is electronically protected against no-load, overload and short circuit and can supply any
kind of loads, including inductive and capacitive loads. If capacitors with a capacitance >20mF are
connected to one output, this output might switch off after turning the unit or the output on or
connecting the load.
Do not apply return voltages from the load to the output terminals higher than 35V. Feed-back energy
from a load must be below 2.5J.
The green Status LED reports an output above 90% of the adjusted voltage of a running device and
no output tripped due to overcurrent or overtemperature and all three phase voltages are present.
The device has an internal overtemperature protection. If the temperature is too high theunit shuts
down and starts automatically again after cooling off. Each output will get the same state as before
the shutdown.
In case of an internal defect, a redundant circuit limits the maximum output voltage to 32.5V. The
output shuts down and automatically attempts to restart.
IO-Link gives access to internally measured parameters and can be used tochange settings. For
IODD files and additional descriptions please visit www.pulspower.com.
LED bargraph and push-buttons:
The LED bar normally displays the actual output power as percentage value. 100% equals an output
power of 500W. LEDs up to and including 100% are green, the LEDs above 100% are orange. With
pressing theup / down buttons youcan see thepercentage of each output. The orange LED indicates
the selected output.
If you press the "Set Mode" button for 3 seconds all LEDs light up briefly and one LED stays on,
showing theactual output voltage. Withpressing the up or down button you canchange the set
voltage tothe values indicated by the green LED. All orange LEDs are dark. The voltage is set
immediately and the value stored until the next change. If you press the "Set Mode" button again you
can set the output current limit for the selected channel indicated by the orange LED. With the up /
down buttons the current limit is changed to the values indicated by the single lit green LED. The value
is stored until the next change. Select other outputs with the “Set Mode” button. Without further
pressing of push-buttons, the LED bar will return from any other mode to normal mode after 15s. With
the buttons at each channel the channel can turned on/off manually by pressing for at least 1s.
Mating connectors:
Usea standard M12 S-coded female plug toconnect to the input voltage connector (X1).
Pin assignment: Pin 1 for L1, Pin 2 for L2, Pin 3 for L3; Pin PE for PE.
Usea standard M12 A-coded 5 pin female plug for the IO Link.
Use 5 Pin 7/8” male plugs for the output voltage connectors (X3, X4).
Pin assignment: Pin 4 for plus out(1,3); Pin 2 for minus out(1,3); Pin 5 for plus out(2,4); Pin 1 for minus
out(2,4); Pin 3 for FE(functional earth).
Technical Data
All values are typical figures specified at 3x 400Vac 50Hz input voltage,
symmetrical phase voltages, 24V, 500W output load, 25°C ambient
temperature and after a 5 minutes run-in time unless otherwise noted.
Output voltage
DC 24V
Nominal
Adjustment range
24 –28Vdc
Factory setting 24.5V
Output power
Continuous:
600W
At +45°C ambient
500W
At +55°C ambient
350W
At +70°C ambient
Short-term, up to 5s:
1000W
Below +55°C ambient
700W
At +70°C ambient
Derate linearly between +45°C and +70°C
Output currents
Settable per output; up to 10A
Input voltage AC
3AC 380 - 480V
±15%
Mains frequency
50 –60Hz
±6%
Input current AC
0.8 / 0.66A
At 3x400 / 480Vac
Power factor
0.94 / 0.95
At 3x400 / 480Vac
Input inrush current
1.9 / 1.8A peak
At 3x400 / 480Vac,
temp. independent
Efficiency
95.8 / 95.6%
At 3x400 / 480Vac
Losses
22.0 / 23.0W
At 3x400 / 480Vac
Hold-up time
24 / 24ms
At 3x400 / 480Vac
Temperature range
-25 to +70°C
Size (WxHxD)
181x183x59mm
Without connectors
Weight
1200g / 2.7lb
Functional Diagram
Output Characteristic per output
Temperature Range
Allowed output power
Ambient temperature
0-25 0 +70°C
600W
700W
+45
1000W
350W
B
A: continuous
B: short term (max. 5s)
A
+55
500W
Hole Pattern for Mounting
All dimensions inmm / Connectors X1 to.X4 from left to right