CHARGING THE DEVICE
• IMPORTANT: You will need to fully charge your Pulsar APX
Pro Vape prior to use. Allow approximately 3 hours for the
rstfullcharge.NEVERchargethedeviceformorethan24
hours. Allow approximately 1.5 hours for additional re-charges.
• A 5V/1.5 Amp USB AC wall adapter is required for charging
the device. Using the included USB charge cord, set the
Pulsar APX Pro Vape on its side while charging. Do not let
the unit dangle from the cord. This puts pressure on the
charger plug which can result in the unit not charging fully.
It is also recommended to NEVER charge the device from
an automobile power source. Failure to follow warnings
contained within this manual can result in property damage
or personal injury and may void the warranty.
• The battery symbol will show on the screen when a
charging connection is made. The battery symbol will be
full when the battery is charged.
• The device will deliver approximately 1.5 hours of
continuous power, depending on use.
• Battery power level display:
HOW TO USE
2.Forbestresults,llthechamberwithgroundmaterial
halfway to three-quarters full. Use the On Board Stir Stick with
the tamping end to lightly and neatly pack the chamber. Do
not pack too tightly. This allows for even heat distribution
and makes it easier to stir throughout the vape session.
3. Once loaded, replace the mouthpiece and turn the unit on
by pressing the power button rapidly 5 times (5 Clicks for
ON/OFF).
4. The Pulsar APX Pro Vape returns to the last set temperature
when powered on. To change the temperature before or
during a session, tap the up or down button until you get to
your desired temperature. Hold down the up or down button
to cycle through the temperatures faster. Release the button
on the desired setting and allow the Pulsar APX Pro Vape to
adjust to the new temperature.
Cash Mode: Hold down the power button and the
chamber temperature will increase by 20 degrees to get the
most out of your session. When you release the button, it will
return to the normal setting.
5. The device will begin heating immediately. The top number
is your selected temperature. The lower number is the actual
temperature of the chamber. When the bottom number
reaches the desired temp the Haptic Feedback feature will
alert you that the Pulsar APX Pro Vape has reached the
desired temperature.
6. Allow the device to continue heating for approximately 5
seconds longer before inhaling. This ensures the herbs in
thechamberareevenlyheated,maximizingefciency.
7. Adjustable Session Timer: With the device on, press and
hold the power button and the up arrow for 2 seconds, then
select between 5 pre-set session timers: 180, 210, 240,
270, or 300 seconds. The default session time is 240
seconds, or 4 minutes.
8. After your session ends, the device will power down and
the haptic feedback will alert you that the session has
ended. You can end the session at any time by pressing
the button 5 times.
PULSAR PRO TIPS
• Occasionally stir herbs and allow the chamber to reheat for
5 seconds between each inhale.
•Tomaximizeefciency,wheneverpossible,allowtheunitto
cool completely.
• Be sure to turn the unit off when you are done to preserve
the material.
CLEANING INSTRUCTIONS
1. Remove the mouthpiece.
2. Tap out the material from the chamber or use the On Board
Stir Stick to remove.
3. Use the included cleaning brush to sweep the remaining
residue from the chamber.
4. A cotton swab and isopropyl alcohol can be used to clean
stubborn residue. Do not pour alcohol directly into the
chamber. Allow the chamber to fully air dry before use.
5. Pull the silicone off the bottom of the mouthpiece and place
the small silver screen and ceramic airpath into alcohol to
clean any build up. You can also use alcohol and a cotton
swab to remove stubborn build up. Once clean, allow all
parts to air dry before reassembly.
6. Put the mouthpiece back onto the body and the device is
now ready for storage or use.
Thank you for purchasing the Pulsar®APX Pro Vape!
In order to ensure safe use, please read all instructions
and safety warnings before operating. Failure to follow
instructions may result in injury and may void your warranty.
POWER
BUTTON
OLED
DISPLAY
TEMPERATURE
ADJUST
ON BOARD
STIR STICK
ISOLATED
AIRPATH
ERGONOMIC
MOUTHPIECE
1. With the Pulsar APX Pro Vape upright and
the button facing you, lightly pull on the
mouthpiece towards you until it is released.
100-75% 75-50% 25-10%50-25% Less than
10% power
level, please
charge
Low Battery: An empty battery symbol will flash
on the screen when the device will not power on.
