Pulsar HPSB 3512B User manual

HPSB 3512B
v.1.0
HPSB 13,8V/3A/7Ah
Buffer, switch mode power supply unit.
EN**
Edition: 1 from 19.02.2016
Supercedes the edition: ----------

www.pulsar.pl HPSB3512B GREEN POWER
2
Features:
DC 13,8V/3A uninterruptible power supply*
fitting battery: 7Ah/12V
wide range of mains supply: 176÷264V
high efficiency 76%
battery charging and maintenance control
excessive discharging (UVP) protection
battery charge current 0,5A
battery output full protection against short-
circuit and reverse polarity connection
LED indication
protections:
SCP short-circuit protection
OVP overvoltage protection
overvoltage protection (input AC)
against sabotage
overload protection (OLP)
warranty –2 year from the production date
CONTENTS:
1. Technical description.
1.1 General description
1.2 Block diagram
1.3 Description of elements and connectors of the PSU
1.4 Specifications
2. Installation.
2.1 Requirements
2.2 Installation procedure
3. Operating status indication.
3.1 LED indication of operating status
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on)
4.2 Disconnection of discharged battery
4.3 Maintenance
1. Technical description.
1.1 General description.
A buffer PSU intended for uninterrupted supply to devices that require stabilised voltage of 12V DC
(+/-15%). The PSU provides voltage of U=13,8V DC with output current of I=3A + 0,5A for battery charging*.
In case of power decay, a battery back-up is activated immediately. The PSU is constructed based on the switch mode
PSU, with high energy efficiency. The PSU is housed in a metal enclosure (colour RAL 9003) which can accommodate
a 7Ah/12V battery. A micro switch indicates door opening (front cover).
During normal operation, the total current drawn by the equipment may not exceed I = 3A*.
Maximum battery charging current: 0,5A*.
Total device current + battery: 3,5A max*.
The power supply housing has space for additional modules (fuse blocks, voltage regulators and DC-DC
converters). Optional power supply configurations are available at the website: www.pulsar.pl

www.pulsar.pl HPSB3512B GREEN POWER
3
1.2 Block diagram (fig.1).
Fig.1. The block diagram of the PSU.
1.3 Description of PSU components and connectors (tab.1, tab. 2, fig. 2).
Part no.
[Fig. 2]
Description
[1]
PSU module
[2]
connectors (see: tab.2)
[3]
green LED indicates AC power
[4]
P1 potentiometer, output voltage adjustment
[5]
BAT+/GND: battery outputs + BAT=red, - GND=black
[6]
TAMPER, contact, sabotage protection (NC)
[7]
Additional connector for LED indication
Tab.1. The components of the PSU.
Part
[Fig. 2]
Description
L, N
L-N power supply connector
PE
PE protection connector (electric shock protection)
V+
V-
DC supply output
DC supply output (GND)
Tab.2. Output terminals of the PSU.

www.pulsar.pl HPSB3512B GREEN POWER
4
Fig.2. The view of the PSU.
1.4 Specifications:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operation safety (tab.5)
- operating parameters (tab.6)
Electrical parameters (tab. 3)
PSU type
A (EPS - External Power Source)
Mains supply
176÷264V AC
Current up to
0,6A@230VAC
Power frequency
50÷60Hz
Supply power
50W max.
Efficiency
76%
Output voltage
13,8V DC –buffer operation
9,5V÷13,8V DC – battery-powered operation
Output current tAMB<30°C
3A + 0,5A battery charge - refer to chart 1
Output current tAMB=40°C
2,1A + 0,5A battery charge - refer to chart 1
Voltage adjustment range
12÷14VDC
Ripple
120mV p-p max.
Battery charge current
0,5A max. @ 7Ah (± 5%)
Short-circuit protection SCP
electronic, automatic return
Overload protection OLP
105-150% of the PSU power, automatic return
Battery circuit protection SCP and reverse
polarity connection
PTC polymer fuse
Surge protection
varistors
Overvoltage protection OVP
>16V (automatic recovery)
Excessive discharge protection UVP
U<9,5V (± 5%) –disconnect of connection battery
Sabotage protection:
- TAMPER output indicating enclosure opening
- microswitch, NC contacts (enclosure closed),
0,5A@50V DC (max.)
LED indication:
- AC diode indicating AC power status
- AUX diode indicating DC power status at
the PSU output
- red, normal status –on, failure: off
- green, normal status –on, failure: off

www.pulsar.pl HPSB3512B GREEN POWER
5
W
H
D
Mechanical parameters (tab. 4)
Enclosure dimensions
250 x 250 x 80+8 [mm] (WxHxD)
Fixation
See figure 2
Fitting battery
7Ah/12V (SLA) max.
160x90x75mm (WxHxD) max
Net/gross weight
1,8 kg / 2kg
Enclosure
Steel plate DC01, thickness: 0,7mm, colour: RAL 9003
Closing
Cheese head screw (at the front), (lock assembly possible)
Connectors
Power-supply: Φ0,63-2,50 (AWG 22-10)
Outputs: Φ0,63-2,50 (AWG 22-10)
Battery output BAT: 6,3F-2,5
TAMPER output: wires
Notes
The enclosure does not touch the assembly surface so that cables can be led.
Convectional cooling.
Operation safety (tab.5)
Protection class PN-EN 60950-1:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU (I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC
Operating parameters (tab.6)
Operating temperature
-10ºC...+40ºC (see: chart 1)
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
Chart 1. Acceptable output current from the PSU depending on ambient temperature.
2. Installation.
2.1 Requirements.
The buffer PSU shall be mounted by a qualified installer with appropriate permissions and qualifications for
230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall be
mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max. without
condensation) and the temperature from -10°C to +40°C. The PSU shall work in a vertical position that guarantees
sufficient convectional air-flow through ventilating holes of the enclosure.

www.pulsar.pl HPSB3512B GREEN POWER
6
RED LED:
on –the PSU is supplied with 230V AC
off –no 230V AC supply
GREEN LED:
on –DC voltage in the AUX output of the PSU
off –no DC voltage in the AUX output of the PSU
Before installation, prepare a PSU load balance. During normal operation, the total current drawn by
the device may not exceed I=3A*. Maximum battery charge current: 0,5A*. Total device current + battery:
3,5A max*.
As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an
appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed
about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical
system shall follow valid standards and regulations.
2.2 Installation procedure.
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (~230Vac) to L-N clips of the PSU. Connect the ground wire to the clip marked by the
earth symbol PE. Use a three-core cable (with a yellow and green PE protection wire) to make the connection. Lead
the cables to the appropriate clips through the insulating bushing of the connection board.
The shock protection circuit shall be performed with a particular care, i.e. the yellow and green
wire coat of the power cable shall stick to one side of the terminal - marked with ‘ ‘symbol on the
PSU enclosure. Operation of the PSU without the properly made and fully operational shock
protection circuit is UNACCEPTABLE! It can cause a device failure or an electric shock.
4. Connect the power (~230V)
5. Check the PSU output voltage:
- the PSU voltage without load should amount to U=13,8V DC.
6. Connect the battery (mind the colours):
- battery output (+V): BAT+ cable / red,
- battery output (0V): BAT –cable / GND / black.
7. Connect the receivers’ cables to the terminals V+ (+), V-(-) of the PSU module.
8. Check the PSU operation indicator: green LED.
9. After installing and checking proper working, the enclosure can be closed.
3. Operating status indication.
3.1 LED indication of operating status.
The is equipped with two diodes on the front panel:
*Refer to chart 1

www.pulsar.pl HPSB3512B GREEN POWER
7
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on)
In case of overload, the output voltage is automatically shut off, and so is the LED indicator. The restoration
of the voltage takes place immediately after the failure (overload) is over.
4.2 Disconnection of discharged battery.
The PSU is equipped with the discharged battery disconnection system. During the battery-assisted
operation, reducing voltage below 9,5V at the battery terminals will cause battery disconnection.
4.3 Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the
power supply network. The PSU does not require performing any specific maintenance measures, however, in case
of significant dust rate, its interior is recommended to be cleaned with compressed air. In case of fuse replacement,
use a replacement of the same parameters.

www.pulsar.pl HPSB3512B GREEN POWER
8
WEEE MARK
According to the EU WEE Directive –It is required not to dispose of electric or electronic waste as
unsorted municipal waste and to collect such WEEE separately.
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled according
to the applicable law.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [email protected], [email protected]
http:// www.pulsar.pl, www.zasilacze.pl
GENERAL WARRANTY CONDITIONS
1. Pulsar (the manufacturer) grants two-years warranty for the equipment, counted from the device’s production
date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects,
unless such defects have been reported within the warranty period (item 1).
3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main
office of the manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description
of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest
convenienve, however not later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the
repairs, or if the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer,
exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical
agents,
- improper installation and configuration (in defiance with the manual),
9. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined
according to the wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no reponsibility for the defects that result from:
- the damaging, malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to
abide by the recommendations and requirements contained in the manual, or the use of the equipment.