Pulsar HPSB Series User manual

USER MANUAL
EN
Edition: 1 from 24.11.2020
Supersedes the edition:
Power supplies
HPSB series
Buffer switched mode power supply.

www.pulsar.pl HPSB series
2
Features:
supply voltage ~200 –240 V
DC 13,8 V; 27,6 V or 54 V uninterruptible power
supply
available versions with space for 7 Ah –65 Ah
batteries
available versions with current efficiencies
13,8 V: 2A/3A/5A/7A/10A/15A/20A
27,6 V: 2A/3A/5A/7A/10A
54 V: 3A/5A
high efficiency (up to 90%)
battery charging and maintenance control
battery charging current jumper selectable
(models with charging current adjustment)
LED optical indication
deep discharge battery protection (UVP)
battery output protection against short circuit
and reverse connection
protections:
oSCP short-circuit protection
oOLP overload protection
oover voltage protection
osurge protection
oagainst sabotage: unwanted enclosure
opening
warranty –2 years from the production date
TABLE OF CONTENTS:
1. Technical description.
1.1. General description
1.2. Block diagram
1.3. Description of components and connectors
1.4. Specifications
2. Installation.
2.1. Requirements
2.2. Installation procedure
3. Operating status indication.
3.1. Optical indication
4. Maintenance
1. Technical description.
1.1. General description.
Switch mode buffer power supply units HPSB are intended for continuous power supply to devices that require
stabilised voltage of 12, 24 or 48 V DC (±15%).
Displaying parameters of the power supply:
PSU’s name
Output voltage
Output current max.
Charging current
HPSB-12V2A-B
13,8 V
2,5 A
0,5 A
HPSB-12V3A-B
13,8 V
3,5 A
0,5 A
HPSB-12V3A-C
13,8 V
3,5 A
0,5 A
HPSB-12V5A-C
13,8 V
5,5 A
0,5 / 1 A
HPSB-12V7A-C
13,8 V
7 A
1 / 2 A
HPSB-12V10A-C
13,8 V
10 A
1 / 4 A
HPSB-12V15A-D
13,8 V
15 A
2 / 4 A
HPSB-12V20A-E
13,8 V
20 A
2 / 4 / 8 A
HPSB-24V2A-B
27,6 V
2,2 A
0,2 / 0,5 A
HPSB-24V3A-B
27,6 V
3,5 A
0,5 / 1 A
HPSB-24V5A-C
27,6 V
5 A
0,5 / 2 A
HPSB-24V7A-C
27,6 V
7 A
1 / 2 A
HPSB-24V10A-D
27,6 V
10 A
1 / 2 / 4 A
HPSB-48V3A-B
54 V
3 A
0,5 / 1 A
HPSB-48V5A-C
54 V
5 A
0,5 / 1 / 2 A
Total current of the receivers + battery charging current mustn’t cross maximum current of power supply.
In case of power failure, a battery back-up is activated immediately. The PSU is constructed based on the switch
mode PSU, with high energy efficiency. The PSU is housed in a metal enclosure (colour RAL 9003) which can
accommodate a battery (batteries). A micro switch indicates door opening (front cover).

www.pulsar.pl HPSB series
3
1.2. Block diagram (rys.1).
Fig.1. Block diagram of PSU.
1.3. Description of components and connectors.
Table 1. Description of PSU components and connectors (see Fig. 2a, 2b, 2c, 2d, 2e).
Part no.
Description
[1]
LED for DC output voltage
[2]
The potentiometer for output voltage adjustment
[3]
Connector to external LED indicators
[4]
The output of the PSU (V+, V-)
[5]
Battery terminals (B+, B-)
[6]
L-N power supply connector 230V AC, –protection connector
[7]
Selection jumper for charging current:
Power supply units: 12V5A; 12V7A; 12V10A; 12V15A; 24V2A; 24V3A; 24V5A; 24V7A; 48V3A:
IBAT = , IBAT = I1
IBAT = , IBAT = I2
Power supply units: 12V20A; 24V10A; 48V5A:
I1= I2= I3= IBAT = I1
I1= I2= I3= IBAT = I2
I1= I2= I3= IBAT = I3
[8]
Battery fuse
Fig. 2a. View of power supply module (models 12V2A, 12V3A)

www.pulsar.pl HPSB series
4
.
Fig. 2b. View of power supply module (models 12V5A, 12V7A, 24V2A, 24V3A)
Fig. 2c. View of power supply module (models 12V10A, 24V5A, 48V3A)
Fig. 2d. View of power supply module (models 12V15A, 24V7A)
Fig. 2e. View of power supply module (models 12V20A, 24V10A, 48V5A)
Table 2. View of PSU (see Fig. 3).
Element no.
Description
[1]
PSU module
[2]
Cable grommet
[3]
TAMPER; microswitch of antisabotage protection (NC)
[4]
Battery connectors: +BAT = red, - BAT = black

www.pulsar.pl HPSB series
5
Fig.3. View of PSU.
1.4 Specifications:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operation safety (tab.5)
- operating parameters (tab.6)

Table 3. Electrical parameters.
Models
HPSB-12V2A-B
HPSB-12V3A-B
HPSB-12V3A-C
HPSB-12V5A-C
HPSB-12V7A-C
HPSB-12V10A-C
HPSB-12V15A-D
HPSB-12V20A-E
PSU type
A (EPS - External Power Source), II environmental class
Supply voltage
~ 200 - 240 V
Current consumption
0,4 A
0,5 A
0,5 A
0,8 A
1 A
1,3 A
2 A
1,5 A
Power frequency
50/60 Hz
Inrush current
40 A
50 A
60 A
PSU power
35 W
48 W
48 W
76 W
97 W
138 W
207 W
276 W
Output current max.
2,5 A
3,5 A
3,5 A
5,5 A
7 A
10 A
15 A
20 A
Efficiency
87%
87%
87%
87%
87%
87%
87%
86%
Output voltage
11 - 13,8 V –buffer operation
10 - 13,8 V –battery-assisted operation
Adjustment range UAUX
13,5 –14,4 V
Ripple voltage (max.)
100 mV p-p
250 mV p-p
150 mV p-p
Current consumption by
the PSU systems during
battery-assisted operation
40 mA
40 mA
40 mA
15 mA
15 mA
30 mA
30 mA
30 mA
Fitting battery
7Ah
7Ah
17Ah
17Ah
17Ah
17Ah
40Ah
65Ah
Jumper selectable battery
charging current
0,5 A
0,5 A
0,5 A
I1: 0,5 A
I2: 1 A
I1: 1 A
I2: 2 A
I1: 1 A
I2: 4 A
I1: 2 A
I2: 4 A
I1: 2 A
I2: 4 A
I3: 8 A
Net / gross weight
1/1,1 kg
1,3/1,4 kg
1,7/1,8 kg
1,8/1,9 kg
2,3/2,4 kg
2,6/2,7 kg
5/5,6 kg
7/7,8 kg
Battery circuit protection
SCP and reverse polarity
connection
- polymer fuse
(returnable)
- polymer fuse
(returnable)
- polymer fuse
(returnable)
- FBAT fuse (in case of a failure, fuse-element replacement required)
Deep discharge battery
protection UVP
U<9,5 V (± 5%) –disconnection of battery terminal
Optical indication
- LEDs on PCB of power supply unit
- LED indicators on power supply’s cover (see section 3.1)
Tamper protection:
- TAMPER indicates
enclosure opening
- microswitch, NC contacts (enclosure closed),
0,5 A@50 V DC (max.)
Fuses: - FBAT
-
-
-
T 6,3A/250V
F 8A/250V
T 10A/250V
T15A
T20A
Terminals:
Mains supply:
Outputs:
Battery outputs:
TAMPER:
0,5 –2,5 mm2(AWG 26 –12)
Battery wires 6,3F –45cm, angle muffs ML062
Battery wires Ф6 (M6-2,5), 45cm
40cm wires
Notes
convectional cooling
Forced cooling

www.pulsar.pl HPSB series
7
Models
HPSB-24V2A-B
HPSB-24V3A-B
HPSB-24V5A-C
HPSB-24V7A-C
HPSB-24V10A-D
HPSB-48V3A-B
HPSB-48V5A-C
PSU type
A (EPS - External Power Source), II environmental class
Supply voltage
~ 200-240 V
Current consumption
0,8 A
1 A
1,3 A
2 A
1,5 A
1,5 A
1,5 A
Power frequency
50/60 Hz
Inrush current
40 A
50 A
60 A
50 A
60 A
PSU power
61 W
97 W
138 W
194 W
276 W
162 W
270 W
Output current max.
2,2 A
3,5 A
5 A
7 A
10 A
3 A
5 A
Efficiency
90%
87%
90%
88%
87%
90%
87%
Output voltage
22 –27,6 V –buffer operation
20 - 27,6 V –battery-assisted operation
44 - 54 V –buffer operation
40 - 54 V –battery-assisted operation
Adjustment range UAUX
27 –28,8 V
53 –56 V
Ripple voltage (max.)
100 mV p-p
150 mV p-p
Current consumption by
the PSU systems during
battery-assisted operation
15 mA
15 mA
30 mA
30 mA
30 mA
30 mA
30 mA
Fitting battery
2x 7Ah
2x 7Ah
2x 17Ah
2x 17Ah
2x 40Ah
4x 7Ah
4x 17Ah
Jumper selectable battery
charging current
I1: 0,2 A
I2: 0,5 A
I1: 0,5 A
I2: 1 A
I1: 0,5 A
I2: 2 A
I1: 1 A
I2: 2 A
I1: 1 A
I2: 2 A
I3: 4 A
I1: 0,5 A
I2: 1 A
I1: 0,5 A
I2: 1 A
I3: 2 A
Net / gross weight
1,8/1,9 kg
2,3/2,4 kg
5/5,6 kg
5/5,6 kg
7/7,8 kg
5/5,6 kg
7/7,8 kg
Battery circuit protection
SCP and reverse polarity
connection
- FBAT fuse (in case of a failure, fuse-element replacement required)
Deep discharge battery
protection UVP
U<19 V (± 5%) –disconnection of battery terminal
U<38 V (± 5%) –disconnection of battery
terminal
Optical indication
- LEDs on PCB of power supply unit
- LED indicators on power supply’s cover (see section 3.1)
Tamper protection:
- TAMPER indicates
enclosure opening
- microswitch, NC contacts (enclosure closed),
0,5 A@50 V DC (max.)
Fuses: - FBAT
F 3,15A/250V
F 4A/250V
T 6,3A/250V
T7,5A
T10A
F 3,15A/250V
T5A
Terminals:
Mains supply:
Outputs:
Battery outputs:
TAMPER:
0,5 –2,5 mm2(AWG 26 –12)
Battery wires 6,3F –45cm, angle muffs ML062
Battery wires Ф6
(M6-2,5), 45cm
Battery wires 6,3F –45cm,
angle muffs ML062
Wires 40cm
Notes
convectional cooling
Forced cooling
convectional cooling
Forced cooling

Table 4. Mechanical parameters.
HPSB-12V2A-B
HPSB-12V3A-B
HPSB-12V3A-C HPSB-12V5A-C HPSB-24V2A-B
HPSB-12V7A-C HPSB-12V10A-C HPSB-24V3A-B
HPSB-12V15A-D HPSB-24V5A-C HPSB-24V7A-C HPSB-48V3A-B
HPSB-12V20A-E HPSB-24V10A-D HPSB-48V5A-C
Enclosure dimensions
(WxH) [±2mm]
170x180
200x230
230x300
300x300
330x380
460x390
Enclosure dimensions
(W1xH1xD1+D) [±2mm]
175x185x82+8
205x237x82+8
237x305x82+8
305x305
x105+8
335x385x173
+14
465x395x173+
14
Fixing (WxH)
145x152
175x202
205x272
274x265
298x310
425x322
Fitting battery
(WxHxD)
155x100x75
190x100x75
215x172x75
250x172x100
325x178x168
450x190x168
Enclosure
Steel sheet DC01 0,7mm
Steel sheet DC01 1mm
Closing
Cheese head screw (at the front), lock assembly possible
Notes
Enclosure does not adjoin assembly surface so that cables can be led.
Table 5. Operation safety.
Protection class EN 62368-1
I (first)
Degree of Protection EN 60529
IP20
Electrical strength of insulation:
- between input input and output circuits of the PSU
- between input circuit and PE protection circuit
- between output circuit and PE protection circuit
3000 V AC min.
1500 V AC min.
500 V AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500 V DC
Table 6. Operating parameters.
Environmental Class
II
Operating temperature
-10ºC...+40ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
Wg PN-83/T-42106
2. Installation.
2.1 Requirements.
The buffer PSU is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and
required for a given country) for 230 V interference and low-voltage installations. The unit should be mounted in confined
spaces, in accordance with the II-nd environmental class, with normal relative humidity (RH=90% maximum, without
condensing) and temperature from -10°C do +40°C. The PSU shall work in a vertical position that guarantees sufficient
convectional air-flow through ventilating holes of the enclosure.
As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an
appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed
about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical system
shall follow valid standards and regulations.
2.2 Installation procedure.
CAUTION!
Before installation, make sure that the voltage in the 230 V power-supply circuit is cut off.
To switch off power use an external switch in which the distance between the contacts of all poles in
the disconnection state is not less than 3mm.
It is required to install an installation switch with a nominal current of min. 3 A in the power supply circuits
outside the power supply unit.

www.pulsar.pl HPSB series
9
Green LED AC:
on –the PSU is supplied with 230V AC,
off –no 230 V power, battery-assisted operation
Green LED DC:
on –presence of DC voltage in the output of the PSU
off –no voltage in the output of the PSU
Red LED CHARGE:
off –no battery charge
on - battery charging process
1. Mount the PSU in a selected location and connect the wires.
2. Connect the power cables (~230 V) to AC 230 V clips of the transformer. Connect the ground wire to the clip
marked by the earth symbol . Use a three-core cable (with a yellow and green protection wire) to make the
connection. Lead the cables to the appropriate clips of the subplate through the insulating bushing.
The shock protection circuit shall be performed with a particular care, i.e. the yellow and
green wire coat of the power cable shall stick to one side of the ‘ ’ terminal - in the PSU
enclosure. Operation of the PSU without a properly made and fully operational shock
protection circuit is UNACCEPTABLE! It can cause a device failure or an electric shock.
3. Check output voltage and adjust if necessary using potentiometer (see table: displaying parameters of the power
supply).
4. Connect equipment to the appropriate output terminals of power supply (positive connector +V, negative
connector -V).
5. Use the IBAT jumper to set the maximum battery charging current, taking into account the battery parameters.
6. Mount the battery in the battery compartment of the enclosure (Fig. 3). Connect the batteries with the PSU
paying special attention to the correct polarity and type of connections (Fig.4):
a) b) c)
.
Fig. 4 Connecting batteries depending on voltage version of power supply:
a) version 12V, b) version 24V, c) version 48V
7. Switch on the 230 V supply. LEDs on cover of power supply should light (CHARGE diode only during charging).
8. After installing and checking proper working, the enclosure can be closed.
3. Operating status indication.
The power supply unit features LED and acoustic status indication
3.1 Optical indication.
Moreover, PSU is equipped with LED indicating presence of voltage at PSU output, located on PCB of PSU
module.

www.pulsar.pl HPSB series
10
4. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the power
supply network. The PSU does not require performing any specific maintenance measures, however, in the case of
significant dust rate, its interior is recommended to be cleaned with compressed air. In the case of a fuse replacement,
use a replacement of the same parameters.
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment
should be disposed of separately from normal household waste.
CAUTION! The power supply unit is adapted for cooperation with the sealed lead-acid batteries (SLA). After the operation period they must
not be thrown but recycled according to the applicable law.
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
E-mail: [e-mail], [email protected]
http:// www.pulsar.pl, www.zasilacze.pl