Pulsar PS-2002470 User manual

1
PS-2002470
PS 24V/7A enclosed switch mode power supply
Edition: 5 from 27.05.2014
Supersedes edition: 4 from 07.03.2013 EN
Features of the power supply unit:
•
power output 7A/24÷28VDC
*
• wide AC input voltage range 176÷264V
• high efficiency 85%
•LED optical signalisation
•protections:
• SCP short-circuit protection
• overvoltage OVP
• overvoltage protection
• overload (OLP)
•warranty – 2 year from the production date
1. Technical description.
1.1.General description.
The power supply unit is intended for the feeding of alarm system equipments, which require 24V DC supply voltage
and current load I=7A. The design enables simple changing of the output voltage, within the range of 24V÷28V DC, using a
potentiometer. The power supply unit is protected against short-circuit, overload and overvoltage.
1.2.Technical parameters.
Supply voltage 176 ÷ 264 V AC 50÷60Hz
Current consumption 1,36A@230VAC max.
Supply power 200W max.
Efficiency 85%
Output voltage 24V DC
Output current t
AMB
<30°C 7A - see graph 1.
Output current t
AMB
=40°C 5A - see graph 1.
Voltage adjustment range 24 V ÷ 28V DC
Ripple voltage 150mV p-p max.
Short-circuit protection SCP electronic, automatic recovery
Overload protection OLP 105-150% of power supply, automatic recovery
Surge protection varistors
Overvoltage protection OVP >32V (automatic return)
Optical signalisation green LED – presence of DC voltage
Operation conditions 2-nd enviromental class, temperature: -10
o
C÷40
o
C
relative humidity 20%...90%, without condensation
Dimensions (LxWxH) 226 x 115 x 50 [mm]
Net/gross weight 0,82kg / 0,90kg
Protection class PN-EN 60950-1:2007 I (first) – requires a protective conductor (PE)
Connectors power-supply:Φ0,63-2,50 (AWG 22-10)
outputs: Φ0,63-2,50 (AWG 22-10)
Electrical strength of insulation:
- between input (network) circuit and output
circuits of power-supply (I/PO/P)
- between input circuit and PE protection circuit
(I/P-FG)
- between output circuit and PE protection circuit
(O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection
circuit
100 MΩ, 500V/DC
Storage temperature -20ºC...+60ºC
Vibrations and impulse waves during transport according to PN-83/T-42106
* In order to extend the life of the power supply, the load current of 5A is recommended.
*
See graph 1

2
1.3. Output current vs temperature.
Graph 1.
Allowable output current from the power supply
depending on ambient temperature
(instantaneous load).
2. Installation.
2.1. Requirements.
The power supply shall be mounted by the qualified installer having appropriate (required and necessary for a
given country) permissions and qualifications for connecting (operating) low-voltage installations. The unit shall be
mounted in closed rooms, according to the environment class II, of the normal air humidity (RH=90% max. without
condensation) and the temperature within the range from -10°C to +40°C.
The power supply shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill LVD and
EMC requirements the rules for power-supply, encasing and shielding shall be observed according to application.
Due to the power supply design, the PE wire has to be connected to the corresponding connector of the
supply unit. Operation without proper grounding of the power supply is not allowed!
2.2. Installation procedure.
1. Prior to installation of the power supply unit, make sure that power leads have been disconnected from the
230VAC mains.
2. Install the unit in the previously selected place.
3. Connect the 230VAC power leads. Connect the PE cable (yellow-green) to an appropriate terminal on the
power supply unit (marked with ).
The circuit of the shock protection shall be performed with a particular care, i.e. the yellow and green
protection wire of the power cable shall be connected from one side to the terminal marked by the
symbol of in the casing of the power-supply. Operation of the power-supply without the properly
made and fully operational circuit of the shock protection is
UNACCEPTABLE!
It can result in failure of devices and electric shock.
4. Connect load/loads to proper output connectors of the power supply (positive end is marked as +V,
negative end as -V).
5. Upon the completion of tests and trial activation, close the housing, cabinet etc.
2.3. Description of terminal.
Elements/connectors [Fig.1]
Description
L, N, L-N - input voltage connectors 230 V AC,
– protective conductor connector
-V Power supply output (0V)
+V Power supply output (+24V)
LED1 LED signals the presence of voltage at the unit’s
output
Fig.1. Description of terminal.
ADJ Potentiometer - output voltage adjust

3
2.4. Dimensions and fitting of the PS-2002470 power supply.
Fig. 2. Dimensions of power supply.
3. Maintenance.
All maintenance procedures can be performed after the disconnection of the power supply from the electrical grid.
The power supply does not require any special maintenance procedures, but in the case of significant dust accumulation,
dusting using compressed air is recommended.

4
WEEE designation
The waste electric and electronic equipment worn out may not be disposed of together
with standard household waste. According to the WEEE directive, applicable in the EU,
the separate neutralization methods should be used for electric and electronic
equipment.
Pulsar K.Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl
ENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a two-year warranty for the equipment counted from the device’s
production date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer includes manufacturing or material defects unless such
defects have been reported within the warranty period (item 1).
3. The equipment subject to warranty is to be brought to the place where it was purchased or directly to the main office of the
manufacturer.
4. The warranty applies to complete equipment accompanied by a properly filled warranty claim with a description of the defect.
5. Should the claim be accepted the manufacturer is obliged to provide warranty repairs at the earliest convenienve however
not later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in item 5 may be prolonged if there are no technical possibilities to carry out the repairs or if the
equipment has been conditionally accepted due to the breaking warranty terms by the claimant.
7. All the services rendered by force of the warranty arecarried out at the service centre of the manufacturer exclusively.
8. The warranty does not cover the defects of the equipment resulting from:
- reasons beyond the manufacturer's control
- mechanical damage
- improper storage and transport
- use that violates the operation manual or equipment’s intended use
- fortuitous events including lightning discharges power failures fire flood high temperatures and chemical agents
- improper installation and configuration (in defiance with the manual)
9. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no reponsibility for the defects that result from:
- the damaging malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the
recommendations and requirements contained in the manual or the use of the equipment.