Pulsar S108 User manual

1
S108
v1.4
S108 10-port PoE switch for 8 IP cameras
PL
Edition: 7 from 23.01.2023
Supercedes edition: 6 from 18.07.2019 EN**
Features:
Switch 10 ports
8 PoE ports 10/100 Mb/s (data and power supply)
2 ports 10/100 Mb/s (UP LINK)
Long Range mode (up to 250m)
30 W for each PoE port, supports devices complaint
with the IEEE802.3af/at (PoE+) standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
The PSD 520230 V DC/2,3 A/120 W max.
power supply desktop type included
Additional assembly elements
LED indication
warranty –2 years from production date
Example of use.
1. Technical description
1.1. General description.
S108 is a 10-ports PoE switch designed to supply IP cameras operating in IEEE 802.3af/at standard.
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 –8 ports of the switch. The UP LINK
ports is used for connection of another network device via RJ45 connector. The LEDs at the front panel indicate the operation
status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access
point or router.

2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3 Description of components and connectors.
Table 1. (See Fig. 2)
Component No.
(Fig. 2)
Description
[1]
8 x PoE ports (1÷8)
[2]
2 x UP LINK port
[3]
Power Socket of the DC
[4]
Additional assembly elements
[5]
Switch of mode Long Range
Fig. 2. The view of the switch.

3
1.4 Technical parameters
Table 2.
Ports
10 ports 10/100 Mb/s (8 x PoE + 2 x UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802. 3af/at (1÷8 ports), 52 V DC / 30 W at each port *
Long Range mode
Long Range, VLAN
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
1,6 Gb/s
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
Power supply
~100 ÷ 240 V; 50/60 Hz;1,3 A
the PSD 520230 52 V DC/2,3 A/120 W max. power supply desktop type
Operating conditions
temperature -10°C ÷ +40°C,
relative humidity 5% - 90%, no condensation
Dimensions
W=190, H=28, D=105 [+/- 2mm]
Additional equipment
plate to be fixed surface
Gross/Net weight
1,2 / 1,4 [kg]
Protection class
EN 60950-1:2007
II (second)
Storage temperature
-20°C ÷ +60°C
Declarations
CE
*The given value of 30 W per port is the maximum value. The total power consumption should not exceed 96 W.
2. Installation
2.1. Requirements
The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative
humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. Ensure the free flow of air around
the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the
enclosure.
The switch load balance should be done before installation. The given value of 30 W per port is the maximum value
referring to a single output. The total power consumption should not exceed 96 W. The increased demand for power is
particularly evident in the case of cameras with heaters or infrared illuminators - when launching these features, the power
consumption increases rapidly, which may adversely affect the operation of the switch. As the device is designed for a
continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection in the power supply
circuit should be provided. The electrical system shall be made in accordance with applicable standards and regulations.
2.2. Long Range mode
Switch enables operation in two modes: standard and extended range. When the Long Range switch is in
STANDARD position (see Fig. 5), PoE ports operate at 100 Mb/s up to 100 meters. After switching to EXTEND position,
range is increased to 250 meters and speed is reduced to 10 Mb/s. Additionally, VLAN function, which isolates the PoE
ports between each other (communication takes place between the UpLink ports and individual PoE), is activated. In both
modes, the UpLink port speed is 100 Mb / s.
Note: Changing the modes requires a power restart!

4
2.3. Installation procedure
1. Connect switch to the PSD520230 52 V DC power supply unit desktop type.
2. Connect the power supply to the 230 V socket.
3. Connect the camera wires to the RJ45 connectors (connectors PoE).
4. Check the optical indication of switch operation (see Table 3).
Connection schemes

5
3. Operation indication.
Table 3. Operation indication
OPTICAL INDICATION AT THE PoE PORTS (1÷8)
GREEN LED LIGHT (PoE)
Indication of the PoE power
supply at the RJ45 ports
OFF - no power supply at the RJ45 port (the device is not connected or not compliant with
the IEEE802.3af/at standard)
ON –power supply at the RJ45 port
Blinking –short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices 10/100 Mb/s
and data transmission
OFF - no connection
ON - the device is connected 10/100 Mb/s
Blinking –data transmission
OPTICAL INDICATION AT THE UP LINK PORTS
GREEN LED LIGHT
Port on the left side:
No lit - no voltage
Lit –switch operates properly
Port on the right side:
No lit –switch operates in normal mode
Lit–Long Range mode active
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices 10/100 Mb/s
and data transmission
OFF - no data transmission
ON - the device is connected 10/100 Mb/s
Blinking –data transmission
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste. According to the
European Union WEEE Directive, waste electrical and electronic equipment should be disposed of separately from normal
household waste.
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone]
e-mail: [e-mail]
http:// www.pulsar.pl