Pulsar PSB-251215 User manual

1
PSB-251215
PSB 13,8V/1,5A enclosed switch
mode b
uffer power supply
Edition: 2 from 04.02.2013
Supercedes edition: 1 from 08.03.2012 EN
Features of the power supply:
•DC 13,8V/1,5A uninterruptible power supply
•wide AC input voltage range 176÷264V
•high efficiency 70%
•controlling of battery charging and maintaining
•protecting of battery against excessive discharging
(UVP)
•battery charging current 0,5A
•additional accessories: automation module
MPSB12 (technical outputs):
•FAC technical output indicating AC power loss
•FPS technical output indicating PSU failure
•FLB technical output indicating battery low
voltage
•battery output is full protected against short-
circuit and reverse connection
•LED optical signalisation
•protections:
•SCP short-circuit protection
•OVP overvoltage protection
•overvoltage protection
•overload (OLP)
•warranty – 2 year from the production date
1. Technical description.
1.1 General description.
Buffer-type power supply units are intended for continuous power supply to devices that require stabilised voltage
of 12 V DC (+/-15%). The power supply provides a voltage of U=13,8 V DC with an output current of I=1A+ 0,5A battery
charging. In case of power voltage decay, prompt switching to battery supply occurs. The power supply has the following
protections: short-circuit (SCP), overload (OLP) and overvoltage (OVP).
Under normal operation, the total current drawn by the equipment may not exceed I = 1 A; Maximum
battery charging current: 0.5 A. Total device current + battery: 1,5 A max.
1.2.Technical parameters.
Supply voltage 176÷264V AC
Current consumption 0,35A@230VAC max.
Supply power 25W max.
Efficiency 70%
Output voltage 11V÷ 13,8VDC – buffer operation
9,5V÷13,8V DC – battery operation
Output current 1A + 0,5A battery charging
Output current t
AMB
<30°C 1A + 0,5A battery charging - refer to graph 1.
Output current t
AMB
=40°C 0,7 A + 0,5A battery charging - refer to grap h 1.
Voltage adjustment range 12÷14V DC
Ripple voltage 120mV p-p max.
Battery charging current 0,5A max
Short-circuit protection SCP
electronic, automatic recovery
Overload protection OLP 105-150% of power supply, automatic recovery
Overload protection (battery) OLP polymer fuse (PTC)
Surge protection varistors
Overvoltage protection OVP
>16V (automatic recovery)
Excessive discharge protection UVP U<9,5 V (± 5%) – disconnection of battery
Optical signalisation green LED- presence of AC voltage
Output of optical signalization LED AC- presence of AC voltage
LED DC- presence of DC voltage on power supply output
Additional accessories Module MPSB12 (
technical outputs )
Operation conditions 2-nd enviromental class, temperature: -10
o
C÷40
o
C
relative humidity 20%...90%, without condensation

2
Dimensions (LxWxH) 110 x 78 x 36 [mm]
Net/gross weight 0,28kg / 0,31kg
Protection class PN-EN 60950-1:2007 I (first) - requires a protective conductor (PE)
Connectors power-supply: Φ0,63÷2,5 I/O PCB : Φ0,41÷1,63
battery output BAT: 6,3F-2,5/40cm,
output of optical signalization: plug 3-pin 5 mm
Electrical strength of insulation:
- between input (network) circuit and output circuits
of power-supply (I/P-O/P)
- between input circuit and PE protection circuit (I/P-
FG)
- between output circuit and PE protection circuit
(O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection
circuit
100 MΩ, 500V/DC
Storage temperature -20ºC...+60ºC
Vibrations and impulse waves during transport according to PN-83/T-42106
1.3. Output current vs temperature.
Graph 1.
Allowable output current from the power
supply depending on ambient temperature.
2. Installation.
2.1. Requirements.
The buffer power supply shall be mounted by the qualified installer having appropriate (required and necessary
for a given country) permissions and qualifications for connecting (operating) 230V/AC installations and low voltage
installations. The device shall be mounted in closed rooms, according to the environment class II, of the normal air
humidity (RH=90% max. without condensation) and the temperature within the range from -10°C to +40°C.
The power supply shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill LVD and
EMC requirements the rules for power-supply, encasing and shielding shall be observed according to application.
Due to the power supply design, the PE wire has to be connected to the corresponding connector of the
supply unit. Operation without proper grounding of the power supply is not allowed!
Prepare the power supply loading balance before installation. Under normal operation, the total current
drawn by the device may not exceed I = 1 A. Maximum battery charging current: 0,5 A. Total device current +
battery: 1,5 A max.
2.2. Installation procedure.
1. Before beginning installation, ensure that the power in the 230V AC power supply circuit is disconnected.
2. Install the unit in the previously selected place.
3. Connect the 230VAC power leads. Connect the PE cable (yellow-green) to an appropriate terminal on the
power supply unit (marked with ).
The circuit of the shock protection shall be performed with a particular care, i.e. the yellow and green
protection wire of the power cable shall be connected from one side to the terminal marked by the
symbol of in the casing of the power-supply. Operation of the power-supply without the properly
made and fully operational circuit of the shock protection is
UNACCEPTABLE!
It can result in failure of devices and electric shock.

3
4. Connect load/loads to proper output connectors of the power supply (positive end is marked as +V,
negative as -V).
5. Connect battery to the unit according marks (colors).
6. After the completion of tests and trial activation, close the housing, cabinet etc.
2.3. Description of terminals.
Elements/connectors
[Fig.1]
Description
L, N,
L-N - input voltage connectors 230 V AC,
– protective conductor connector
-V
Power supply output (0V)
+V
Power supply output (+13.8V)
LED1
LED signals the presence of AC voltage
ADJ
Potentiometer - output voltage adjust
B+
Battery terminal- positive (+)
Fig 1. Description of terminals. B-
Battery terminal- negative (-)
Z1
Connector of optical signalization
2.4. Dimensions and fitting of the PSB-251215 power supply.
Fig. 2. Dimensions of power supply.

4
3. Cooperation with the MPSB12 automation module (option).
The MPSB12 automation module is intended for indicating the operating status of buffer power supplies, PSB
13,8V type. The PCB board features LEDs that indicate PSU operating status (presence of AC voltage, presence of DC
voltage, battery voltage). The module is also equipped with technical outputs of: FAC - AC power loss,
FPS - PSU failure, FLB -low battery voltage.
Table 1. Elements of the PSU
Element no. Description
[1] LED indicating presence of AC power
[2] LED indicating presence of DC power
[3] LED indicating correct battery voltage
[4] FAC- AC absence technical output – relay type
[5] FAC- AC absence technical output – OC type
[6] FPS- output indicating DC absence/PSU failure - OC type
[7] FLB- output indicating battery low voltage - OC type
[8] Connector of extra LED indication
[9] Additional optical indication
[10] Battery connectors: +BAT =red, - BAT = black
Fig. 3. The view of the PSU with the MPSB12 module.
4. Maintenance.
All maintenance procedures can be performed after the disconnection of the power supply from the electrical grid.
The power supply does not require any special maintenance procedures, but in the case of significant dust accumulation,
dusting using compressed air is recommended.
Pulsar K.Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Polska
Tel. [phone], Fax. [phone]
e-mail: [email protected], [email protected]
http:// www.pulsar.pl, www.zasilacze.pl
WARRANTY
Pulsar K. Bogusz Sp.j. (the manufacturer) grants two -year warranty
for the equipment, counted from the device’s production date.
WEEE MARKING
According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as unsorted municipal waste and to collect such
WEEE separately.