Pulsar SG64-C User manual

1
SG64-C
v1.0
SG64-C 6-ports switch for 4 IP cameras
in the enclosure
PL
Edition: 1 from 04.01.2018
Supercedes the edition: --------- EN**
Features:
Switch 6 ports
4 PoE ports 10/100/100Mb/s (data and power supply)
2 ports 10/100/1000Mb/s (UP LINK)
30W for each PoE port, supports devices complaint
with the IEEE802.3af/at standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
LED indication
Metal enclosure –color white RAL 9003
warranty –2 year from the production date
Example of use.
1. Technical description
1.1. General description.
The SG64-C is a complete kit to build the CCTV system based on IP cameras. The switch and power supply unit are
housed in a metal enclosure.
Automatic detection of any devices powered in the PoE standard is enabled at the 1 –8 ports of the switch. The
UP LINK ports is used for connection of another network device via RJ45 connector. The LEDs at the front panel indicate the
operation status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access
point or router.

2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3 Description of components and connectors.
Table 1. (See Fig. 2)
Component No.
(Fig. 2)
Description
[1]
Switch
[2]
Switch mode buffer power supply unit (PS-604812), 48VDC/1,2A/60W
[3]
Potentiometer adjusting the output voltage of the power supply (48÷53V)
[4]
LED light –power supply operation indication
[5]
T 6,3A / 250V fuse socket
[6]
Holders for mounting cable
Fig. 2. The enclosure view.

3
Table 2. (See Fig. 3)
Component No
(Fig. 3)
Description
[1]
2 x UP LINK port
[2]
4 x PoE ports (1÷4)
[3]
48VDC power supply socket
Fig. 3. The view of the switch.
1.4 Technical parameters (tab.3)
Table 3.
Ports
6 ports 10/100/1000Mb/s (4 x PoE + 2 x UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af/at (1÷4 ports), 48V DC / 30W at each port *
Used pairs 4/5 (+), 7/8 (-)
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
8,8Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
Mains supply
176 ÷264VAC 50Hz/ 0,6A/230VAC
Operating conditions
temperature -10°C ÷ 40°C,
relative humidity 5% - 90%, no condensation
Dimensions
W=275, H=281, D+D1=102+14 [+/- 2mm]
W1=280, H1=285 [+/- 2mm]
Enclosure
Steel plate, DC01 1,0mm color white RAL 9003
Closing
Cheese head screw x 1 (at the front)
Notes
The enclosure does not touch the assembly surface so that cables can be led.
Gross/Net weight
2,6/2,8 kg
Protection class
EN 60950-1:2007
II (druga)
Storage temperature
-20°C ÷ 60°C
Declarations, warranty
CE, 2 year from the production date
*The given value of 30W per port is the maximum value. The total power consumption should not exceed 48W when all PoE ports are being used.

4
2. Installation
2.1. Requirements
1. The device should be mounted by a qualified installer, holding relevant permits and licenses (applicable and required
for a given country) for 230V/AC and low-voltage installations.
2. The device shall be mounted in confined spaces, according to the environment class II, with normal air humidity
(RH=90% max. without condensation) and the temperature from -10°C to +40°C.
3. The switch shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of
the enclosure. Before installation, prepare a Switch'a load balance. The given value of 30W per port is the maximum
value referring to a single output. The total power consumption should not exceed 48W when all PoE ports are
being used. The increased demand for power is particularly evident in the case of cameras with heaters or infrared
illuminators - when launching these features, the power consumption increases rapidly, which may adversely affect the
operation of the switch. As the device is designed for a continuous operation and is not equipped with a power-switch,
therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be
informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical
system shall follow valid standards and regulations.
2.2. Installation procedure
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (~230Vac) to L-N clips of the PSU.
The shock protection circuit shall be performed with a particular care, i.e. the yellow
and green wire coat of the power cable shall stick to one side of the terminal - marked
with ‘ ‘symbol on the PSU enclosure. Operation of the PSU without the properly
made and fully operational shock protection circuit is UNACCEPTABLE! It can cause a
device failure or an electric shock.
4. Connect the ground wire to the terminal marked with the symbol (power supply module connector). Use a three-
core cable (with a yellow and green PE protection wire) to make the connection. Lead the cables to the appropriate clips
through the insulating bushing of the connection board.
5. Connect the power (~230V).
6. Connect the camera cables to the RJ45 connectors (PoE connectors)
7. Check the optical indication of the switch operation.
8. After installing and checking proper working, the enclosure can be closed.
Connection schemes

5
3. Operation indication.
Table 4. Operation indication
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
GREEN LED LIGHT (Power)
Indication of the switch's
power supply
OFF –no power supply of the switch
ON –power supply on, normal operation
OPTICAL INDICATION AT THE PoE PORTS (1÷4)
GREEN LED LIGHT (PoE)
Indication of the PoE power
supply at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant
with the IEEE802.3af/at standard)
ON –supply at the RJ45 port
Blinking –short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10/100/1000Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10/100/1000Mb/s
Blinking –data transmission
OPTICAL INDICATION AT THE UP LINK PORTS
GREEN LED LIGHT
OFF- no connection or device connected 10/100Mb/s
ON –the device is connected 1000Mb/s
YELLOW LED LIGHT (LINK)
The connection status of
LAN devices,
10/100/1000Mb/s
and data transmission
OFF- no data transmission
ON - the device is connected 10/100/1000Mb/s
Blinking –data transmission

6
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment
should be disposed of separately from normal household waste .
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], sal[email protected]
http:// www.pulsar.pl, www.zasilacze.pl