PURE Evoke H2 User manual

Evoke H2

ES
EN
ES
NL
IT
DA/NO
FR
DE
1
Thank you for choosing Evoke H2. This manual will help you get your product
up and running in no time and explains how to get the best out of all its great
features. If you need any further assistance, please visit the support pages on
our website at support.pure.com.
Evoke H2

2
Symbols on the product and in the user manual
Potentially serious risk to your personal safety. To avoid possible injury or death, obey all safety notices with this symbol.
Caution. Read the user manual before use.
Pantone
Cool Grey 7C
Name Windsor Trim Button Artwork
Part # 15A90
Version 4
Date 02/07/2015
Where to switch on or off the product, or put it in standby.
Part
Project
Sub Assembly
Doc Type
Customer
Version
Version Date
106KL
Chalk
Rear
Label Artwork
Pure
7
23/05/2017
History V1-6 - Legacy
V7 - Address ammended, DC symbol changes.
Alert symbol removed.
5.5V DC power supply input, 1 amps.
Part
Project
Sub Assembly
Doc Type
Customer
Version
Version Date
106KL
Chalk
Rear
Label Artwork
Pure
7
23/05/2017
History V1-6 - Legacy
V7 - Address ammended, DC symbol changes.
Alert symbol removed.
DC conenctor polarity, the centre of the connector terminal is positive.
ChargePAK B1 safety instructions
1. Read the instructions for ChargePAK use in this document.
2. Only use your ChargePAK with original Pure products. Use only the original Pure ChargePAK B1.
3. Store ChargePAK in a cool, dry place at normal room temperature. Remove from devices that will be stored unused for extended periods.
4. Do not puncture, modify, drop, throw, or cause other unnecessary shocks to your ChargePAK. May present a risk of fire, explosion, or chemical burn if
mistreated.
5. Do not dispose of ChargePAK in a fire or incinerator, or leave in hot places such as a motor car under direct sunlight. Do not store near oven, stove, or
other heat source.
6. Do not connect ChargePAK directly to an electrical source, such as a building outlet or automobile power-point. Do not place into a microwave oven, or
any other high-pressure container.
7. Do not immerse ChargePAK in water or otherwise expose it to liquids.
8. Do not short circuit ChargePAK.
9. Do not use or charge a ChargePAK that appears to be leaking, discoloured, rusty, deformed; emitting an odour; or is otherwise abnormal.
10. Do not touch a leaking ChargePAK directly; wear protective material to remove and dispose of it properly immediately.
11. Do not store where children may have access.
12. Dispose of ChargePAK as per normal rechargeable batteries according to the local laws and regulations of your region. Some batteries may be
Safety information
1. Familiarise yourself with all of the safety information and instructions before using the radio. When passing this radio on to others, please include all
documents.
2. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
If liquid or water is spilled on to the radio, switch it off at the mains immediately, disconnect the mains plug and contact your dealer.
Never touch the plug or the radio itself with wet hands. Never pull the power cable when disconnecting the power adaptor from the power supply.
3. The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like
4. Using the radio in rooms or climates with high humidity and temperatures may cause condensation to form inside the radio, which can damage the
radio. Use apparatus in moderate climates only.
5. Avoid extreme degrees of temperature,either hot or cold. Place the device well away from heat sources such as radiators or gas/electric fires. No naked
flame sources, such as lighted candles, should be placed on the apparatus
6. The mains power adapter is used as the disconnect device, the disconnect device shall remain readily operable.
Fit the mains adaptor to an easily accessible socket located near the radio and ONLY use the mains power adapter supplied.
7. Use only power supplies listed in the user instructions. (Models KSAA0550100W1UV-1 / SW0551000-A01 or SW0551000-AM).
8. Ensure that the available supply voltage corresponds with the required operational voltage of the radio before use.
9. Disconnect your radio from the power supply if you will not use your radio for a long period of time (e.g. if you are going on holiday).
10. Always unplug your radio from the mains socket before cleaning. When cleaning the radio, do not use any type of abrasive pad or abrasive cleaning
solutions as these may damage the radio’s surface.
11. To reduce the risk of electric shock, do not remove any screws as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

3
EN
Contents
4 Introduction
4 Front panel controls
4 Display
5 Rear panel
6 Getting started
6 Quick set up
7 Using your Evoke
7 Selecting digital radio
7 Selecting FM radio
7 Pausing and controlling scrolling text
8 Storing and selecting presets
8 To quick-store a station to a preset button
(1-3)
8 To store a station to the preset list (1-10)
8 To recall a preset when listening to digital
radio or FM radio
9 Setting the alarm and sleep timer
9 Setting the alarm
9 Cancelling a sounding alarm
9 Snoozing a sounding alarm
9 Disabling an alarm
10 Setting the sleep timer
10 Options and settings
10 General settings
11 Digital radio settings
11 FM settings
11 Audio settings
11 Display settings
12 Clock settings
13 Appendix
13 Installing the ChargePAK B1
14 Technical specifications

4
PURE LCD
PURE LCD
Front panel controls
Introduction
1. Standby:On/standby switch (mains powered) or on/
off switch (ChargePAK powered).
2. Source: Press to switch between Digital radio, FM
radio and Auxiliary input.
3. Menu:Press to access setup options.
4. Volume: Turn to adjust volume. Push to mute and
un-mute.
5. Select:Turn and press to browse and select radio
stations (see page 7), select and adjust menu
options or pause and control scrolling text (see
page 7).
6. Display: See below for more information on the
display options.
7. Presets 1 - 4+: Store up to 10 digital or 10 FM radio
preset stations.
Display
1. Current time.
2. ChargePAK indicator.
3. Source indicator.
4. Displays station name.
5. Signal strength.
6. Volume/mute indicator.
7. Displays date, scrolling text, settings and station
information (see page 12).
8. AM/PM indicator.
9. Alarm set indicator (see page 9).
10. Sleep and kitchen timer indicator (see page 10).
11. Alarm snooze indicator (see page 9).
BBC R1
NEWSBEAT

5
EN
Rear panel
1. 5.5V DC input connection for supplied mains
adapter.
2. 3.5mm stereo headphone socket.
3. 3.5mm auxiliary input connection for an iPod,
MP3 player, etc.
4. Mini-B type USB connector for USB software
updates.
5. Compartment for ChargePAK B1 rechargeable
battery (sold separately).
6. Telescopic antenna.

6
Getting started
Note: If you have a ChargePAK B1 rechargeable battery (sold separately) fit it now before plugging Evoke in.
See page 13 for more information.
1
Quick set up
• Unclip the aerial and fully extend it (steps A and B).
• Insert the jack of the supplied mains adapter into the socket on the rear of the radio (C).
• Plug the mains adapter into the mains supply (D) and press the Standby ( ) button.
5.5V DC
5.5VDC Auxin
ImaginationHouse,HomePark Estate, Kings Langley, Hertfordshire, WD4 8LZ
www.pure.com
H2
Designedand engineered in the UK
Assembledin China
D
C
A
B
Select Select
2Select your language when prompted. Turn the Select dial to select a language (ENGLISH/FRENCH/
GERMAN/ITALIAN/SPANISH) and push to confirm.
Wait for the radio to complete an Autotune for all available stations. When the Autotune is complete, a
station will be selected.
3
LANGUAGE
ENGLISH
LANGUAGE
ENGLISH
SCAN 15
******
1min
BBC R1
TUNING
BBC R1
NEWSBEAT

7
EN
Using your Evoke
Selecting digital radio
Press Source to switch to digital radio.
Changing digital stations
1. Turn the Select dial to the station you want to listen to.
2. Push the Select dial to tune into the station.
Selecting FM radio
Press Source to switch to FM radio.
Seek tuning
Turn and release the Select dial right or left to seek to the next or
previous FM radio station that has a strong signal.
Manual tuning
1. Change the FM radio tuning mode to ‘ MANUAL ’ (see page 11).
2. Turn the Select dial right or left to step up or down 0.05 MHz.
Using the auxiliary input
1. Connect the line out or headphone socket of your auxiliary device to
the Aux In socket on your Evoke using a suitable cable.
2. Press Source to switch to auxiliary input.
3. The Auxiliary input screen will display and Evoke will play any audio
that is playing on the auxiliary device.
Pausing and controlling scrolling text
1. When ‘Scrolling text’ information is displayed in either digital or FM
radio, push the Select dial to pause the scrolling text.
2. Turn the Select dial to scroll forwards and backwards through the
text. To exit push the Select dial again.
DR
FM
AUX
BBC R1
NEWSBEAT
STATIONS
BBC R6
88\65
16-6-15
SCANNING
88\65
BBC R2
PICK OF
16-6-15
AUX

8
To quick-store a station to a preset button (1-3)
Tune to the digital or FM radio station you want to store. Press and hold one of the
numbered preset buttons (1to 3) for two seconds to save the current station as a
preset. You can save over existing presets.
To store a station to the preset list (1-10)
1. Tune to the digital radio or FM radio station you want to store.
2. Press and release the 4+ button to view the numerical list of stored presets, then
turn the Select dial to choose any preset number between 1 and 10. You can
overwrite existing presets.
3. Press and hold the Select dial until you see the ‘PRESET STORED’ message.
To recall a preset when listening to digital radio or
FM radio
To tune to presets 1 to 3, press the corresponding numbered button on Evoke (1to 3).
To access the full list of presets (from 1 to 10):
1. Press and release the 4+ button.
2. Turn the
Select dial right or left to scroll through the list of presets and push the
Select dial to tune to the selected preset.
Store up to 10 digital and 10 FM radio stations for quick access.
Storing and selecting presets
BBC R1
NEWSBEAT
PRESET 2
STORED
PRESET
EMPTY
RECALL
2 BBC R1
BBC R1
NEWSBEAT

9
EN
Setting the alarm and sleep timer
The alarm in Evoke switches the radio on (if in standby) and tunes to a digital or FM radio station or sounds a tone.
Note: The alarm function does not work when Evoke is being powered by the ChargePAK B1.
Setting the alarm
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘ALARM’.
3. Turn and press the Select dial to choose ‘ON’.
4. Turn and press the Select dial to set the hour for the alarm. Repeat to set the
minutes for the alarm.
5. Turn and press the Select dial to specify one of the following alarm repeat
options: ‘ONCE’, ‘DAILY’, ‘WEEKDAYS’, ‘WEEKENDS’, ‘SATURDAY’ or ‘SUNDAY’
and press the Select dial to confirm.
6. Turn and press the Select dial to specify ‘FM’, ‘DAB’ or ‘TONE’. If you are
specifying a tone alarm, skip to step 9.
7. Turn and press the Select dial to specify which station should be played when the
alarm goes off. You have the option of selecting one of your preset stations or you
can select ‘LAST USED’ to select the station that you were last listening to.
8. Turn and press the Select dial to set the volume that the radio will play at when
the alarm sounds.
9. The alarm icon will appear on the display to show that the alarm is set.
Cancelling a sounding alarm
To cancel a sounding tone alarm, press either the Menu or Source button, or push the
Select dial.
Note: If you have set up your alarm to tune into a radio station, you can only cancel the
alarm by pressing the
Standby () button.
the latest news
BBC Radio 2
PM
DR
ALARM
ON
DAB
ALARM
ON TIME
7-00 AM
REPEAT
DAILY
SOURCE
TONE
ALARM
SAVED
BBC R1
NEWSBEAT
Snoozing a sounding alarm
To snooze a sounding alarm, press either the 1, 2, 3or 4+ preset number buttons .
Disabling an alarm
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘ALARM’.
3. Turn and press the Select dial to choose ‘OFF’.
4. The alarm icon on the display will disappear.

10
Setting the sleep timer
The sleep timer can be set to switch Evoke off after a period of time.
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘SLEEP’.
3. Turn and press the Select dial to set the timer for up to 90 minutes or choose
‘OFF’ to cancel.
4. The sleep timer icon will appear on the display to show that the sleep timer is set.
the latest news
BBC Radio 2
PM
DR
SLEEP
30 MINS
BBC R1
NEWSBEAT
Options and settings
General settings
Changing the language
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘SETTINGS’.
3. Turn and press the Select dial to choose ‘LANGUAGE’.
4. Turn and press the Select dial to select a menu language from ‘ENGLISH’, ‘FRENCH’, ‘GERMAN’, ‘ITALIAN’ or ’SPANISH’.
Factory reset
Resetting your Evoke removes all presets, stored stations, alarms and resets all other options to default settings.
1. Press the Menu button.
2. Turn and press the Select dial to ‘SETTINGS’.
3. Turn and press the Select dial to ‘RESET’.
4. Turn and press the Select dial to confirm that you want to reset the Evoke to default settings.
Version
To display the software version:
1. Press the Menu button.
2. Turn and press the Select dial to ‘SETTINGS’.
3. Turn and press the Select dial to ‘VERSION’.
Update
Contact Pure technical support (http://support.pure.com) for more information on how to update Evoke to the latest
software version.

11
EN
Digital radio settings
Autotune
You can use the autotune function to automatically scan for new digital radio stations and remove inactive ones.
Note: Autotune is only available when you have selected ‘Digital’ as the radio source.
To carry out an autotune:
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘AUTOTUNE’. The number of stations found will be displayed during the autotune.
When the autotune has finished, Evoke will tune to the last station that you were listening to.
FM settings
FM stereo option
You can choose between ‘STEREO’ or ‘MONO’ reception when listening to FM radio. You may want to choose ‘STEREO‘ if
listening using headphones.
Note: The FM stereo option is only available when you have selected ‘FM’ as the radio source.
To change between stereo or mono reception:
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘FM STEREO’.
3. Turn and press the Select dial to choose between ‘STEREO’ or ‘MONO’ FM reception.
FM tuning mode
Press the Menu button and turn and press the Select dial to choose ‘TUNE’. Choose from the following two modes:
SEEK: When you turn the Select dial, the radio tunes to the next station with a good signal.
MANUAL:When you turn the Select dial, the radio tunes up or down the FM radio frequency range by 0.05 MHz.
Audio settings
To adjust the bass and treble settings:
1. Press the Menu button.
2. Turn and press the Select dial to choose ‘AUDIO’.
3.
Turn and press the Select dial to choose ‘ BASS ’ or ‘ TREBLE ’.
4. Turn and press the Select dial to set the level from ‘-6’ (low) to ‘+6’ (high).
Display settings
Changing the backlight brightness level
1. Press the Menu button and turn and press the Select dial to choose ‘ DISPLAY ’.
2. Turn and press the
Select dial to choose ‘ BACKLIGHT ’.
3. Turn and press the
Select dial to adjust the brightness level when Evoke’s display is ‘ ACTIVE’ or in ‘ STANDBY ’.
4. Turn and press the
Select dial to select ‘ LEVEL ’.
5. Turn and press the
Select dial to set a brightness level between ‘ 1 ’ (dim) and ‘ 5 ’ (bright).

12
Changing the duration that the backlight is illuminated
1. Press the Menu button and turn and press the Select dial to choose ‘ DISPLAY ’.
2. Turn and press the
Select dial to choose ‘ BACKLIGHT ’.
3. Turn and press the
Select dial to adjust the duration the backlight is illuminated for when Evoke’s display is ‘ ACTIVE ‘ or in
‘ STANDBY ’.
4. Turn and press the
Select dial to select ‘ DURATION ’.
5. Turn and press the
Select dial to choose one of the following option s:
ON: The backlight will always be illuminated at your preferred brightness level.
TIMED: The backlight will always be illuminated at your preferred brightness level when a button is pressed and then
switch off after 7 seconds of inactivity.
Changing the information shown on the display
1. Press the Menu button and turn and press the Select dial to choose ‘DISPLAY’.
2. Press Menu and turn and press the Select dial to choose ‘INFORMATION’.
3. Turn and press the Select dial to choose one of the following options:
TEXT: Provided by the broadcaster.
STRENGTH: The clear block indicates signal strength for reliable reception.
DATE: Displays the current date.
QUALITY: (Digital radio only) Signal quality, from ‘0’ (low) to ‘100’ (high).
Changing the time format
1. Press the Menu button and turn and press the Select dial to choose ‘CLOCK’.
2. Turn and press the Select dial to choose ‘12/24 HOUR’. Repeat to set the required time format.
Changing the date format
1. Press the Menu button and turn and press the Select dial to choose ‘CLOCK’.
2. Turn and press the Select dial to choose ‘FORMAT’. Repeat to set the required date format.
Clock settings
Setting the time and date
The time and date on Evoke are automatically set by the FM or digital radio signal. If the time/date does not update automatically,
you can manually set it using this option.
Note: Any time or date updates received by an FM or a digital broadcast will override manual settings, if clock synchronization is
enabled (see the following page for more information).
Setting the time and date manually
1. Press the Menu button and turn and press the Select dial to choose ‘CLOCK’.
2. Turn and press the Select dial to choose ‘TIME/DATE’.
3. Turn and press the Select dial to set the hour. Repeat to adjust the minutes.
4. Turn and press the Select dial to set the day of the month. Repeat to set the month and year.