Pxmalion Core I3 User manual

Pxmalion 3D Printer Core I3
Assembly Instructions

Thank you for purchasing from Pxmalion.
GETTING STARTED
Before you set up your Pxmalion 3D printer Core I3, remember that:
1. Please check all the components according to the packing lists following. Send us an email to
[e-mail] if you have any issue on it.
2. Several parts (e.g. X- Y- Z- motors, X- Y- sliders, nozzle) had been preassembled at the Pxmalion factory.
Please check whether the screws and nuts on them were loosed during transportation and tighten them.
3. For more detailed steps, you may check the assembly instruction video by clicking in the following link:
www.pxmalion.com.

1. Components
400mm Mounts
2PCS
340mm Mounts
2PCS
T Connectors
4PCS
Connecting plates 2PCS
First Layer Connecting plate Y 1PCS 8MM Guiding pins
(420mm in length) 2PCS
8MM Guiding pins
(343mm in length)
2PCS
10mm Guiding pin
(320mm in length) 2PCS
Screw rods 2PCS Acrylic plate A 1PCS Acrylic plate B 1PCS Acrylic plate C 1PCS Acrylic plate D 1PCS

Second Layer
Filament Holder
1PCS
Filament Holder
1PCS
Heat Bed & Glass
(Glass is below
the heat bed)

X-
axis motor & support
1PCS
X- idler holder
1PCS
Y-
axis motor & support
1PCS
X-slider & nozzle
1PCS
Y-slider
1PCS
Z-guiding pin support
1PCS
Z-axis motor
1PCS
Adapter
1PCS
Third
Layer
Mechanic parts 1PCS Electronic parts 1PCS Assembly tools 1PCS
Screws-X 1PCS Screws-Y 1PCS Screws-Z 1PCS
Control box 1PCS

1.1 Mechanic parts list
Parts Q’ty
Springs 4 PCS
Clips 4 PCS
Foot pads 4 PCS
Pulley 5mm 2 PCS
Pulley 8mm 2 PCS
Screw rod washer 1 PCS
Flange Bearing 3 PCS
Closed-
ended timing
belt 1 PCS
Open-ended timing
belt (the longer one) 1 PCS
Open-ended timing
belt (the shorter one)
1 PCS
Coupler 1 PCS
Z-axis holder 2 PCS
Z- Belt adjustment
piece 1 PCS

1.2 Electronic parts list
Parts Q’ty
Extruder cable, 1500mm
1 PCS
X motion motor cable,
800mm 1 PCS
Y motion motor cable,
650mm 1 PCS
Z motion motor cable,
500mm 1 PCS
X limit switch cable 1 PCS
Y limit switch cable 1 PCS
Z limit switch cable 1 PCS
Extruder cooling fan
cable, 1200mm 1 PCS
Auto leveling cable,
1000mm 1 PCS
Cable ties 20 PCS
Auto Bed Leveling 1 PCS
Micro SD card 1 PCS
Card Reader 1 PCS
Cable Sleeve 1 PCS

1.3 Assembly tools list
Tool Q’ty
1.5mm Allen wrench 1 PCS
2mm Allen wrench 1 PCS
2.5mm Allen wrench 1 PCS
3MM Allen wrench 1 PCS
5.5-7mm open end wrench 1 PCS
Belt clipper 1 PCS
Straight screwdriver 1 PCS

1.4 Screws list Name specification Q’ty
Countersink
head hex socket
screw
Screw-X
Cup head hex socket screw M2*8 2 PCS
Cup head hex socket screw M3*5 2 PCS
Cup head hex socket screw M3*10 2 PCS
Button head hex socket screw M4*25 2 PCS
Button head hex
socket screw
Lock nut M4 4 PCS
Cup head hex socket screw M2*8 2 PCS
Screw-Y
Cup head hex socket screw M2*16 2 PCS
Cup head hex socket screw M3*16 2 PCS
Cup head hex
socket screw
Button head hex socket screw M4*8 8 PCS
Button head hex socket screw M4*10 4 PCS
Button head hex socket screw M4*25 4 PCS
Lock nut M2 2 PCS
Lock nut M3 2 PCS
Lock nut M4 4 PCS
T nut M4 12 PCS
T nut
Cup head hex socket screw M2*16 2 PCS
Cup head hex socket screw M3*16 2 PCS
Screw-Z
Cup head hex socket screw M2*8 2 PCS
Cup head hex socket screw M3*12 2 PCS
Button head hex socket screw M4*6 6 PCS
Lock nut
Button head hex socket screw M4*8 16 PCS
Countersink head hex socket screw M4*8 8 PCS
Button head hex socket screw M4*16 4 PCS
Button head hex socket screw M4*25 4 PCS
Countersink head hex socket screw M4*25 4 PCS
Meter screws M4 4 PCS
Set screw
Lock nut M3 2 PCS
Lock nut M4 8 PCS
T nut M4 18 PCS
Cup head hex socket screw M2*8 2 PCS
Cup head hex socket screw M3*12 2 PCS

X-Axis Assembly
ATTENTIONS:
1. Pay attention to the installation orientation of the X motion motor.
2. The open-ended belt (the longer one) will be used here.
3. The bearing on X motion slider is loose. So please tighten the screws after the guiding pin and
timing belt are installed properly.
4. The nozzle had been preassembled at the Pxmalion factory. Please check it was loosed during
transportation and tighten them.