Quadra-Fire 5100I User manual

5100-I WOOD INSERT
1445 North Highway
Colville, WA 99114
SAVE THESE INSTRUCTIONS
www.quadrare.com
Part 250-1960 Rev B January 30, 2004
O-T L
Tested and
Listed by
Beaverton
Oregon USA
OMNI-Test Laboratories, Inc.
C
R
PRIOR TO FIRST FIRE: Remove all labels from glass. Clean plated surfaces with a glass cleanser and soft cloth
to prevent staining from ngerprint oils.
This manual contains instructions for Installation, Operation & Maintenance. Please read this entire
manual before you install and use your new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
IMPORTANT SAFETY NOTES:
1) When installing your insert, particular attention should be paid to re protection. If this room heater is not properly
installed, a house re may result. To reduce the risk of re, follow the installation instructions. Contact local building, re
ofcials or authority having jurisdiction about restrictions,installation inspection and permits requirements in your area.
2) CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar liquids to start or
“freshen up” a re in this heater. Keep all such liquids well away from the heater while it is in use.
3) During operation, if any part of the insert starts to glow, the insert is in an overred condition. Close the air controls
completely by pulling them out, until the glowing has stopped. OVERFIRING VOIDS YOUR WARRANTY!
4) Cool ashes should be disposed of carefully, using a metal container.
5) Do not burn wet or green wood. Store wood in a dry location.
6) DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not
burn treated wood, or wood with salt (driftwood, etc.). Burning materials other than wood (including charcoal) under
adverse conditions may generate carbon monoxide in the home, resulting in illness or possible death.
7) Do not permit creosote or soot to accumulate excessively in the chimney or inside the rebox.
8) Check your chimney system thoroughly when installing into an existing metal or masonry chimney. Seek professional
advice if in doubt about its condition.
9) Do not connect this unit to a chimnney ue already serving another appliance.
10) Comply with all minimum clearances to combustibles as shown in this manual for this appliance.
11) Build re on brick rebox oor. Do not use grates, andirons or other methods to support fuel.
12) HOT WHILE IN OPERATION! Keep children, pets, clothing and furniture away. Contact can cause skin burns.
13) Do not connect to any air distribution duct or system.
14) RISK OF FIRE! Do not operate with insert door open. Operating with door open could result in overring.
15) For further information refer to NFPA 211 (US) or CAN/CSA-B365 (Canada).
16) Do not operate without fully assembling all components.
17) Do not operate with broken glass.

5100-I WOOD INSERT
Page 2 January 30, 2004
R
250-1960 Rev B
Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and performance.
This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make
products that will satisfy your needs. Our Research and Development facility then employs the world’s most advanced
technology to achieve the optimum operation of our stoves, inserts and replaces. And yet we are old-fashioned when it
comes to craftsmanship. Each unit is meticulously fabricated and gold surfaces are hand-nished for lasting beauty and
enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspection. Additionally, we feel
it is important to offer you several nishing options and accessories to complement your home’s décor, individualize the
use of your appliance, and provide nancial options in acquiring a quality hearth appliance. Ask your Quadra-Fire Dealer
for information on these options. From design, to fabrication, to shipping: Our guarantee of quality is more than a word,
it’s Quadra-Fire tradition, and we proudly back this tradition with a Limited Lifetime Warranty.
Prior to installation, we ask you to take a few moments to read this manual. It has been our experience that your
overall enjoyment of your new appliance will be greatly enhanced by becoming familiar with its installation, operation
and maintenance. We wish you and your family many years of enjoyment in the warmth and comfort of your hearth
appliance. Thank you for choosing Quadra-Fire.
With warm regards,
___________________________
Alan Trusler
Senior Vice President
Dealer Channel
___________________________
Dan Henry
Vice President
Research & Development
___________________________
Mike Derosier
Vice President
Quadra-Fire Brand Manager
_________________________
Jason Olmstead
Vice President &
General Manager
_________________________
Dave Fiebelkorn
Materials Manager

Page 3
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
SAFETY & OVERVIEW OF APPLIANCE
Dimensions----------------------------------------------------- 4
Minimum Clearances to Combustibles ------------------ 5
Location of Serial Number Label-------------------------- 5
Listings ---------------------------------------------------------- 6
Chimney Height & Draft and 2-10-30 Rule ------------- 6
Installation Recommendations ---------------------------- 5
General Installation Procedures -------------------------- 7
Alternate Floor Protection Worksheet ------------------- 7
Chimney Requirements ------------------------------------- 8
Ovalizing Round Stainless Steel Liners----------------- 8
INSTALLATION OPTIONS
Mobile Home--------------------------------------------------- 9
Masonry Fireplace-------------------------------------------- 10
Metal Heat Circulating Masonry--------------------------- 10
Zero Clearance Factory Built Fireplace ----------------- 11
Canadian Masonry & Heat Circulating ------------------ 12
Leveling Bolts ------------------------------------------------- 12
Securing Liner to Chimney Ring -------------------------- 12
PARTS & ACCESSORY INSTALLATION
Outside Air Installation -------------------------------------- 13
Blower Cord Installation & Snap Disc Operation------ 13
Blower Replacement ----------------------------------------- 14
Fan Speed Control Adjustment---------------------------- 14
Fan Wiring Diagram ------------------------------------------ 14
Panel Sets and Trim Sets ----------------------------------- 15
Zero Clearance Adjustable Trim Support--------------- 16
OPERATION OVERVIEW
Wood Selection & Storing ---------------------------------- 17
Overring ------------------------------------------------------- 17
Building A Fire------------------------------------------------- 17
Burn Rates & Opacity --------------------------------------- 18
Fan Operation Instructions --------------------------------- 18
Ash Removal -------------------------------------------------- 18
Air Quality ------------------------------------------------------ 19
Air Controls, Primary & Start-up-------------------------- 19
MAINTENANCE
Plated Surfaces ----------------------------------------------- 20
Glass Cleaning & Replacement -------------------------- 20
Creosote Formation & Removal -------------------------- 20
Chimney -------------------------------------------------------- 20
Brick Replacement ------------------------------------------- 21
Bafe Removal & Replacement--------------------------- 21
PARTS & ACCESSORIES LIST ------------------------- 22
WARRANTY POLICY--------------------------------------- 23
MODEL NAME Quadra-Fire
5100-I WOOD INSERT
Serial Number
Date Purchased
Dealership Where Purchased
Dealer Phone
Additional Information:
AFTER COMPLETING YOUR WARRANTY CARD, ATTACH
YOUR SALES RECEIPT AND WARRANTY STUB HERE
FOR FUTURE REFERENCE.

5100-I WOOD INSERT
Page 4 January 30, 2004
R
250-1960 Rev B
DIMENSIONS
TOP VIEW
SIDE VIEW
FRONT VIEW
STD 47” 30-1/2”
Large 51-1/4” 34-1/4”
Panel
Size AB
A
B
39-1/8"
(994mm)
26-3/4"
(679mm) 9-1/8"
(232mm)
22-1/4"
(565mm) 21-1/8"
(537mm)
29-5/8"
(752mm)
10-1/2"
(267mm)
34-3/16"
(919mm)
C
L
25-5/8"
(651mm)
12-7/8"
(327mm)
17-7/8"
(454mm)
39-1/8"
(994mm)
12.0"
(305mm)

Page 5
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
SERIAL NUMBER LABEL LOCATION:
ON RIGHT SIDE OF INSERT AS YOU FACE THE APPLIANCE
In Canada a full length 6” (152mm) S635 ue liner required
as per ULC S628.
NOTE: When installling into a masonry replace, the re-
place must be built to UBC Chapter 37 standards. Do not
remove brick or mortar from masonry replace to accomo-
date insert. The permanent metal warning plate provided
must be attached to the back of the replace stating the re-
place may have been altered to accomodate the insert and
must be returned to original condition for use as a conven-
tional replace.
CLEARANCES TO COMBUSTIBLES
United States and Canada
Hearth Extension
A
B
C
D
FE
Insert
SideWall
Fascia or Trim
Mantel
A B C D E F
INSTALLATION: Masonry, Heat Circulating and *Zero Clearance
12" (305) 40" (1016) 35" (889) 7" (178) 16" (406) 8"(200)
18" (457) Canada
With 5" Mantel Deflector, Part No. 831-1520
12" (305) 29" (737) 20" (889) 7" (178) 16" (406) 8"(200)
18" (457) Canada
With 8" Mantel Deflector, Part No. 831-1530
12" (305) 23" (585) 16" (406) 7" (178) 16" (406) 8"(200)
18" (457) Canada
*Zero Clearance in USA Only.
THERMAL PROTECTION USA & CANADA
Thermal protection must be 1 inch (25mm) minimum thickness (“k” value = 0.84) or equivalent material.
See Alternate Floor Protection Work Sheet on page 7.

5100-I WOOD INSERT
Page 6 January 30, 2004
R
250-1960 Rev B
AVOID FIRE: To ensure that insulation or any other combustible
material does not contact the chimney, a chimney inside the house
must have at least 2 inches (51mm) of air space clearance around
t he chimney. A chimney outside the house must have at least 1
inch (25mm) clearance to the combustible structure. Noncombus-
tible re stops must be installed at the spaces where the chimney
passes through oors and/or ceilings. Refer to Figures 8A & 8B
on page 8. Canadian installations require a full reline of the
chimney
CHIMNEY HEIGHT/DRAFT
To be sure that your Quadra-Fire insert burns properly, the chimney
draft (static pressure) should be approximately -0.10” water column
(W.C.) during a high burn and -0.04” W.C. during a low burn,
measured 6” (152mm) above the top of the insert after one hour of
operation at each burn setting.
NOTE: These are guidelines only, and may vary somewhat for
individual installations.
Your Quadra-Fire insert was designed for and tested on a 6”
(152mm) chimney, 12 ft-14 ft (360-420cm) high, measured from
the base of the insert. The further your stack height or diameter
varies from this configuration, the possibility of performance
problems increases. In addition, exterior conditions such as roof
line, surrounding trees, prevailing winds and nearby hills can
inuence insert’s performance.
A masonry chimney or a listed factory-built UL103 HT Class “A”
chimney must be the required height above the roof and any other
nearby obstructions. The chimney must be at least 3 ft (91cm)
higher than the highest point where it passes through the roof and at
least 2 ft (61cm) higher than the highest part of the roof or structure
that is within 10 ft (305cm) of the chimney, measured horizontally.
See 2-10-3 Rule (Figure 6A). These are safety requirements
and are not meant to assure proper ue draft.
3 ft Min
(91cm)
2 ft Min (61cm)
10 ft Min
(305cm)
2-10-3 RULE
Figure 6A
NOTE: Clearances may only be reduced by means approved by
the regulatory authority having jurisdiction.
WE RECOMMEND that a qualied building inspector and your
insurance company representative review your plans before
installation.
INSTALLATION RECOMMENDATIONS
The Quadra-Fire 5100-I Insert has met and surpassed the most
stringent emissions standards in the United States. The sophistica-
tion of the interior rebox design requires that a proper draft be sup-
plied by the chimney, therefore adherence to the following factors
will enable your insert to operate at its optimum capability.
REQUIRED: A minimum starter pipe reaching to the base of the
existing code approved masonry chimney and an airtight face seal,
but a full chimney liner for factory-built replaces is recommended
for USA and is required in Canada.
BETTER: Direct connection to the rst ue liner in accordance with
the requirements of the NFPA 211.
BEST: A complete relining of the chimney system with a 6 inch
(152mm) diameter listed, stainless liner. Required for factory-built
replace installations in Canada, recommended in USA. The sections
must be attached to the insert and to each other with the crimped
(male) end pointing toward the insert. See Figure 6B. All joints,
including the connection at the ue collar, should be secured with
three sheet metal screws. Make sure to follow the minimum clear-
ances to combustibles as set out on Page 5 of the manual.
These installation instructions describe the installation and opera-
tion of the Quadra-Fire 5100-I Wood Insert. This insert meets the
U.S. Environmental Protection Agency’s 1990 particulate emission
standards. The 5100-I is listed by OMNI-Test Laboratories, Inc.
to UL Safety Standard 1482, and ULC S628, and (UM) 84-HUD.
The 5100-I is approved for mobile home installations when not
installed in a sleeping room and when an outside combustion air
inlet is provided. The structural integrity of the mobile home oor,
ceiling, and walls must be maintained. The insert must be properly
grounded to the frame of the mobile home.
Check with your local building code agency before you begin your
installation to ensure compliance with local codes, including the
need for permits and follow-up inspections. Be sure local building
codes do not supersede UL specications and always obtain a
building permit so that insurance protection benets cannot be
unexpectedly cancelled. If any assistance is required during
installation, please contact your local dealer.
LISTINGS CHIMNEY HEIGHT/DRAFT (CONT’D)
LINER CONNECTOR
FLUE
GAS
DIRECTION
TOWARDS
STOVE
Figure 6B

Page 7
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
IF INSTALLING THIS MODEL TO A MASONRY CHIMNEY, ALWAYS BE SURE THE CHIMNEY IS IN GOOD CONDITION AND
THAT IT MEETS THE MINIMUM STANDARDS OF THE NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) STANDARD 211.
A FACTORY BUILT CHIMNEY MUST BE 6 INCH (152mm) UL 103 HT AND ULC S629.
THIS APPLIANCE IS MADE WITH A 6 INCH (152mm) DIAMETER CHIMNEY CONNECTOR AS THE FLUE COLLAR ON THE
UNIT. CHANGING THE DIAMETER OF THE CHIMNEY CAN AFFECT DRAFT AND CAUSE POOR PERFORMANCE. IT IS NOT
RECOMMENDED TO USE OFFSETS OR ELBOWS AT ALTITUDES ABOVE 4000 FEET ABOVE SEA LEVEL OR WHEN THERE
ARE OTHER FACTORS THAT AFFECT FLUE DRAFT.T SEE PAGE 5.
CAUTION: THIS APPLIANCE IS HOT WHILE IN OPERATION AND MAY REMAIN SO UP TO 40 MINUTES AFTER THERE
IS NO FUEL IN THE FIREBOX. IF THIS APPLIANCE IS IN A HIGH TRAFFIC AREA OR CHILDREN MAY BE NEAR, IT IS
RECOMMENDED THAT YOU PURCHASE A DECORATIVE BARRIOR TO GO IN FRONT OF THE APPLIANCE.
ALTERNATE FLOOR PROTECTION WORKSHEET
How to determine if alternate oor protection materials are acceptable:
All oor protection must be non-combustible (i.e., metals, brick, stone, mineral ber boards, etc.). Any organic materials (i.e., plastics, wood paper
products, etc.) are combustible and must not be used. The oor protection specied includes some form of thermal designation such as R-value
(thermal resistance) or k-factor (thermal conductivity).
PROCEDURE:
1. Convert specication to R-value:
2. Determine the R-value of the proposed alternate oor protector.
i. Use the formula in step (1) to convert values not expressed as “R”.
ii. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the system is greater than the R-value of the specied oor protector, the alternate is acceptable.
EXAMPLE: The specied oor protector should be 3/4 inch thick material with a k-factor of 0.84. The proposed alternate is 4” brick with an r-factor
of 0.2 over 1/8” mineral board with a k-factor of 0.29.
Step (a): Use formula above to convert specication to R-value.
Step (b): Calculate R of proposed system.
= 1
.84
R = x T
1
kx 0.75 = 0.893
Rbrick = 0.2 x 4 = 0.431
4" brick of r = 0.2, therefore: 1/8" mineral board of k = 0.29, therefore:
Rmineral board = 1
0.29
x 0.125 = 0.431
Rtotal = Rbrick + Rmineral board = 0.8 + 0.431 = 1.231
Step (c): Compare proposed system Rtotal of 1.231 to specified R of 0.893. Since proposed system Rtotal is greater than required, the system
is acceptable.
1
k
Btu(in)
ft2(hr)(oF)
= K x 12
(ft2)(hr)(oF)
Btu
R = k = K = r = (ft2)(hr)(oF)
(Btu)(in)
=
Btu(ft)
ft2(hr)(oF)
R = x T
1
k
R = x T
1
K x 12
k-factor is given with a required thickness (T) in inches:
K-factor is given with a required thickness (T) in inches:
r-factor is given with a required thickness (T) in inches: R =
R-value given - no conversion needed.
GENERAL INSTALLATION PROCEDURE
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
• Install liner, if required, for your chosen installation.
• Attach metal warning plate to the back of the replace with screws or nails.
• Set appliance on the hearth (See Hearth Requirements page 5 and Support Kit information on page 16.
• Complete the vent connection required for your installation type.
• Relocate plate for Outside Air (Required for Mobile Home Installation). See page 13. Attach Panel Set to insert and
install Trim Set. See page 15.
• Position unit into replace leaving width enough for berglass batting to be inserted around face seal.
• Work unit securely into the replace using sheet metal shims if leveling bolts are needed. See Figure 12B on page 12.
• Remove all labels from glass prior to building rst re.
• Ensure that plated surfaces are cleaned prior to building rst re. See page 20.
• Read Operation Instructions found on pages 18 and 19.

5100-I WOOD INSERT
Page 8 January 30, 2004
R
250-1960 Rev B
Floor
Ceiling
Caulk
Floor
(second Story)
Non-Combustible
Firestopping
Material
Minimum 1 inch (25mm)
clearance from exterior
chimney to sheathing
Firestopping
2 inch
(51mm)
A chimney must be the required height above the roof
or other obstruction for safety and for proper draft oper-
ation. The requirement is that the chimney must be at
least 3 feet (91cm) higher than the highest point where
it passes through the roof, and at least 2 feet (61cm)
higher than the highest part of the roof or structure that
is within10 feet (305cm) of the chimney, measured hori-
zontally. Refer to Figure 8C.
CHIMNEY REQUIREMENTS
Non-combustible
fire stopping material
Minimum 2 inch (51mm) clearance
from combustible material
and insulation
ceiling
At least 2 ft
(61cm)
At least 3 ft
(91cm)
CHIMNEY HEIGHT
10 ft
(305cm)
CHIMNEY TOP VIEW
FLUE
Foundation
1/2" (12.7mm) airspace
5/8" (16mm)
Fireclay Flue
Liner
Chimney Wall
4" (102mm)
Nominal
Figure 8A Figure 8C
Figure 8B Figure 8D
OVALIZING ROUND STAINLESS STEEL
LINERS
Ovalizing round stainless steel liners to acommodate
the liner passing through the damper region of a re-
place is an allowable and acceptable practice.
Ensure that the ovalization is minimized to the extent
required to t through the damper.

Page 9
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
1. An outside air inlet must be provided for combustion and must
remain clear of leaves, debris, ice and/or snow. It must be
unrestricted while unit is in use to prevent room air starvation
which can cause smoke spillage and an inability to maintain a
re. Smoke spillage can also set off smoke alarms.
2. Unit must be secured to the mobile home structure. Remove
bolts from each side of insert and use plumbers tape to secure
to structure (a washer may be required). Reinstall bolts.
3. Unit must be grounded with #8 solid copper grounding wire or
equivalent and terminated at each end with N.E.C. approved
grounding device.
4. The factory-built fireplace must meet (UM)84-HUD
requirements for outside combustion air supply to the repalce
re chamber and the chimney must be listed to UL103-HT
or a listed UL-1777 full length 6 inch (152mm) diameter liner
must be used. It must be equipped with a spark arrestor cap
and the outside air must be installed on the insert. (See Figure 9A and complete installation instructions
of page 13.)
5. Refer to page 5 of this manual or the Serial label located on the right side of the insert for clearances to
combustibles.
6. Floor protections requirements on page 5 must be followed precisely.
7. Use silicone to create an effective vapor barrier at the location were the chimney or other component penetrates
to the exterior of the structure.
8. Follow the chimney and chimney connector manufacturer’s instructions when installing the ue system for use
in a mobile home.
INSTALLATIONS INTO ZERO CLEARANCE FIREPLACES IN MOBILE HOMES
(IN USA ONLY)
WARNING: NEVER DRAW COMBUSTION AIR FROM A WALL,
FLOOR OR CEILING CAVITY OR FROM ANY ENCLOSED
SPACE SUCH AS AN ATTIC OR GARAGE.
CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL AND CEILING/ROOF MUST BE
MAINTAINED. (i.e., DO NOT CUT THROUGH FLOOR JOIST,
WALL STUD, CEILING TRUSS, ETC.)
WARNING: DO NOT INSTALL IN SLEEPING ROOM.
NOTE: Offsets from the vertical, not exceeding 45°, are allowed per Section 905(a) of the Uniform Mechanical Code
(UMC). Offsets greater than 45° are considered horizontal and are also allowed, providing the horizontal run does
not exceed 75% of the vertical height of the vent. Construction, clearance and termination must be in compliance
with the UMC Table 9C. This installation must also complies with NFPA 211.
NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5’ (405cm) from ground level
for transportation purposes.
9. Burn wood only. Other types of fuels may generate poisonous gases (e.g., carbon monoxide).
Figure 9A - Installing Outside Air
Remove 2 Spring Handles
Cover from rear of
stove is secured
to front of stove
See complete
instructions on
page 13
Spark Arestor Cap
Roof Flashing
Storm Collar
Joist Shield/Firestop Double Wall
Connector Pipe

5100-I WOOD INSERT
Page 10 January 30, 2004
R
250-1960 Rev B
MASONRY FIREPLACE
USING DIRECT-CONNECT METHOD
Refer to: Clearances to Combustibles on page 5, Canadian Installation requirements on page 12,
Hearth Requirements on page 5 and Zero Clearance Adjustable Support Kit on page 16.
Figure 10A - Installation Into Masonry Fireplace
Direct Connect
Seal Option
Minimum Starter
Pipe Option
Full Listed
Liner Option
Masonry Chimney
Flue Tile
Mantel
Air-tight Face Seal
Damper Area
SEAL DAMPER AREA OR FACE SEAL
INSTALLATION OPTIONS
The Quadra-Fire 5100-I Insert conforms with the UL Stan-
dard for Safety 1482 and ULC S628 (Canada) in all respects,
and is approved to UL & ULC safety standards for installa-
tion and use within a replace with a masonry chimney in
accordance with NFPA No. 211, with or without a direct ue
collar connection. A starter pipe is required to reach to the
bottom of the existing ue.
1. Secure the replace damper in the open position. If this
cannot be accomplished, it will be necessary to remove the
damper.
2. Seal either the damper area around the chimney liner
with a high temperature sealant or the replace front with
berglass batting.
3. The chimney should be examined for cracks, loose mortar,
and other signs of deterioration and blockage. The insert
should not be installed until it is determined that the chim-
ney is safe for use. Since an oversized ue contributes to
the accumulation of creosote, the size of the ue should be
checked to determine that it is not too large for the insert.
The chimney should also be checked to ensure it meets the
minimum standard of the National Fire Protection Associa-
tion (NFPA) Standard 211. The following bullets list the more
critical requirements for a properly constructed chimney:
• The masonry wall of the chimney, if brick or modular
block, must be a minimum of 4 inches (102mm) nominal
thickness. A chimney of rubble stone must be at least 12
inches (305mm) thick
• The chimney must have a re clay ue liner (or equiva-
lent) with a minimum thickness of 5/8” (16mm) and must be
installed with refractory mortar. An equivalent liner must be
a listed chimney liner system or other approved material.
• A chimney inside the house must have at least 2 inches
(51mm) of clearance to the combustible structure. A chim-
ney outside the house must have at least 1 inch (25mm)
clearance to the combustible structure. Non-combustible re
stops must be installed at the spaces where the chimney
passes through oors and/or ceiling (See Figure 8A and 8B
on page 8).
NOTE: In Canada, a full reline is required.
METAL HEAT CIRCULATING MASONRY
The Quadra-Fire 5100-I Insert conforms with the safety
standard UL-1482 and ULC S628 (Canada) in all respects
and is approved to UL & ULC safety standards for instal-
lation and use within a replace with masonry chimney, in
accordance with NFPA No. 211, with or without a direct ue
collar connection. A starter pipe is required into existing
chimney.
Figure 10B - Installation Into Metal Heat Circulating
Showing Use Of Starter Pipe
Listed Liner
Mantel
SEAL DAMPER AREA OR FACE SEAL

Page 11
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
FACTORY BUILT ZERO CLEARANCE FIREPLACE
(USA INSTALLATONS ONLY)
The Quadra-Fire 5100-I Insert is listed to UL Standards for Safety 127 and approved for installation and use in factory built
zero clearance replaces conforming to the following specications:
The following modications of factory built replaces are permissible: 1) removal of damper; 2) removal of smoke shelf
or bafe; 3) removal of ember catches; 4) removal of re grate; 5) removal of viewing screen/curtain; and, 6) removal of
doors.
NOTE: Installation into replaces without a permit will void the listing.
The factory built chimney must be listed per UL 127 and meet the type HT requirements of UL 103. Factory built replace
chimneys tested to UL 127-1998, may be at the replace manufacturer’s option, tested to the same criteria as UL 103 HT
requirements. If the chimney is not listed as meeting HT requirements, or if the factory built replace was tested prior to
1998, a full height listed chimney liner must be installed from the appliance ue collar to the chimney top. The liner must
meet type HT requirements (2100ºF) per UL 1777. The liner must be securely attached to the insert ue collar and the
chimney top. To prevent room air passage to the chimney cavity of the replace, seal either the damper area around the
chimney liner with high temperature sealant or the replace front with berglass batting.
The replace must not be altered, except that the damper may be removed to accommodate a direct-connect starter pipe
or chimney liner, and external trim pieces which do not affect the operation of the replace may be removed providing
they can be stored on or within the replace for reassembly if the insert is removed. The permanent metal warning label
provided must be attached to the back of the replace, with screws or nails, stating that the replace may have been
altered to accommodate the insert, and must be returned to
original condition for use as a conventional replace.
If the hearth extension is lower than the replace opening,
the portion of the insert extending onto the hearth must be
supported. Manufacturer designed adjustable support kit
can be ordered from your dealer. (See page 16).
Final approval of this installation type is contingent upon
the authority having jurisdiction.
Listed Liner
Mantel
SEAL DAMPER AREA OR FACE SEAL
Figure 11A - Installation Into A Factory Built
Zero Clearance Fireplace
36”
24”
19”
915mm
610mm
483mm
Minimum Width of cavity opening:
Minimum Height:
Minimum Depth from front to rear:

5100-I WOOD INSERT
Page 12 January 30, 2004
R
250-1960 Rev B
INSTALLATION IN CANADA
MASONRY and HEAT-CIRCULATING
(INSTALLATIONS INTO FACTORY-BUILT FIREPLACES ARE PROHIBITED IN CANADA)
Whether installed in a masonry or heat-circulating replace, this replace insert must be installed with a continuous chim-
ney liner of 6” (152mm) diameter extending from the replace insert to the top of the chimney. The chimney liner must
conform to the Class 3 requirements of CAN/ULC-S635, Standard for Lining Systems for Existing Masonry or Factory-Built
Chimneys and Vents, or CAN/ULC-S640, Standard for Lining Systems for New Masonry Chimneys.
• Do not remove bricks or mortar from replace to accommodate insert.
• The face of the replace must be sealed to prevent room air passage into the chimney cavity.
• The permanent metal warning label provided must be afxed to the back of the replace with screws or nails
to the replace, in a location readily visible should the replace insert by removed, stating that the replace may
have been altered to accommodate the insert, and must be returned to original condition for use as a conventional
replace.
USE OF LEVELING BOLTS
Figure 12A
Two leveling bolts, 3/8” x 4” are shipped inside the component pack found inside the rebox.
NOTE: Not all installations will require the use of the leveling bolts. If the leveling bolts are necessary, you will also need
sheetmetal guides placed under the leveling bolts to slide insert into position.
1. Remove the bolts from the component pack.
2. Locate the weld nuts welded to each side of the insert bottom and insert the bolts.
3. Position insert on hearth with rear of insert extending into replace opening.
4. Extend leveling bolts downward to level insert.
SECURING LINER TO CHIMNEY RING
There are two options to secure the liner to the chim-
ney ring: (See Figure 12A).
Option One: If there is enough room on the top of the
insert to work, hand bend the two tabs upward 90°.
Secure the liner with the supplied hex head bolts 1/4-
20-3/4.
Option Two: Remove the manifold tubes, berboard
bafe and ceramic blanket. From inside the rebox,
pull liner down through the chimney ring below the
outer skin. There are two pre-drilled holes in the chim-
ney ring 180° apart. Secure the liner with the supplied
hex head bolts 1/4-20-3/4.
NOTE: Tabs are shipped from factory in a at position.
Bend upwards 90 degrees.
Attach liner with 2 tabs
2 pre-drilled holes on
chimney ring under outer skin
(access through firebox)

Page 13
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
NOTE: The 5100-I requires replacement of combustion air. If your home is fairly air-tight, it is receommend that
you install outside air. If you are installing into a Mobile Home, outside air is required. See page 9.
OUTSIDE AIR INSTALLATION
Figure 13A
Tools Needed: Phillips Head Screwdriver
1) Remove cover from rear of stove by removing screws.
2) Remove the 2 Air Control spring handles.
3) Remove the lower grill by removing 2 screws in the center of the grill.
4) Unplug the snap disc by-pass switch and speed control from the wiring harness for easier access to blower.
(Located on right hand side of stove as you face the unit).
5) Mount the cover you removed from the back to the front to block room air from entering through the front lower grill.
6) Re-connect snap disc & speed control to wiring harness and replace screws in blower frame.
7) Reinstall lower grill, replace screws & spring handles.
8) Push insert back into the replace.
9) Plug blower cord back into outlet.
Remove 2 Spring Handles
Cover from rear
of stove is
secured to front
of stove
BLOWER CORD LOCATION
The 5100-I Insert comes standard with 2 blowers, installed at the factory with blower cord on right side of insert (as you face
the unit). The blower cord can also be installed on the left side. Disconnect the cord from right side and reinstall on the left
side. ROUTE WIRES BEHIND THE BLOWER. Do not route cord under or in front of appliance.
BLOWER OPERATION
The 5100-I is equipped with a 110°thermally operated snap disc which will automatically turn on the blower when the insert
reaches this temperature. The snap disc is located at the center of the insert, under the lower grille. There is a manual
override switch on the right side of the insert. The blower can be controlled manually by switching this switch to ON and
operating the blower with the speed control. If the blower does not come on automatically when the stove reaches a suf-
cient temperature, the snap disc might be bad and should be replaced.

5100-I WOOD INSERT
Page 14 January 30, 2004
R
250-1960 Rev B
BLOWER REPLACEMENT INSTRUCTIONS
Part 832-1991 for Serial Numbers 131586 and below
Part 832-3190 for Serial Numbers 131587 and above
Figure 14A
NOTE: When the speed control is turned clockwise, it will click on to high speed. Continue to turn the speed control
clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop.
1. With the unit plugged in, turn the Speed Control Knob to slow. (Full clockwise.)
2. Use a small screwdriver to adjust the fan speed by turning the adjustment mechanism through the hole on the
side of the Speed Control.
3. Adjust the speed so the fan runs slowly but does not stop. Turn clockwise to slow the fan and counterclockwise
to increase the speed.
FAN SPEED CONTROL ADJUSTMENT, IF NECESSARY*
*The fan Speed Control for this unit is adjusted at the factory, and normally does not require further
adjustment.
Remove 2 Spring Handles
TOOLS NEEDED: #2 PHILLIPS SCREWDRIVER
1) Unplug blower cord from outlet.
2) Pull insert out from the replace.
3) Remove the 2 Air Control spring handles.
4) Remove the lower grill by removing 2 screws in the center of
the grill.
5) Unplug the snap disc by-pass switch and speed control from
the wiring harness for easier access to blower. (Located on
right hand side of stove as you face the unit).
6) Remove screws from blower frame on side of insert.
7) Blower will then slide out through side of insert.
8) Install new blower in same fashion.
9) Re-connect snap disc & speed control to wiring harness and
replace screws in blower frame.
10) Re-install lower grill, replace screws & spring handles.
11) Push insert back into the replace.
12) Plug blower cord back into outlet.
LEFT FAN
AUX POWER
LEFT
RIGHT FAN
POWER IN
SPEED
CONTROL
SNAP DISC
BY-PASS SWITCH
SNAP DISC
Small Red Female Small Red Female
Small Red Female
Small Red Female
Large Blue Male
Large Blue Male
Lar
g
e Red Female
Large Red Female
Large Red Female
Large Red Female
Large Blue Male
Large Blue Female
Large Blue Female Large Blue Female
Figure 14B
WIRING DIAGRAM

Page 15
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
STANDARD Size: 30-1/2” h x 47”w
831-1452, Gold Trim
SP-51S-NL, Nickel Trim
Figure 15A
Figure 13B
Do not tighten sides until
top is locked into place
Panel brackets
View of "L" Bracket
installed
Kit Includes: ( 2) Side Panels, left & right; (1) Panel Top & Fastener package; (2) Side Trim, left & right; (1) Trim Top & Fastener package.
Tools Needed: Powered Phillips head screw driver and a long handled Phillips screw driver .
1. Loosely install the 2 side panels, do not tighten, using the
cage nuts already attached to the stove. (Note: The sides are
not interchangeable).
2. Put top panel in place pushing straight back and then to the
right to lock onto top of side panels. Attach the top panel
to the sides using the screw already installed at the top of
side panels and the panel brackets included in the fasteners
package.
3. Tighten side panels to the stove using a long handle screw
driver. See Figure 15B.
Figure 15C
Back view of top
and side panel
assembled
PANEL and TRIM SET INSTALLATION
Attaching Panels to the Insert
LARGE Size: 34-1/4” h x 51-1/4”w
831-1461, Gold Trim
SP-51l-NL, Nickel Trim
1. Place protective covering on surface to be used to assemble
the trim pieces. Lay the trim face down.
2. Attach the 2 side trim pieces to the top trim at each corner
using the “L” bracket included in fasteners package. Slide
assembled trim over panel set. See Figure 15C.
Assembling Trim

5100-I WOOD INSERT
Page 16 January 30, 2004
R
250-1960 Rev B
ZERO CLEARANCE ADJUSTABLE TRIM SUPPORT, 2” to 10”
Part No. ADJSPT-12, size 12” x 50”
Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides, Double-Sided Tape (already installed)
Tools Needed: Phillips Head Screwdriver, Sheet Metal Shears, Measuring Tape, Gloves
1. The 10 screws on each set of scissors will already be
loose when shipped. See Figure 16A.
2. Expand scissors to desired height. Tighten screws
to hold in place using Phillips Head screwdriver. See
Figure 16B.
3. Measure front and side trims to required height to cover
scissors and mark pieces for cutting. Cut excess mate-
rial from top of trim’s edge, not bottom. This edge will be
sharp; wear gloves to prevent injury to your hands. See
Figure 16B.
4. Using sheet metal shears, cut trim along the marked
edge. The cut edge ts under lip of top trim, so it allows
for some variance in your straight edge.
5. The double-sided tape that holds front and side trims
to scissors has a particularly powerful bonding adhe-
sive. Adjustments are extremely difcult once trim has
adhered to tape. Do a dry run rst without removing
paper from tape.
6. Place cut edge of trim under top lip and into position on
scissors. Place side pieces on rst and then front piece.
The front piece overlaps side pieces. NOTE: The trim in
the Flush Mount Kit is one piece.
7. Once you are satised with the positioning, remove trim
and set aside.
8. Remove the paper from double-sided tape that is to
accept trim side. Align side and then press hard against
tape to secure side piece. Repeat for other side. Install
front trim piece last.
NOTE: 3/8” ( 9.5mm) thick tile or like material can be cut to
size and t under lip of top trim edge for a decorative touch.
See Figure 16C.
DOUBLE-SIDED TAPE
DOUBLE-SIDED TAPE
EXPLODED VIEW OF SCISSORS
SCREWS ARE CIRCLED
Figure 16A
Figure 16B
Figure 16C
INSTALL FRONT TRIM LAST.
CORNERS OVERLAP SIDE
TRIM PIECES
EXPAND SCISSORS TO DESIRED
CUT TOP EDGE OF TRIM,
NOT BOTTOM EDGE
Decorative tile may
be installed
Figure 16D

Page 17
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
WOOD SELECTION AND STORAGE
Burn only dry seasoned wood. Dry, well-seasoned wood will not only minimize the chance of creosote formation but will give you the
most efcient heat output. Even dry wood contains at least 15% moisture by weight and should be burned hot enough to keep the
chimney hot enough to maintain particulate (smoke) burning. Burning unseasoned wood of any variety defeats the stoves’ efciency.
Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing wood can be considered to be
about two-thirds seasoned. Wood is dry enough to burn if the ends of the logs have cracks radiating in all directions from the center. If
your wood sizzles in the re, even though the surface is dry, it may not be fully cured.
Drying time can be reduced by splitting wood prior to storage. Since the majority of drying occurs through the cut ends rather than the
sides, stack the wood so both ends of each piece are exposed to air. Store wood under cover, such as in a shed, or covered with a tarp,
plastic, tarpaper, sheets of scrap plywood, etc.
OVERFIRING
Do not overre. Overring can result in crazing, an effect causing a white, non-removable lm to be deposited on the inside of the glass.
Using ammable liquids or too much wood, or burning trash in the insert, may result in overring. If the chimney connector or insert
glows red, or worse, white, the insert is overred. This condition may ignite creosote in the chimney, possibly causing a house re. If any
part of the insert starts to glow, you are in an overre situation. If you overre, immediately close the insert dampers and door, if open,
to reduce the air supply to the re. Overring your insert voids your warranty.
NOTE: The special high temperature nish paint applied to the insert will cure as your insert heats. You will notice an odor
and perhaps see some vapor rise from the insert surface, this is normal. We recommend that you open a window until the odor
dissipates and the paint is cured.
OPERATION
Before lighting your rst re in the insert, make certain that the bafe is correctly positioned. It should be resting against the rear support.
Also refer to care and cleaning of gold/nickel plated surfaces on cover page before lighting your rst re.
CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar liquids to start or “freshen
up” a re in this heater. Keep all such liquids well away from the heater while it is in use.
There are many ways to build a re. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling,
which in turn ignites the slow-burning rewood. Here is one method that works well:
1. Place several wads of crushed paper on the firebox floor. Heating flue with slightly crumpled newspaper before adding
kindling keeps smoke to a minimum.
2. Place several wads of crushed paper on the rebox oor.
3. Open Start-Up Air Control (right side) and Primary Air Control (under ashcatcher) fully. See Figure 19A on page 19.
4. Ensure that no matches or other combustibles are in the immediate area of the insert, that the room is adequately ventilated,
and the ue is unobstructed.
5. Light the paper in the insert. NEVER light or rekindle insert with kerosene, gasoline, or charcoal lighter uid; the results
can be fatal.
6. Once the kindling is burning quickly, add several full-length logs 3” (76mm) or 4” (102mm) in diameter. Be careful not to
smother the re. Stack the pieces of wood carefully: near enough to keep each other hot, but far enough away from each
other to allow adequate air ow between them.
7. When ready to reload the insert, add more logs. Large logs burn slowly, holding a re longer. Small logs burn fast and
hot, giving quick heat.
8. Adjust the Start-Up Air Control and Primary Air Control, maintaining ames above the fuel. The more you close down the Primary
Control, the lower and slower the re will burn. The more you open the Primary Control the more heat will be produced. The Start-Up
Air Control (right side) is only used for the rst 5 to 15 minutes.
As long as there are hot coals, repeating steps 7 and 8 will maintain a continuous re.
BUILDING A FIRE
NOTE: Remove all labels from glass front prior to lighting the rst re.

5100-I WOOD INSERT
Page 18 January 30, 2004
R
250-1960 Rev B
BURN RATES
STARTING FIRE: Open both controls (push in) completely. After a wood load has been burning on high for 5 to 15 minutes or longer for
very large pieces, close the Start-Up Air Control (right side) by pulling it out.
HIGH: Leave the Primary Air Control fully open (under ashcatcher). It is especially important to fully open both controls when reloading
the insert as failure to do so could result in excessive emissions, also referred to as ‘opacity’.
After a wood load has been burning on high for 5 to 15 minutes on High to achieve the following burn rates set the
controls as listed below:
MEDIUM HIGH: Close the Primary Air Control to 1” to 2-1/2” (25mm to 64mm) open. Start-Up Air is closed.
MEDIUM: Close the Primary Air Control to 3/4” to 1” (19mm to 25mm) open. Start-Up Air is closed.
LOW: Gradually close down the Primary Air Control by pulling out making sure to maintain ames in the insert. (Start-Up Air is closed).
It is very important to maintain ames in your insert during the rst few hours of a low burn to avoid excessive air pollution.
OPACITY
Opacity is the measure of how clean your insert is burning and is measured in percentages. An opacity of 100% in the smoke column
from a chimney will totally obscure an object. Whereas 0% opacity means that no smoke column can be seen. A periodic check of the
opacity emitted from your chimney will enable you to burn your insert as smoke free as possible.
1. Initial (cold) startup: Leave fan off until your insert is hot and a good coal bed is established, approximately 30 minutes after fuel
is lit.
2. High Burn Setting: The fan may be left on throughout the burn.
3. Medium or Medium High Burn Setting: The fan should be left off until a good burn is established, then turned on a medium
or high rate.
4. Low Burn Setting: The fan tends to cool the insert. Leave fan off until the burn is well established; then, if you wish, turn the fan
on at a low rate.
5. The fan is equipped with a rheostat (speed control). The highest fan speed is obtained by turning the rheostat on, then adjusting back
towards “OFF” as far as possible without turning the fan off. For a low fan speed, turn the control knob clockwise as far as possible.
Remove cold ashes (not hot) from the insert at regular intervals, depending on your usage. Ashes should be placed in a metal container
with a tight tting lid. The closed container of ashes should be placed on a non-combustible oor or on the ground, well away from all
combustible materials, pending nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be
retained in the closed container until all cinders have thoroughly cooled. Always treat ashes as if they contain hot coals.
ASH REMOVAL
FAN OPERATING INSTRUCTIONS
BTU / Hr
Below 10,000
10,000 - 15,000
15,000 - 30,000
Maximum Heat
Start-Up Air Control
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
Primary Control
Pull to Stop
3/4” - 1” open
1” - 2-1/2” open
Fully open
WARNING: Do not operate with Start-Up
Air Control in the open position in excess
of 15 minutes! Risk of extreme tem-
peratures! Prolonged operation of this
stove with the Start-Up Air Control in the
open position may cause the combusti-
ble materials around the stove to exceed
safe temperature limits.
OPERATING TIPS
For maximum operating efciency with the lowest emissions, follow these operating procedures:
1. Regardless of desired heat output, when loading stove, burn your Quadra-Fire with both air controls wide open for a minimum
of 5 to 15 minutes.
2. Regulate burn rate (heat output) by using the Primary Control (under ashcather). The Start-Up Air Control (right side) is mainly
for initial start-up and reloading.
3. Heat output settings: Follow burn rate instructions listed below.
4. Burn only dry, well-seasoned wood.
These are approximate settings, and will vary with type of wood or chimney draft.

Page 19
January 30, 2004
5100-I WOOD INSERT
R
250-1960 Rev B
AIR QUALITY AND YOUR QUADRA-FIRE INSERT
In recent years there has been an increasing concern about the quality of our air. Much of the blame for poor air quality has
been placed on the burning of wood for home heating. In order to improve this situation we at Quadra-Fire have developed
cleaner burning inserts that surpass the stringent requirements for emissions established by our governing agencies. Your
4100-I, like any other appliance, must be properly operated in order to ensure that they perform the way they are designed
to perform. Improper operation and maintenance may cause any wood burning unit to release more particulate, adversely
affecting the environment.
The story of the Three Burning Stages . . .
It helps to know a little about the actual burn process, which entails three discernible burning stages. The rst stage is called
the kindling stage. During this stage the fuel reaches the boiling temperature of water, 212°F, evaporating the moisture
found to some degree in all wood.
Because the process takes heat from the insert during this initial drying stage, each new load of wood reduces the chances
for a good, clean burn. For this reason it is always best to burn dry, seasoned rewood, and operate the controls properly.
The bottom control on the right side of your insert is called the Start-Up Air Control and is used primarily during this rst
kindling stage of burning.
During the secondary stage, the wood gives off ammable gases which burn above the fuel with bright ames. These
ames above the fuel must be maintained until the third stage to ensure proper burning. During this stage you may adjust
your insert for a low burn rate. To achieve a low burn rate it is necessary to close down the air while still maintaining some
ames. If the ames tend to go out, the setting is too low. The Primary Control will assist you in adjusting the insert for a
low burn rate.
The third stage of burning is the charcoal stage. This happens when the ammable gases have been burned and the
charcoal remains. The coals burning with hot blue ames is a naturally clean portion of the burn. It is very important to
reload your insert while enough lively hot coals remain in order to provide the amount of heat needed to dry and rekindle
the next load of wood. Open up both controls for a short while before reloading to liven up the coal bed. You should also
break up any large chunks and distribute the coals so the new wood is laid on hot coals. Leave both controls open until
the new wood load is burning well enough to maintain the secondary stage of burning and then set controls to your desired
heat output setting.
START-UP AIR SYSTEM
The combustion air enters at the rear of the rebox through the rear air tubes. This air supply is controlled by the Start-Up
Air Control. See Figure 19A.
PRIMARY AIR SYSTEM
The primary air enters at the upper front of the rebox near the top of the glass door. This preheated air supplies the neces-
sary fresh oxygen to mix with the unburned gases, helping to create secondary, tertiary and quaternary combustion. This
air is regulated by the Primary Air Control. For more primary air (more heat), push rod in. For less primary air (less heat),
pull rod out. See Figure 19A.
In other words . . .
Pulling either control towards you closes off the air available to the insert in that area. Pushing either control opens it, allow-
ing air circulation to the area. A good analogy to remember for this procedure is the gas pedal on your car. Pushing in the
gas pedal makes the engine run faster. Letting off (pulling the control back) makes the car run slower.
Primary Air Control Start-Up Air Control
Figure 19A
OPEN - PUSH IN
CLOSE - PULL OUT

5100-I WOOD INSERT
Page 20 January 30, 2004
R
250-1960 Rev B
MAINTENANCE
CARE AND CLEANING OF PLATED SURFACES
IMPORTANT: You must clean all the ngerprints and oils from the plated surfaces before ring the insert for the rst time.
Use warm soapy water and a soft rag, glass cleaner and a paper towel, or vinegar and a paper towel to remove the oils.
DO NOT use abrasive cleaners! If not cleaned properly prior to lighting the rst re, the oils can cause permanent stains.
The plating will be cured upon ring of the insert and oils will no longer affect the nish. Subsequently, little maintenance
is then required. Wipe clean as needed with a soft towel.
CARE AND CLEANING OF GLASS
NOTE: Remove all labels from glass prior to lighting the rst re.
Quadra-Fire inserts are equipped with super heat resistant ceramic glass which can only be broken by impact or misuse.
Clean glass with any non-abrasive glass cleaner. Abrasive cleaners may scratch and cause glass to crack. Inspect glass
regularly. If you nd a crack or break, immediately put the re out and return the door to your authorized dealer for replace-
ment of glass before further use. Do not substitute materials for glass replacement.
GLASS REPLACEMENT INSTRUCTIONS
Replace with 5mm ceramic glass only
1. Remove door from insert and lay on a padded at surface.
2. Remove glass retainer screws using a Phillips screwdriver.
3. Lift glass out of the door frame and/or side frames.
4. Lay new glass with berglass tape around it into door frame and/or side frames.
5. Place glass retainers over the berglass tape on the edges of the glass and re-install screws. Be sure glass
is centered in the opening (i.e. same space top and bottom, left and right).
6. Tighten screws enough to hold frame and glass in place.
7. Check again for centering of glass in door and/or side frames and give all screws a nal tightening.
CREOSOTE FORMATION AND NEED FOR REMOVAL
When wood is burned slowly it produces tar and other organic vapors which combine with expelled moisture, and, in turn
forms creosote. These creosote vapors condense in the relatively cool chimney ue when a re is newly started, or from a
slowly burning re, and accumulate on the ue lining of the chimney.
A build up of creosote can then be ignited by sparks rising up the chimney. When ignited, this situation makes an extremely
hot re which may damage the chimney and even destroy your home. The chimney connector and chimney should be
inspected at least once every two months during the heating season to determine if a creosote buildup has occurred. It is
extremely important that this residue is removed at regular intervals, usually once a year depending on your burning habits,
to prevent the occurrence of a chimney re. It is highly recommended that you contact a professional chimney cleaner for
this area of maintenance.
CHIMNEY
If your type of installation involves a full reline of the chimney, it will be necessary to either remove the bafe from the insert,
or remove the insert from the replace and disconnect the vent prior to cleaning the chimney. Refer to page 21 in this
manual for instructions on Bafe Brick Removal.
If your type of installation is direct connect within a masonry chimney, the insert will need to be pulled out from the replace
and disconnected from the ue prior to cleaning the chimney. The creosote can either be caught in a large garbage bag
secured to the pipe or swept and vacuumed out of the replace. Reconnect the pipe and reinstall the insert following instal-
lation instructions in this manual on page 10.
WARNING! DO NOT CLEAN GLASS WHEN HOT.
WARNING! DO NOT SLAM INSERT DOOR OR
IMPACT THE GLASS WHEN CLOSING THE DOOR.
MAKE SURE THAT LOGS DO NOT PROTRUDE
AGAINST THE GLASS.
WARNING! DO NOT OPERATE WITH BROKEN
GLASS.