Quadra-Fire CLASSIC BAY 1200 User manual

1June 4, 20197027-801C
R
CLASSIC BAY 1200 PELLET
APPLIANCE
MODEL:
CB1200-C
Installation Manual
Installation & Appliance Set-Up
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT DISCARD THIS MANUAL
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
CAUTION
Tested and approved for wood pellets and shelled eld
corn fuel only. Burning of any other type of fuel voids
your warranty.
NOTE: To obtain a French translation of this
manual, please contact your dealer or visit
www.quadrare.com
REMARQUE : Pour obtenir une traduction française de
ce manuel, s’il vous plaît contacter votre
revendeur ou visitez www.quadrare.com
If the information in these instructions is
not followed exactly, a re could result
causing property damage, personal injury,
or death.
WARNING
• Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
• Do not over re - If appliance or chimney connector
glows, you are over ring. Over ring will void
your warranty.
• Comply with all minimum clearances to combustibles
as specied. Failure to comply may cause house re.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
WARNING
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high
temperatures
• High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other
ammable materials away.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, re o󰀩cials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.

2June 4, 20197027-801C
CB1200 Free Standing
TABLE OF CONTENTS
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
1 Important Safety Information............. 3
A. Appliance Certication........................3
B. BTU & E󰀩ciency Specications ................3
C. Glass Specications .........................4
D. Electrical Rating ............................4
E. Mobile Home Approved .......................4
F. Non-Combustible Materials ....................4
G. Combustible Materials .......................4
H. Sleeping Room .............................4
I. California - Prop65 ...........................4
2 Getting Started .................................... 5
A. Design, Installation & Location Considerations .....5
B. Thermostat Wall Control Location ...............6
C. Tools And Supplies Needed ...................6
D. Inspect Appliance and Components .............6
E. Install Checklist .............................7
3 Dimensions and Clearances.............. 8
A. Appliance Dimensions ........................8
B. Clearances to Combustibles (UL and ULC) ......10
C. Hearth Pad Requirements (UL and ULC) ........11
D. Alcove ...................................12
4 Vent Information................................ 13
A. Venting Termination Minimum Requirements .....13
B. Avoiding Smoke and Odors...................14
C. Draft ....................................14
D. Negative Pressure..........................15
E. Chimney and Exhaust Connection .............15
F. Equivalent Feet of Pipe ......................16
G. Pipe Selection Chart ........................16
5 Venting Systems ............................... 17
A. Through The Wall ..........................17
B. Vertical into Existing Class A Chimney ..........18
C. Through The Wall & Vertical - Exterior ..........18
D. Vertical - Interior - Typical Installation . . . . . . . . . . .18
E. Masonry..................................19
F. Alternate Masonry ..........................19
6 Appliance Set-Up .............................. 20
A. Outside Air Kit Instructions ...................20
B. Top Vent Adapter Installation..................21
C. Rear Vent & Rear Vent to Top Vent Adapter ......21
D. Thermostat Installation and Operation ..........21
E. Optional Log Set Placement Instructions ........23
F. Installing Logo .............................23
7 Mobile Home Installation.................. 24
8 Accessory List .................................. 25
A. Service & Maintenance Log ..................25
B. Accessory List .............................26

3June 4, 2019 7027-801C
CB1200 Free Standing
Model CB1200 Pellet Appliance
Laboratory OMNI Test Laboratories, Inc.
Safety
Report No. 061-S-21-4
Type Solid Fuel Room Appliance/Pellet Fuel
Burning Type
Standard
ASTM E1509-04, ULC S627-00 and
ULC/ORD-C1482-M1990 Room
Appliance Pellet Fuel Burning type and
(UM) 84-HUD, Mobile Home Approved.
Emissions Report No: 0061PS013E
EPA Certication #: 176-19
EPA Certied Emissions: 1.1 grams per hour
*LHV Tested E󰀩ciency: 77.8%
**HHV Tested E󰀩ciency: 72.7%
***EPA BTU Output: 11,100 - 30,900 / hr
****BTU Input: 15,900 - 41,100 / hr
Vent Size: 3 or 4 inches “L” or “PL”, or
6 inches
Hopper Capacity: 80 lbs.
Fuel: Premium Wood Pellets
*Weighted average LHV (Low Heating Value) e󰀩ciency
using data collected during EPA emissions tests.
**Weighted average HHV (High Heating Value) e󰀩ciency
using data collected during EPA emissions tests.
***A range of BTU outputs calculated using HHV
e󰀩ciency and the burn rates from the EPA tests.
****Based on the maximum feed rate per hour multiplied
by approximately 8600 BTU’s which is the average BTU’s
from a pound of pellets.
‡ Grade of pellet fuel as certied by Pellet Fuels Institute (PFI), ENPlus
or CANplus.
1 Important Safety Information
NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM
E1509-04, ULC S627-00, (UM) 84-HUD and ULC/ORD-C-1482.
A. Appliance Certication B. BTU & E󰀩ciency Specications
This pellet appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate
this pellet appliance in a manner inconsistent with operating instructions in this manual.
This Classic Bay 1200 is
Certied to comply with 2020
particulate emission standards.

4June 4, 20197027-801C
CB1200 Free Standing
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
C. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please contact
your dealer for replacement glass.
F. Non-Combustible Materials
Material which will not ignite and burn, composed of any
combination of the following:
- Steel
- Plaster
- Brick
- Iron
- Concrete
- Tile
- Glass
- Slate
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace of 750° C.
D. Electrical Rating
115 VAC, 60 Hz, Start 3.75 Amps, Run 1.88 Amps
E. Mobile Home Approved
• This appliance is approved for mobile home
installations when not installed in a sleeping room and
when an outside combustion air inlet is provided.
• The structural integrity of the mobile home oor, ceiling,
and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home and use only Listed pellet vent
Class “L” or “PL” connector pipe.
• Outside Air Kit, part 811-0570 or 811-0872 must be
installed in a mobile home installation.
G. Combustible Materials
Material made of/or surfaced with any of the
following materials:
- Wood
- Compressed Paper
- Plant Fibers
- Plastic
- Plywood/OSB Sheet Rock (drywall)
Any material that can ignite and burn: ame proofed or not,
plastered or non-plastered.
H. Sleeping Room
When installed in a sleeping room it is recommended that
3ft of vertical be installed prior to horizontally exiting the
room and a smoke/CO alarm be installed in the bedroom.
The size of the room must be at least 50ft³ per 1,000 Btu/hr
stove input, if the stove exceeds the room size, outside air
must be installed.
I. California - Prop65
WARNING
This product and the fuels used to operate this product (wood), and
the products of combustion of such fuels, can expose you to
chemicals including carbon black, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to
the State of California to cause birth defects or other reproductive
harm. For more information go to: WWW.P65Warnings.ca.gov
NOTE: Hearth & Home Technologies, manufacturer
of this appliance, reserves the right to alter
its products, their specications and/or price
without notice.
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth &
Home Technologies.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
• Operating appliance without fully assembling
all components.
• Operating appliance without legs attached (if
supplied with appliance).
• Do NOT Over re - If appliance or chimney connector
glows, you are over ring.
Any such action that may cause a re hazard.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:

5June 4, 2019 7027-801C
CB1200 Free Standing
Install Guide
2 Getting Started
Recommended
Location
Marginal
Location
Location
Not
Recommended
Recommended
Location
Location NOT
Recommended
Multi-level Roofs
Windward
Leeward
Outside Air Kit Termination Cap
Figure 5.1
A. Design, Installation & Location
Considerations
1. Appliance Location
Since pellet exhaust can contain ash, soot or sparks, you
must consider the location of:
- Windows
- Air Intakes
- Air Conditioner
- Overhang, so󰀩ts, porch roofs, adjacent walls
- Landscaping, vegetation
- Horizontal or vertical vent termination
2. Floor Support
The supporting oor under the appliance must be able to
handle the weight of the appliance, fuel load and the weight
of the chimney.
Ensure that your oor will support these weights prior to
installation. Add su󰀩cient additional support to meet this
weight requirement prior to installation. The weight of the
appliance is 238 lbs.
WARNING
Risk of Fire.
Damaged parts could impair safe operation. Do NOT
install damaged, incomplete or substitute components.
NOTICE: Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building inspector,
re o󰀩cials or authorities having jurisdiction over
restrictions, installation inspection and permits.
It is a good idea to plan your installation on paper, using
exact measurements for clearances and oor protection,
before actually beginning the installation. Location of the
appliance and chimney will a󰀨ect performance.
Consideration must be given to:
- Safety, convenience, tra󰀩c ow
- Placement of the chimney and chimney connector
and to minimize the use of chimney o󰀨sets.
- Place the appliance where there will be a clear
passage for a Listed chimney through the
ceiling and roof (vertical) or through exterior
wall (horizontal).
- Installing the required outside air kit will a󰀨ect the
location of the vent termination.
When locating vent and venting termination, the ideal
location is to vent above roof line when possible. This
minimizes the a󰀨ects of wind loading.

6June 4, 20197027-801C
CB1200 Free Standing
Tools and building supplies normally required
for installation, unless installing into an existing
masonry replace:
- Reciprocating Saw
- Channel Locks
- Hammer
- Phillips Screwdriver
- Tape Measure
- Plumb Line
- 1/4” Self-Tapping Screws
- Framing Material
- Hi-temp Caulking Material
- Gloves
- Safety Glasses
- Framing Square
- Electric Drill & Bits (1/4”)
- Level
May also need:
- Vent Support Straps
- Venting Paint
C. Tools And Supplies Needed
B. Thermostat Wall Control Location
The thermostat wall control’s location will have some a󰀨ect
on the appliance’s operation.
• Maximum wire length from appliance is 100 feet
(30.48m) continuous non-spliced wire. Recommended
18 to 22 gauge wire, solid copper.
• When located close to the appliance, it may require a
slightly higher temperature setting to keep the rest of
the house comfortable.
• When located in an adjacent room or on a di󰀨erent
oor level, you will notice higher temperatures near
the appliance.
D. Inspect Appliance and Components
• Open the appliance and remove all the parts and
articles packed inside the Component Pack. Inspect all
the parts and glass for shipping damage.
• Report to your dealer any parts damaged in shipment.
• All labels have been removed from the glass door.
• Plated surfaces have been wiped clean with a soft
cloth, if applicable.
• Read all the instructions before starting the installation.
Follow these instructions carefully during the
installation to ensure maximum safety and benet.
• Follow pipe manufacturer instructions for installation
and air clearance requirements.
Risk of Fire!
• Damaged parts could impair safe
operation.
• Do NOT install damaged, incomplete or
substitute components.
WARNING
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth &
Home Technologies.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
• Operating appliance without fully assembling
all components.
• Operating appliance without legs attached (if
supplied with appliance).
• Do NOT Over re.
Or any such action that may cause a re hazard.
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:

7June 4, 2019 7027-801C
CB1200 Free Standing
E. Install Checklist
YES IF NO, WHY?
Verified clearance to combustibles.
Appliance is leveled and connector is secured to appliance.
Hearth extension size/height decided.
Outside air kit installed.
Floor protection requirements have been met.
If appliance is connected to a masonry chimney, it should be cleaned and
inspected by a professional. If installed to a factory built metal chimney, the
chimney must be installed according to the manufacturer’s instructions and
clearances.
Appliance Install
Chimney configuration complies with diagrams.
Chimney installed, locked and secured in place with proper clearance.
Chimney meets recommended height requirements (5 feet minimum vertical).
Roof flashing installed and sealed.
Terminations installed and sealed.
Venting/Chimney
Clearances
Verified all clearances meet installation manual requirements.
Mantels and wall projections comply with installation manual requirements.
Floor protection and heart extensions installed per manual requirements.
Appliance Setup
All protective materials removed.
All labels have been removed from the door.
All packaging materials are removed from inside/under appliance.
Manual bag and all of its contents are removed from inside/under the appliance
and given to the party responsible for use and operation.
WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead to a fire or
explosion.
Hearth & Home Technologies recommends the following:
Photographing the installation and copying this checklist for your file.
That this checklist remain visible at all times on the appliance until the installation is complete.
Electrical
120 VAC unswitched power provided to the appliance.
Check outlet with multi-meter for proper polarity and voltage (115-120 VAC).
Record voltage reading: _____________
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
Customer:
Date Installed:
Lot/Address:
Location of Appliance:
Installer:
Dealer/Distributor Phone Number:
Serial Number:
Model Name:
__________________________________________________________________________
______________________________________________________________________
_______________________________________________________________________
________________________________________________________________
___________________________________________________________________________
________________________________________________________
______________________________________________________________________
_______________________________________________________________________
Started appliance and verified that all motors and blowers operate as they should.
Checked draft using a Manometer. Record readings: ______________________
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, ets.) and corrective action needed:
Comments communicated to party responsible __________________________ by ______________________ on ____________
(Builder/Gen. Contractor) (Installer) (Date)
Checked vacuum using a Manometer. Record readings: ____________________

8June 4, 20197027-801C
CB1200 Free Standing
Figure 8.1 - Top View
Figure 8.2 - Side View
Figure 8.3 - Front View
6-1/4
[159]
8
[203]
8
[203]
25-3/4 [654]
27-5/8 [702]
8
[204]
25-3/4 [654]
28-1/2 [724]
31-5/8
[803]
28-1/2 [725]
21-1/4 [539]
10-3/8
[264]
2-3/8
[62]
3-5/8
[94]
5
[127]
14-1/4 [362]
33-3/8
[847]
31-1/4
[795]
2-3/8
[62]
2-3/4
[69]
5
[127]
14-1/4 [362]
Figure 8.4 - Top View with Top Vent Adapter (TPVNT-1) and
O󰀨set Adapter (812-3570)
Figure 8.5 - Side View with Top Vent Adapter (TPVNT-1) and
O󰀨set Adapter (812-3570)
Figure 8.6 - Top View with Top Vent Adapter (TPVNT-1) and
O󰀨set Adapter (811-0720)
3 Dimensions and Clearances
A. Appliance Dimensions

9June 4, 2019 7027-801C
CB1200 Free Standing
33-1/8
[841]
31-1/4
[795]
Figure 9.1 - Side View with Top Vent Adapter (TPVNT-1) and
O󰀨set Adapter (811-0720)
2-3/8
[62]
2-3/4
[69]
3-7/8
[100]
6-1/4
[159]
8
[203]
8
[203]
Figure 9.2 - Top View with Top Vent Adapter (TPVNT-6) and
O󰀨set Adapter (811-0720)
15-51/8
[398]
14
[357]
Figure 9.3 - Side View with Top Vent Adapter (TPVNT-6) and
O󰀨set Adapter (811-0720)

10 June 4, 20197027-801C
CB1200 Free Standing
Installations with:
TPVNT-1 Top Vent Adapter with Heat Shield
and Clean-out
TPVNT-6 Top Vent Adapter with Clean-out
811-0720 (3” to 4”) O󰀨set Adapter
812-3570 (3” to 6”) O󰀨set Adapter
A
B
C
C
D
E
F
G
G
NOTE:
• Illustrations reect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual
design preference.
Horizontal Through the Wall Inches Millimeters
ABack Wall to Appliance 2 51
BSide Wall to Appliance 6 152
Corner Installation Inches Millimeters
CWalls to Appliance 2 51 Vertical Installation Inches Millimeters
DBack Wall to Flue Pipe 3 76
ESide Wall to Appliance Top 6 152
FBack Wall to Appliance 7.5 191
Corner Installation Inches Millimeters
GSide Walls to Appliance 2 51
B. Clearances to Combustibles (UL and ULC)

11June 4, 2019 7027-801C
CB1200 Free Standing
USA INSTALLATIONS: A non-combustible oor protection
is recommended extending beneath the ue pipe when
installed with horizontal venting or under the Top Vent
Adapter with vertical installation.
CANADA INSTALLATIONS: A non-combustible oor
protection extending beneath the ue pipe is required
with horizontal venting or under the Top Vent Adapter with
vertical installation.
33-1/2 in.
minimum
30-3/4 in.
minimum
6 in
(FROM SURFACE OF
GLASS)
6 in
USA
21-1/2 in.
minimum
850mm
minimum
781mm
minimum
152mm
(FROM SURFACE OF
GLASS)
152mm
545mm
minimum
Must extend 51mm
beyond each side
of pipe (shaded area)
to the wall thimble.
CANADA
47-3/4 in.
26-1/4 in.
21-1/2 in.
41-3/8 in.
6 in.
from the fuel door
opening
USA
1214mm
666mm
545mm
1051mm
152mm
(front door opening)
CANADA
Must extend 51mm
beyond each side
of pipe (shaded area)
to the wall thimble.
Figure 11.1
Figure 11.2
Figure 11.3
Figure 11.4
EMBER PROTECTION: It is necessary to install a Type I
oor protector.
Floor protector must be non-combustible material,
extending beneath appliance with a minimum of 6 inches
(152mm) in front of glass and 6 inches (152mm) to both
sides of the fuel loading door. Open the door and measure
6 inches (152mm) from the side edge of the opening in the
face of the appliance.*See exception.
C. Hearth Pad Requirements (UL and ULC)
Fire Risk.
Comply with all minimum clearances to
combustibles as specied.
Failure to comply may cause house re.
WARNING

12 June 4, 20197027-801C
CB1200 Free Standing
A
C
B
D
D. Alcove
Figure 12.1
*All minimums listed are to a combustible surface.
Figure 12.2
Minimum* Maximum
Inches Millimeters Inches Millimeters
AHeight 44 1117 n/a n/a
BWidth 40.5 1029 n/a n/a
CDepth 36 914 36 914
DTo Side Wall 6 152 n/a n/a
NOTE:
• Illustrations reect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual
design preference.

13June 4, 2019 7027-801C
CB1200 Free Standing
4 Vent Information
A. Venting Termination Minimum
Requirements
Figure 13.1 J or K
X
V
M
I
H
A
V
G
B
V
V
A
B
V
FV
C
B
B
E
L
V
D
V
Electrical
Service
V
N
VN
V
N
N
V
Inside Corner
FIXED
CLOSED
OPEN
OPEN
FIXED
CLOSED
VX
G
G
Termination Cap Air Supply Inlet Gas Meter Restricted Area
O
P
A12 in. Above Finish Grade (the grade surface
must be a non-combustible material
B12 in.
48 in. no OAK
Open door or window: below or to the side
B12 in. Open door or window: above
C6 in. Permanently closed window: above, below
or to the side
D18 in.
36 in. no OAK
Vertical clearance to a ventilated so󰀩 t
located above the terminal within a hori-
zontal distance of 2 ft from the center-line
of the terminal
E12 in. Clearance to unventilated so󰀩 t
F12 in. Clearance to outside corner
G12 in. Clearance to inside corner
H36 in. Above gas meter/regulator measured from
horizontal center-line of regulator
I36 in. USA
72 in. Canada
Clearance to service regulator vent outlet
J12 in.
48 in. no OAK
Clearance to non-mechanical air supply
inlet to the building or the combustions air
inlet to any other appliance
K10 ft horizontal
3 ft vertical
Clearance to mechanical air supply
L7 ft. Above paved sidewalk, paved driveway
located on public property
M12 in. Under an open veranda, porch, deck or
balcony
NSee Note
below*
Electric service: above, below or to the
side (location must not obstruct or interfere
with access)
O24 in. Adjacent building, fences and protruding
parts of the structure
P12 in. Clearance above roof line for vertical
terminations
All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.
24 in. Above grass, top of plants, wood or any other combus-
tible
12 in.
36 in. no OAK
Clearance from any forced air intake of other appliance
12 in. Clearance horizontally from combustible wall
15 in. Vented directly through a wall, minimum length of
horizontal pipe
6 in. horizontal
12 in. vertical
Minimum horizontal or vertical terminations must pro-
trude from wall
*NOTE: Consult local building,  re o󰀩 cials or authorities
having jurisdiction. Local codes or regulations
may require di󰀨 erent clearances.
NOTICE: Termination must exhaust above air
inlet elevation.
• It is recommended that at least 60 inches (1.52m) of
vertical pipe be installed when appliance is vented
directly through a wall. This will create a natural draft,
which will help prevent the possibility of smoke or
odor venting into the home during a power outage.
• It will also keep exhaust from causing a nuisance
or hazard by exposing people or shrubs to
high temperatures.
• The safest and preferred venting method is to extend
the vent vertically through the roof or above the roof.
NOTICE: Do NOT Terminate Vent:
• In any location that will allow  ue gases or soot from
entering or staining the building.
• In any location which could create a nuisance
or hazard.
• In any enclosed or semi-enclosed area such as a
carport, garage, attic, crawl space, under a sun deck
or porch, narrow walkway.
• Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.

14 June 4, 20197027-801C
CB1200 Free Standing
B. Avoiding Smoke and Odors
Negative Pressure, Shut-Down and Electrical
Power Failure
To reduce the probability of back-drafting or burn-back
in the pellet appliance during power failure or shut down
conditions, it must be able to draft naturally without exhaust
blower operation.
Negative pressure in the house will resist this natural draft if
not accounted for in the pellet appliance installation.
Heat rises in the house and leaks out at upper levels. This
air must be replaced with cold air from outdoors which
ows into lower levels of the house.
Vents and chimneys into basements and lower levels of the
house can become the conduit for air supply and reverse
under these conditions.
Outside Air
An outside air kit is recommended in all installations. The
Outside Air Kit must be ordered separately.
Per national building codes, consideration must be given
to combustion air supply to all combustion appliances.
Failure to supply adequate combustion air for all appliance
demands may lead to back drafting of those and
other appliances.
When the appliance is roof vented (strongly
recommended):
The air intake is best located on the exterior wall
oriented towards the prevailing wind direction during the
heating season.
When the appliance is side-wall vented:
The air intake is best located on the same exterior wall as
the exhaust vent outlet and located lower on the wall than
the exhaust vent outlet.
The outside air supply kit can supply most of the demands
of the pellet appliance, but consideration must be given to
the total house demand.
House demand may consume the air needed for the
appliance. It may be necessary to add additional ventilation
to the space in which the pellet appliance is located.
Consult with your local HVAC professional to determine the
ventilation demands for your house.
Vent Congurations
When installing a pellet appliance with a horizontal vent
conguration the frequency of power outages should
be considered:
• Power outages during operation will cause the
appliance to immediately turn o󰀨 and may create
conditions where smoke will back draft into the house.
In order to reduce the likelihood of smoke back drafting
into the house during a power outage, Hearth and
Home Technologies strongly suggests:
- Installing the pellet venting with a minimum vertical
run of 5 feet (1.52m).
- Installing the outside air kit at least 4 feet (1.22m)
below the vent termination.
To prevent soot damage to exterior walls of the house and
to prevent re-entry of soot or ash into the house:
• Maintain specied clearances to windows, doors and
air inlets, including air conditioners.
• Vents should not be placed below ventilated so󰀩ts.
Run the vent above the roof.
• Avoid venting into alcove locations.
• Vents should not terminate under overhangs, decks or
onto covered porches.
• Maintain minimum clearance of 12 inches (305mm)
from the vent termination to the exterior wall. If
you see deposits developing on the wall, you may
need to extend this distance to accommodate your
installation conditions.
C. Draft
Draft is the pressure di󰀨erence needed to vent an
appliance successfully. When an appliance is drafting
successfully, all combustion byproducts are exiting the
home through the chimney.
Install through the warm airspace enclosed by the building
envelope. This helps to produce more draft, especially
during lighting and die-down of the re.
Considerations for successful draft include:
• Preventing negative pressure
• Location of appliance and chimney
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of
the chimney system caused by:
• Inadequate draft due to environmental conditions
• Down drafts
• Tight sealing construction of the structure
• Mechanical exhausting devices
CAUTION
• DO NOT CONNECT THIS Appliance TO A CHIMNEY
FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION
DUCT OR SYSTEM.

15June 4, 2019 7027-801C
CB1200 Free Standing
D. Negative Pressure
NOTE: The appliance exhaust outlet is designed to
accommodate 3 inch venting. Use of 4 inch
venting requires the use of a 3-to-4 inch exhaust
vent increaser in addition to any other venting
components needed, sold separately.
Negative pressure results from the imbalance of air
available for the appliance to operate properly. It can be
strongest in lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)
• Range hoods
• Combustion air requirements for furnaces, water
appliances and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air
conditioning
• Imbalances of the HVAC air handling system
• Upper level air leaks such as:
- Recessed lighting
- Attic hatch
- Duct leaks
To minimize the e󰀨ects of negative air pressure:
• Install the outside air kit with the intake facing prevailing
winds during the heating season
• Ensure adequate outdoor air for all combustion
appliances and exhaust equipment
• Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appliance
• Avoid installing the appliance near doors, walkways or
small isolated spaces
• Recessed lighting should be a “sealed can” design
• Attic hatches weather stripped or sealed
• Attic mounted duct work and air handler joints and
seams taped or sealed
E. Chimney and Exhaust Connection
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type “L” or “PL” venting system. It can be
vented vertically or horizontally.
NOTE: All pipe must be welded seam pipe whenever
possible. Seal pipe joints with high temperature
silicone (500°F [260°C] minimum rated only).
2. Mobile Home: Approved for all Listed pellet vent. If
using the 3 inch (76mm) vertical Top Vent Adapter Kit
or the 3 to 6 inch (76-152mm) Top Vent O󰀨set Adapter,
use Listed double wall ue connector. A Quadra-
Fire Outside Air Kit must be used with manufactured
home installations.
3. Residential: The 3 inch (76mm) vertical Top Vent
Adapter Kit and the 3 to 6 inch (76-152mm) Top Vent
O󰀨set Adapter are tested to use 24 gauge single wall
ue connector or Listed double wall ue connector to
Class A Listed metal chimneys, or masonry chimneys
meeting International Residential Code standards for
solid fuel appliances.
4. INSTALL VENT AT CLEARANCES SPECIFIED BY
THE VENT MANUFACTURER.
5. Secure exhaust venting system to the appliance with
at least 3 screws. Also secure all connector pipe joints
with at least 3 screws through each joint.
6. DO NOT INSTALL A FLUE DAMPER IN THE
EXHAUST VENTING SYSTEM OF THIS Appliance.
7. DO NOT CONNECT THIS Appliance TO A CHIMNEY
FLUE SERVING ANOTHER APPLIANCE.
WARNING
Risk of Asphyxiation!
Negative pressure can cause spillage of combustion
fumes and soot.
WARNING
USE ONLY RECOMMENDED VENTING
COMPONENTS; OTHERWISE MAKESHIFT PARTS MAY
RESULT IN PROPERTY DAMAGE, PERSONAL INJURY,
OR DEATH.

16 June 4, 20197027-801C
CB1200 Free Standing
F. Equivalent Feet of Pipe
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent
size (Figure 16.1).
2 ft.
2 ft.
3 ft.
2 ft.
Example of 3 Elbow-Rear Vent Termination Calculation
PELLET
VENTING
COMPONENT
# OF
ELBOWS
FEET
OF
PIPE
MULTIPLIED
BY
EQUIVALENT
FEET
COMPONENTS
EQUIVALENT
FEET
90° Elbow
or Tee 3 X 5 15
45° Elbow X 3
Horizontal Pipe 7 X 1 7
Vertical Pipe 2 X 0.5 1
Total Equivalent Feet 23
NOTE: This is a generic example and is not intended to represent any specic
fuel type.
Figure 16.2
3 in. or 4 in. (76mm or
102mm) Diameter Pipe
3 in. or 4 in. (76mm or
102mm) Diameter Pipe
Equivalent Pipe
Length In Feet
Equivalent Pipe
Length In Feet
ALTITUDE IN THOUSANDS OF FEETALTITUDE IN THOUSANDS OF FEET
0
20
30
1 2 3 4 5 6 7 8 9 10
4 in. (102mm) Diameter Pipe Only4 in. (102mm) Diameter Pipe Only
10
Example 1Example 1
Example 2
Example 2
Example 1: If the equivalent length of pipe is 23 feet (7m)
with altitude of 8,000 feet (2438m) you must use
4 inch (102mm) diameter type “L” or “PL” vent.
Example 2: If the equivalent length of pipe is 12 feet (3.7m)
with altitude of 6,000 feet (1829m) you may use
3 or 4 inch (76 to 102mm) diameter type “L” or
“PL” vent.
G. Pipe Selection Chart
The chart will help you in determining proper venting
size according to the equivalent feet of pipe calculated
previously and the altitude above sea level of this
installation (Figure 16.2).
a. Locate the calculated equivalent feet of pipe on the
vertical left side of the chart.
b. Move to the right horizontally on the chart until you
reach your altitude above sea level.
c. If you fall below the diagonal line, 3 or 4 inch (76 to
102mm) pipe may be used.
d. If it is anywhere above the diagonal line, a 4 inch
(102mm) diameter pipe is required.
Figure 16.1
Risk of Injury or Property Damage.
• Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
• Refer to the owner’s information manual
provided with this appliance.
• For assistance or additional information
consult a qualied installer, service
agency or your dealer.
WARNING
Vent surfaces get HOT, can cause burns
if touched. Non-combustible shielding or
guards may be required.
WARNING
Risk of Fire!
• Only LISTED venting components may
be used.
• NO OTHER vent components may
be used.
• Substitute or damaged vent components
may impair safe operation.
WARNING
NOTICE:
• A 90° elbow is 5 times as restrictive to the ow of
exhaust gases under positive pressure as 1 foot
(305mm) of horizontal pipe.
• A foot of horizontal pipe is twice as restrictive as a
foot of vertical pipe.

17June 4, 2019 7027-801C
CB1200 Free Standing
Straight Out
Figure 17.1
Figure 17.2
45 Degree
Wall
Thimble
Illustration shows venting going in both directions.
Choose which one is best for your installation.
2 in. (51mm)
Minimum
2 in. (51mm)
Minimum
6 in.
(152mm)
Minimum
6 in. (152mm)
Minimum
6 in.
(152mm)
Minimum
Non-combustible Hearth Pad
Wall
Thimble
Horizontal
Termination
Cap
2 in.
(51mm)
Minimum
6 in.
(152mm)
Minimum
From Glass
5 Venting Systems
A. Through The Wall
Horizontal termination cap must be a minimum of 6
inches. (152mm) from the wall. Approved for mobile home
installations. Must use 3 or 4 inch (76-102mm) “L” or “PL”
Listed pellet venting or Listed double wall pipe and a
Quadra-Fire Outside Air Kit in mobile homes.
NOTE: In Canada, where passage through a wall or
partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365.
NOTICE: Please note that while the minimum clearance
for the termination cap is 6 inches (152mm)
there is the possibility of soot build-up around
the termination area. If this occurs we suggest
to move the termination further away from the
house to prevent it.
We strongly recommend that you DO NOT DOWNWARD
VENT. The following may occur:
• The appliance will not vent properly
• Smoke spillage in the house
• Excessive sooting
CAUTION

18 June 4, 20197027-801C
CB1200 Free Standing
C. Through The Wall & Vertical - Exterior
Figure 18.1
Figure 18.2
D. Vertical - Interior - Typical Installation
Figure 18.3
Firestop
Flashing
Rain Cap
6 in.
(152mm)
Min.
Non-combustible Hearth Pad
3 in. (76mm)
Min.
Clean-out
Cover
12 in. (305mm)
minimum
Ceiling Support
Class A Chimney
Connector Adapter
Top Vent Kit
Non-combustible Hearth Pad
Clean-out Cover
Tee
Wall Thimble
Support Bracket
every 60 in. (1524mm)
12 in. (305mm)
Minimum
Rain Cap
Flashing
2 in. (51mm) Minimum
6 in. (152mm)
Minimum
Firestop
Flashing
Rain Cap
6 in.
(152mm)
Min.
Non-combustible Hearth Pad
3 in. (76mm) Min.
12 in.
(305mm)
Minimum
3 in. to 3 in.
(76-76mm)
Top Vent Kit
Clean-out Cover
All three installations are approved for mobile home
installations. Must use 3 or 4 inch (76 to 102mm) “L” or “PL”
Listed pellet venting or Listed double wall pipe and Quadra-
Fire Outside Air Kit in mobile homes. Single wall pipe is
approved for residential installations only.
B. Vertical into Existing Class A Chimney
*NOTE: Clearance to combustibles are for standard
pellet pipe. If pellet pipe manufacturer allows
reduced clearances to their pipe, reduced
clearances are allowed.
NOTE: A chimney connector shall not pass through an
attic or roof space, closet or similar concealed
space, or a oor or ceiling.

19June 4, 2019 7027-801C
CB1200 Free Standing
E. Masonry
F. Alternate Masonry
Figure 19.1
Figure 19.2
Non-Combustible Hearth Pad
Airtight
Clean-out Door
Cleanout Cover
Sheathing
3 in. (76mm) Minimum
1 in. (25mm) Clearance
Flashing
Fireclay Flue
Liner with Airspace
Concrete Cap
1 in. (25mm) Clearance
with Firestop
6
in. (152mm)
M
inimum
Non-Combustible Hearth Pad
Sheathing
2 in. (51mm) Minimum
1 in. (25mm)
Clearance
Flashing
Fireclay Flue Liner
with Airspace
Concrete Cap
6 in. (152mm)
Minimum
Airtight Clean-out Door
1 in. (25mm) Clearance
with Firestop
Fire Risk.
Inspection of Chimney:
• Masonry chimney must be in
good condition.
• Meets minimum standard of NFPA 211.
• Factory-built chimney must be a minimum
6 inch (152mm) UL103 HT.
WARNING

20 June 4, 20197027-801C
CB1200 Free Standing
6 Appliance Set-Up
A. Outside Air Kit Instructions
Included in Kit: 1 piece of 2 inch x 3 foot ex hose, 2 hose
clamps, 1 collar assembly, termination cap assembly, 1 trim
ring, 12 screws.
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
1. Rear Installation
a. Measure distance from oor to air vent opening in
appliance and mark location on wall.
b. Use saw to cut opening in wall. Cut a 2-1/2 to 3
inch (64-76mm) opening on inside wall and a 3 to
3-1/2 inch (76-89mm) opening on outside of house.
c. Use hose clamp to secure ex pipe to
collar assembly.
d. Slide trim ring over ex pipe and run pipe
through wall.
e. Attach hose to outside termination cap with second
hose clamp.
f. Secure termination cap to outside surface.
g. Secure trim ring to interior wall.
h. Snip corners and remove plate (Figure 20.1).
i. Align and secure collar assembly with 2 of the 4
holes as shown (Figure 20.2).
Flex Hose
Hose Clamp
Collar Assembly
Trim Ring
Termination
Cap Assembly
Hose Clamp
Air Intake Channel
(Discard)
Figure 20.2
Figure 20.1
Snip Corners
and remove
plate
NO
NO
Secure Collar
Screen
Install Cover Plat
e
Seal Pedestal with 26 in. Rope
Figure 20.4
Figure 20.3
2. Floor Installation
a. Remove rear screen and set aside.
b. Install cover plate over hole in right rear oor.
c. Cut a 2 inch minimum hole in the oor to
accommodate ex hose.
d. Attach hose to termination cap.
e. Place rope under pedestal to close o󰀨 air leaks.
CAUTION
Never draw outside combustion air from:
• Wall, oor or ceiling cavity.
• Enclosed space such as an attic or garage.