Quantum P7000 Series User manual

Document 6434006-02, Ver. 2, Rel. 0, August 2002 1
Quantum ATL P7000
Unpacking Instructions
Introduction 3
Selecting an Installation Location 4
Floor Space .....................................................................................................4
Floor Clearance ..............................................................................................4
Floor Strength and Inclination.....................................................................5
Power and Grounding..................................................................................5
Environmental Conditions...........................................................................6
Preparing for the Installation 6
Providing Necessary Tools and Equipment..............................................6
Taking ESD Precautions ...............................................................................6
Unpacking the Library 7
Receiving the Library....................................................................................7
Unboxing the Library ...................................................................................8
Positioning the Library...............................................................................13
Unpacking the Library................................................................................16
Storing the Shipping Materials..................................................................20
Leveling the Library....................................................................................21

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
2 6207947-04fN 11

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
Introduction 3
Introduction 0
The Quantum ATL P7000 is an automated storage and retrieval library
consisting of up to 16 tape drives and up to 679 digital linear tape
(DLT™) cartridges see figure 1.
This document explains how to unpack the ATL P7000. Once the
library is unpacked and moved to the desired installation location, set
up the library using the instructions in the Quantum ATL P4000 and
ATL P7000 Tape Libraries User’s Guide.
Figure 1 ATL P7000
Library

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
4 Selecting an Installation Location
Selecting an Installation Location 0
When choosing an installation site for the ATL P7000, consider the
following requirements:
• Floor space
• Floor clearance
• Floor strength and inclination
• Power and grounding
• Environmental conditions
These requirements are also described in the Quantum ATL P4000 and
ATL P7000 Tape Libraries User’s Guide.
Floor Space 0Figure 2 shows the minimum floor space required by the ATL P7000.
Figure 2 Floor Space
Requirements
Floor Clearance 0The library has a floor clearance of 0.75 inch (19 mm). Place the library
on a level, uncarpeted floor free of defects.
6 ft 10 in (2.08 m)
9 ft 4 in (2.8 m)
29 in (74 cm)
27 in (69 cm)
60 in (152 cm)
26 in (66cm)
27 in (69 cm)

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
Selecting an Installation Location 5
Floor Strength and
Inclination 0
The floor at the installation site must be rated at 250 lb/ft2
(1221 kg/m2). This is sufficient to support a fully loaded ATL P7000
library.
The floor must be level to within 0.25 inch (6.4 mm) over a 6-foot-by-6-
foot (1.83-meter-by-1.83-meter) area.
Power and
Grounding 0
For the United States and Canada, one or two UL/CSA certified power
cords are furnished. Each uses a 14/3 SJT cord, a 5-20P plug, and an
IEC-C320 C19 female connector (see figure 3).
Figure 3 Power Supply
Cord
The library is rated 100-240V~, 50-60Hz, 16A-8A, 1600W.
The library power requirements may require modification of the
facilities existing power capabilities by a qualified electrician. The
required wall outlet for the United States and Canada is rated at 125V
20A (see figure 4).
Figure 4 Wall Outlet
The dedicated wall outlet and a 20 amp circuit breaker must provide
power to the ATL P7000 only. Outside North America, replace the
supplied power cord with a harmonized 3 x 1.5 mm2power cord that
is approved by the country where used, and install the appropriate
wall outlet. More information on the electrical requirements is
provided in the ATL P7000 Pre-Installation Site Survey Instructions.
Caution: The ATL P7000 must be connected to a grounded
electrical outlet.
Plug:
NEMA 5-20
Connector:
IEC-C320 C19
Connects to
wall outlet
Connect to library
power supply
Neutral
Ground
Line Wall outlet:
NEMA 5-20R
rated 125V 20A

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
6 Preparing for the Installation
Environmental
Conditions 0
The installation site must have the following environmental
conditions:
• Humidity: 20%-80% non-condensing
• Temperature: 15°C-32°C (59°F-90°F)
• Altitude: sea level to 10,000 feet
These environmental conditions apply when the library is in
operation.
Preparing for the Installation 0
Before you begin the installation procedure in this section, make the
following preparations as described in this section:
• Providing necessary tools and equipment for installation
• Taking ESD precautions
Providing Necessary
Tools and Equipment 0
Provide the following tools for unpacking the library:
•Scissors
• Ratchet with 15/16 inch socket (or 15/16 inch open-end wrench)
Provide the following tools for removing the shipping restraints:
• #2 Phillips® screwdriver
•Tiewrap
Provide the following tools for leveling the library:
• 3/4-inch open-end wrench
• Carpenter’s level
Taking ESD
Precautions 0
Some components within the ATL P7000 contain static-sensitive parts.
To avoid damaging these parts while performing installation
procedures, always observe the following precautions:
• Keep the library turned off during all installation procedures.
Note: For additional library specifications (including
environmental requirements during shipping and storage),
see appendix A in the Quantum ATL P4000 and ATL P7000
Tape Libraries User’s Guide.

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
Unpacking the Library 7
• Keep the library power cord plugged into a grounded power
outlet except when working with AC electrical components.
• Avoid contact with power supplies, EMI filters, and AC electrical
components while the library is connected to a power outlet.
• Use an antistatic wrist strap.
• Keep static-sensitive parts in their original shipping containers
until ready for installation.
• Do not place static-sensitive parts on a metal surface. Place them
inside their protective shipping bag or on an antistatic mat.
• Avoid touching connectors and other components.
Unpacking the Library 0
This section explains how to unpack the library and move it to its final
installation location. The ATL P7000 is shipped in packing materials
designed to protect it from damage during transit. By following these
instructions, you help ensure that the library will continue to be
safeguarded after it arrives at the installation site.
The following are the major steps in this procedure:
• Receiving the library
• Unboxing the library
• Positioning the library
• Unpacking the library
• Leveling the library
Receiving the Library 0Unpack the library as close to the installation site as possible. Inspect
the shipping pallet and carton for damage that may have occurred
during shipment. Report any damage to the shipper.
Note: Dry climates and cold-weather heating environments have
lower relative humidity and are more likely to produce static
electricity.
Caution: The ATL P7000 with 16 DLT7000 tape drives weighs
approximately 1444 pounds (656 kg). Use at least two
people to move and install the library.

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
8 Unpacking the Library
Unboxing the Library 0To unbox the library:
1Choose the unloading side. The ATL P7000 may be unloaded from
either the right or left side of the pallet.
2Verify the minimum floor space requirements (see figure 5).
Figure 5 Minimum Floor
Space Requirements—
Uncrating Site
3Cut the two steel bands that secure the library and packing
material to the pallet (see figure 6).
Note: Uncrating the library requires a minimum of 3 feet
(91 cm) on all sides. For the side being used for the ramp,
uncrating the library requires an additional 7 feet (2.13
m) for a total of 10 feet (3.05 m) on that side. Figure 5
shows the minimum floor space required by the ATL
P7000 at its uncrating site. The minimum height required
for unpacking the ATL P7000 is 85 inches (2.16 meters).
Caution: The steel bands are under tension and will snap
away when cut.
3 ft (92cm) 3 ft (92cm)
3 ft (92cm) 3 ft (92cm)
Front
Rear
Accessory kits
Library
Ramp extensions
10 ft (3.05 m) for ramp extensions
10 ft (3.05 m) for ramp extensions

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
Unpacking the Library 9
Figure 6 Removing the
Steel Bands
4Lift the cardboard box top cover straight up and off of the pallet
(see figure 7).
Figure 7 Removing the
Box Top Cover
5Pull the eight cardboard box retaining clips to their open position.
6Unwrap the cardboard box from the library (see figure 8).

Quantum ATL P7000 Unpacking Instructions
Document 6434006-02, Ver. 2, Rel. 0
August 2002
10 Unpacking the Library
Figure 8 Removing the
Cardboard Box
7Remove the accessory kits from the rear compartment of the crate.
8Check the packing list and verify that all accessories have been
received.
9Lift the foam cap up and off of the library (see figure 9).
Note: If any part is missing or damaged, contact your
authorized reseller.