Quantum QN-H-220 User manual

www.qntmnet.com
Quick Setup Guide
Model: QN-H-220
High Performance 802.11ac (2x2) Wave 2 Indoor (Room) Access Point

www.qntmnet.com
Contents
Before You Begin..................................................................................................................................3
Package Contents................................................................................................................................3
Prerequisites.........................................................................................................................................3
Connect Access Point..........................................................................................................................3
Step 1- Access Point Initial Configuration ..........................................................................................4
Step 2- Setting Up Device IP Address................................................................................................4
Step 3- Access Point Quick Setup in Standalone Mode ...................................................................5
Step 4- Access Point Quick Setup in Cloud Controlled Mode..........................................................6
Step 5- Create New Account on QN-RUDDER .................................................................................6
Reset Access Point to Factory Defaults.............................................................................................7
Access Point Default Login Detail.......................................................................................................7
FCC Statement.....................................................................................................................................8

www.qntmnet.com
This Quick Setup Guide provides step-by-step instructions on how to set up Quantum Networks’
Access Point. After completing the steps described in this Guide, you will be able to install the
Access Point (AP) on site and provide wireless network access to users.
Before You Begin
Your Quantum Networks’Access Point can work in “Standalone Mode” or can be managed by
“Cloud Controller”.
To manage Access Point by “Cloud Controller”, please follow step 5 first and then step 1. For
“Standalone Mode”, continue with step 1.
Quantum Networks’ Cloud Controller (QN-RUDDER) is a cloud hosted controller which can
be used to configure, manage & monitor devices associated with it. It can be accessed from
https://cc.qntmnet.com
Package Contents
• Access Point
• Quick Setup Guide
Prerequisites
Internet access
Desktop / Laptop / Handheld device
802.3af / 802.3at PoE Switch / PoE Injector
Connect Access Point
After unpacking Access Point, connect it to Internet source
Plug in Ethernet cable of Access Point
Power on Access Point by using 802.3af / 802.3at PoE Switch / PoE Injector
Note: Access Point must have internet access during initial setup for the first time to activate
the device, warranty and support.

www.qntmnet.com
Step 1- Access Point Initial Configuration
Connect WAN port of the Access Point to network with internet access.
You should see a new wireless network with SSID QN_XX:XX (where XX:XX are last
four digits of Access Point MAC Address).
Connect to QN_XX:XX SSID and browse Access Point’s default IP “169.254.1.1”. You
should be greeted with welcome message.
Figure 1
Step 2- Setting Up Device IP Address
Click Start Configuration (Refer Figure1).
Configure IPv4 by selecting required option DHCP, Static or PPPoE and click Next.
Figure 2

www.qntmnet.com
Management Mode
Quantum Networks’Access Point can be configured in two modes:
Standalone
Independent management of each Access Point
Cloud Controlled
Centralized management of Access Points using QN-RUDDER
Step 3- Access Point Quick Setup in Standalone Mode
Select “Management Mode” as “Standalone”, if each Access Point is to be configured
and managed individually. Define username and password for the device and click
“Next”.
User can select Access Point’s Operation Mode as Bridge or Router.
Description: Difference between Access Point as a Bridge or a Router.
Bridge - In this mode, device connects to a wired or wireless router via an
ethernet cable and extends the wireless coverage of your existing network.
Router - In this mode, device connects to the internet directly and share internet
access to multiple wired and wireless devices. NAT and DHCP servers are
enabled by default
Bridge
Configure WLAN (SSID) parameters and click Next.
Review the Configuration Summary. Click Reconfigure if any changes are
required or click Finish to complete the configuration.
Router
Configure WLAN (SSID) and Local subnet parameters and click Next.
Review the Configuration Summary. Click Reconfigure if any changes are
required or click Finish to complete the configuration.

www.qntmnet.com
Step 4- Access Point Quick Setup in Cloud Controlled Mode
Select “Management Mode” as “Cloud Controlled”,enter cloud login credentials and
click “NEXT”.(If you do not have an account on QN-RUDDER, please refer Step 5)
Select Cloud Controller site, where Access Point needs to be added and click “Next”.
User can select Access Point Operation Mode as Bridge or Router.
Bridge
Select Operation Mode as Bridge and click “Next”.
Configure WLAN (SSID) parameters, click Next and review the
Configuration Summary.
If a site has predefined wireless network in cloud, the device would
import settings and redirect to Configuration Summary.
Click Reconfigure if any changes required or click Finish to complete the
Configuration.
Router
Configure WLAN (SSID) and Local subnet parameters and click “Next”.
If you do not want to create WLAN (SSID)/LAN now, click Skip, it will
redirect to Configuration Summary.
Review the Configuration Summary. Click Reconfigure if any changes
are required or click Finish to complete the configuration.
Step 5- Create New Account on QN-RUDDER
Browse https://cc.qntmnet.com.
Click “Create New Account” to sign up for a new account.
Figure 3

www.qntmnet.com
Follow the steps as guided on screen for Registration.
Verify QN-RUDDER account from registered email id.
Your Account on QN-RUDDER (Quantum Networks’ Cloud Controller) is now ready to
use.
Reset Access Point to Factory Defaults
oPower on the Access Point
oPush the reset button on back panel and hold it for 10 seconds.
oAccess Point would restart with factory defaults
Access Point Default Login Detail
User Name: As Defined while creating account
Password: Auto Generated
Password will be sent to registered email on QN-RUDDER.
If you encounter problems while installing or using this product, please browse
www.qntmnet.com for:
Direct contact to the support center.
Frequently Asked Questions (FAQ)
Download area for the latest software, user documentation and product updates.

www.qntmnet.com
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Consult the dealer or an experienced radio/TV technician for help.
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.