Quatech DP-PCIE-100 User manual

May/07 MN2000000087
1
DP-PCIE-100
User Manual
Ver. 2.00
All brand names and trademarks are properties of their
respective owners.

May/07 MN2000000087
2
Features and Benefits
Features zCompliant with PCI Express Base Specification
1.0a
zSupports Standard Parallel Port(SPP), Enhanced
Parallel Port(EPP) & Enhanced Capability
Port(ECP)
zData transfer rate up to 1.5MB/Sec
zSupport Windows® 2000, XP, Server 2003, Vista
Bus zPCI-Express X1
Connectors z2 x 25 pins parallel connectors
Package Contents
z1 x DP-PCIE-100 Card
z1 x Bracket with one DB25 female parallel port
z1 x Driver CD
System Requirements
zWindows® 2000/XP/Server 2003/Vista
zPCI Express-enabled system with an available PCI Express slot

May/07 MN2000000087
3
Hardware Installation
1. Turn Off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCIe slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Replace the computer cover and reconnect the power cord.
Driver Installation
Please make sure the board is installed before proceeding with driver
installation.

May/07 MN2000000087
4
For Windows® 2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), and click Next.
3. Check Specify a location, uncheck the other boxes, then click
Next.
4. Insert the Driver CD, type in the following
D:\Drivers\PCIExpress\DP-PCIE-100\2000, then click OK.
(Change D: to match your CD-ROM driver letter)
5. Click Next and Finish.
6. Restart Windows to complete the installation.
For Windows® XP
1. At the Found New Hardware Wizard, select Install from a list
or specific location (Advanced), then click Next.
2. Insert the Driver CD, check Include this location in the search,
uncheck the other boxes, type in the following:
D:\Drivers\PCIExpress\DP-PCIE-100\XP, then click OK.
(Change D: to match your CD-ROM drive letter)
3. If the Hardware Installation window pops up, click Continue

May/07 MN2000000087
5
Anyway, then Finish. Our driver has been thoroughly tested for
stability and compatibility.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
For Windows® Server 2003
1. At the Found New Hardware Wizard, select Install from a list
or specific location (Advanced), then click Next.
2. Insert the Driver CD, check Include this location in the search,
uncheck the other box, type in the following:
D:\Drivers\PCIExpress\DP-PCIE-100\2003, then click OK.
(Change D: to match your CD-ROM drive letter)
3. If the Hardware Installation window pops up, click Continue
Anyway, then Finish. Our driver has been thoroughly tested for
stability and compatibility.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
For Windows® Vista
1. At the Found New Hardware Wizard, select Locate and install
driver software (recommended).

May/07 MN2000000087
6
2. Click on I don’t have the disc. Show me other options.
3. Select the option Browse my computer for driver software
(advanced).
4. Insert the driver CD, check Include subfolders, type in
D:\Drivers\PCIExpress\DP-PCIE-100\Vista32, then click Next.
(Change D: to match your CD-ROM drive letter)
5. If the system prompts the user informing the drivers are not
signed, select the option Install this driver software anyway.
6. Click on Close to complete the driver installation.
To Verify Windows® Driver Installation
1. Right click My Computer, then click Manage. Click Device
Manager.
2. Click on the + (plus sign) in front of Ports(COM & LPT), two
MosChip PCI Parallel Port … should be displayed.
3. Double click Multifunction adapters, MosChip PCI Multi-I/O
Controller should be displayed.
Change The Parallel Port Number
Some parallel devices need a specific parallel port number in order to

May/07 MN2000000087
7
work. If your parallel device works properly, do not change this setting.
For Windows® 2000/XP/Server 20003/Vista Installation
1. From the Device Manager window double click Ports(COM &
LPT), then double click the MosChip PCI Parallel Port
2. Click Port Settings tab.
3. At the LPT Port Number box, click the down arrow and select
an LPT port that is not in use.
4. Click OK, then close Device Manager to save the changes.