Quest Engineering 506 Manual

INSTALLATION, OPERATION AND
MAINTENANCE INSTRUCTIONS
QUEST
506
QUESTCLIMATE.COM / [phone]
Patents: thermastor.com/patents
Serial Number
Install Date
Sold By
TS-1016 01/22 REV J
Quiet operation
230V & 277V units
Long-life impeller
Industry-leading efficiency
Superior MERV-13 air filtration
Environmentally friendly refrigerant
Auto-restart after power outages

2
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
TABLE OF CONTENTS
Safety Precautions............................................................3
1. Intended Application....................................................4
2. Registrations .................................................................4
3. Specifications................................................................4
4. Installation .....................................................................5
4.1 Location...................................................................5
4.2 Electrical Requirements .....................................5
4.3 Condensate Water Removal ...............................6
4.4 Hanging .................................................................6
5. Controls..... .....................................................................7
5.1 Humidity Control....................................................7
5.2 24VAC Wiring ........................................................7
5.2A Deh 3000R...................................................8
5.2B Honeywell Remote Humidistat.................8
5.2C Daisy Chain...................................................8
6. Maintenance ..................................................................8
6.1 Standard Air Filter.................................................9
7. Service............................................................................9
7.1 Warranty...................................................................9
7.2 Technical Description...........................................9
7.3 Troublshooting.......................................................9
8. Ducting Guidelines.......................... ............................ 11
Wiring Diagram........................................................... 12
Service Parts List ............................................................ 13
Optional Parts List .......................................................... 13
Warranty......... ................................................................... 14
4201 Lien Rd. Madison, WI 53704
1-800-533-7533
Thermastor.com | QuestClimate.com
© 2016 Therma-Stor LLC

3
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
SAFETY PRECAUTIONS
Read the installation, operation and maintenance instructions carefully before installing and
operating this device. Proper adherence to these instructions is essential to obtain maximum benefit
from your Quest Dehumidifier.
READ AND SAVE THESE INSTRUCTIONS
• The device is designed to be installed INDOORS IN A SPACE THAT IS
PROTECTED FROM RAIN AND FLOODING.
• Install the unit with space to access the back or side panels for
maintenance and service. DO NOT INSTALL UNIT WITH THE SERVICE
PANELS INACCESSIBLE.
• Avoid directing the discharge air at people, or over the water in pool
areas.
• If used near a pool, spa or water; be certain there is NO chance the unit
could fall into the water, be splashed and that it is plugged into an outlet
that is a GROUND FAULT INTERRUPT protected circuit.
• DO NOT use the device as a bench or table.
• DO NOT place the device directly on structural members. Provide vibration
isolation in order to minimize operational vibration and/or noise.
• A drain pan MUST be placed under the unit if installed above a living area
or above an area where water leakage could cause damage
• Never operate a unit with a damaged power cord. If the power cord is
damaged it must be replaced by the manufacturer, its service agent, or
similarly qualified person in order to avoid a hazard.
• Make all electrical connections in accordance with the current edition of
the NEC ANSI/NFPA 70 and any national and local codes or ordinances
that may apply.
• Maintain a minimum 3ft. (1m) clearance to avoid obstructing the air return
and supply.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
• Not intended for use at altitudes over 2000M.

4
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
1. INTENDED APPLICATION FOR QUEST 506
The Quest 506 Dehumidifier is designed to operate in temperatures between 56 F and 95 F.
In order to efficiently control humidity levels, the area in which the dehumidifier is to be operated must
be free of water intrusion or excessive fresh (outside) air infiltration. Before installing the Quest 506
Dehumidifier, water intrusion and air infiltration problems should be addressed or noted in calculations.
2. REGISTRATIONS
The Quest 506 Dehumidifier units conform to unified standards: UL 60335-2-40, CSA 22.2 # 60335-2-
40:2012 Ed. 1+4. Patent: thermastor.com/patents
3. SPECIFICATIONS @ 80°F/60% RH
UNIT QUEST 506
4036600
QUEST 506 277V
4036610
CFM: 1350@0.0” WG 1350@0.0” WG
POWER: 2700 Watts 2700 Watts
SUPPLY VOLTAGE: 220-240 VAC
1 Phase - 60 Hz
277 VAC
1 Phase - 60 Hz
CURRENT DRAW: 11.0A 10.0A
RATED CURRENT
DRAW (AMPS):
(104 F |36%)
13.6A 12.2A
ENERGY FACTOR: 3.8 L/kWh 3.8 L/kWh
OPERATING TEMP: 56 F Min - 95 F Max 56 F Min - 95 F Max
WATER REMOVAL:
EFFICIENCY:
506 Pints/Day
8.1 Pints/kWh
506 Pints/Day
8.1 Pints/kWh
AIR FILTER: MERV-13 Size: 18” x 20” x 2” MERV-13 Size: 18” x 20” x 2”
POWER CORD:
14ga 10’, NEMA 6-20P 12ga 10’, NEMA L7-20P
DRAIN
CONNECTION: 3/4” Threaded NPT 3/4” Threaded NPT
REFRIGERANT TYPE:
REFRIGERANT
AMOUNT:
R410A
4 lb 8 oz
R410A
4 lb 8 oz
DIMENSIONS:
WIDTH:
HEIGHT:
LENGTH:
WEIGHT:
Unit Shipping
28.9” 36”
33.8” 40”
44.7” 48”
280 lb 340 lb
Unit Shipping
28.9” 36”
33.8” 40”
44.7” 48”
280 lb 340 lb
* Unit 4036600 requires buck/boost transformer to run on 208V or 277V
* Both units require external control not provided

5
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
4. INSTALLATION
4.1 LOCATION
The Quest 506 Dehumidifier can be installed in a variety of locations to meet the owner’s needs as
listed below. In all cases keep the following cautions in mind:
• It is designed to be installed INDOORS IN A SPACE THAT IS PROTECTED FROM RAIN AND
FLOODING.
• Install the unit with space to access side panel for maintenance and service. DO NOT INSTALL
UNIT WITH ACCESS PANEL INACCESSIBLE.
• Avoid discharging the air directly at people, or over the water in pool areas.
• Be certain there is NO chance the unit could fall into water or be splashed and that it is plugged
into a GROUND FAULT INTERRUPTER.
• DO NOT use the Quest 506 Dehumidifier as a bench or table.
• DO NOT place the Quest 506 Dehumidifier directly on structural members. Provide vibration
isolation in order to minimize operational vibration and/or noise.
• A drain pan MUST be placed under the unit if installed above an area where water leakage could
cause damage.
• DO NOT obstruct the supply or return air. Maintain a minimum 3’ clearance around supply and
return air.
4.2 ELECTRICAL REQUIREMENTS
WARNING! Electrical shock hazard: Electrical power must be present for
some test. These test should be performed by a qualified service person.
The Quest 506 dehumidifier plugs into NEMA 6-20R rated receptacle. The Quest 506 277v
dehumidifer plugs into a NEMA L7-20P rated receptacle. The amp draws are listed on page 4 of
this manual. Connecting to electrical power must comply with all national, state and local electrical
codes. A ground fault interrupter protected circuit is recommended. This unit shall not be used with
an extension cord.
WARNING! The On/Off switch above the 24VAC control reset only turns off
the 24VAC circuit. It does not disconnect the main power.
Low Voltage Connections
Install the external control in a central area of the structure where it will sense the relative humidity
accurately. Do not install the control sensor where it may not accurately measure the relative
humidity such as near HVAC supply registers, near exterior doors or near pool or spas. The installer
must supply the wiring between the dehumidifier and the external control. Be sure to safely route
the control wiring to prevent damage during installation. Be careful not to cross the wires when
connecting the dehumidifier and the external control.
The controls of the dehumidifier are powered by a low voltage circuit (24VAC) and must NEVER contact
or be connected to a high voltage circuit. The control terminals are labeled to prevent confusion.
WARNING! Damaged power cords can only be replaced with one by the unit
manufacturer.

6
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
4.3 CONDENSATE WATER REMOVAL
Condensate drains by gravity via the drain port. Use 3/4” male NPT PVC pipe. An optional
condensate pump kit may be installed if a lift is required to dispose of the condensate. Optional parts
list for information on the kit.
FOLLOW DIAGRAM:
• Level within 2°
Vent:
• Place vent after the trap.
• Vent should be open.
• Height of vent should be higher than drain outlet.
Cap:
• A clean out can be placed before trap but must be
sealed with a cap.
Drain Line:
• Drain line should go in a downward slope to the drain.
• 1/4” drop per foot.
4.4 HANGING DIAGRAM
PARTS NEEDED: 4 pieces 3/8” threaded rod (not included)
4 - 3/8” threaded jam nuts (not included)
WARNING! Hanging installation must meet all state and local codes.
28.95
27.25
3/8” threaded rod
Intake Air
Treated Air
3/8” Jam Nuts
5.56”
Drain Trap Configuration
VENT OPEN
CAP
2”
6.75”
4”
3/4” drain port

7
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
WARNING! Installation should be done by a qualified agency in accordance
with these instructions. The qualified service agency installing this high efficiency
refrigeration system is responsible for the installation.
WARNING! Check the supporting structure to be used to verify that it has
sufficient load carrying capacity to support the weight of the unit. Suspend the unit
only from the threaded nut retainers. Do NOT suspend from the cabinet.
CAUTION! Recommended maximum hanger rod is 6 feet (1.8m).
5. CONTROL OPTIONS
The Quest 506 Dehumidifier is controlled by an external remote humidistat through a 24V terminal
block. External control NOT provided.
5.1 HUMIDITY CONTROL
A 24VAC signal is sent by the remote humidistat signals the fan or fan and compressor to actuate.
QUEST CONTROL OPTIONS:
• Cloud Control
• Quest DEH3000R
• Honeywell Humidipro
• Any 24V signal to Dehumidify
CAUTION! Low Voltage Hazard. Can cause equipment damage. Disconnect
power before beginning installation.
5.2 24VAC WIRING
The terminal block, low voltage circuit breaker, and power switch are located on the intake side of the
unit. Turn the power switch to the off position while wiring the unit.
FLOAT: {External normally closed dry contact float switch.} No voltage may be applied to
the float switch.
FLOAT: Applying voltage may damage the control and void the warranty. {If no float is
used in the system, leave the jumper connected to the terminal block.}
DEHU: Dehumidificaton (compressor and fan operation).
R: 24VAC output
FAN: Fan operation only.
C: 24VAC neutral (common)
Note:
External devices can be powered between 24V/COM (10VA max).
24V circuit is protected by circuit breaker.
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT

8
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
5.2A CLOUD CONTROL 5.2A DEH 3000R CONTROL 5.2B HONEYWELL
REMOTE HUMIDISTAT
5.2C DAISY CHAIN
24VAC
COMP FAN
HONEYWELL REMOTE HUMIDISTAT
WIRING DIAGRAM
QUEST DEH 3000R CONTROL
WIRING DIAGRAM
Red
Black
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
24VAC
COMP FAN
HONEYWELL REMOTE HUMIDISTAT
WIRING DIAGRAM
QUEST DEH 3000R CONTROL
WIRING DIAGRAM
Red
Black
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
24VAC
COMP FAN
QUEST DEH 3000R CONTROLER
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
QUEST 6 SERIES -
UNIT#2
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
QUEST 6 SERIES -
UNIT#3
QUEST 6 SERIES -
UNIT#1
*NOTE - DO NOT WIRE IN “FAN” TERMINAL WITH THIS APPLICATION
C
FAN
R
DHUM
(COMPRESSOR
AND FAN)
FLOAT
FLOAT
24V IN COM 24V OUT
(RED)
(YELLOW)
(BLUE)
QUEST CLOUD CONTROL
WIRING DIAGRAM
6. MAINTENANCE
WARNING! Do not operate the unit without the filter or with a less effective
filter. The heat exchange coils inside the unit could become clogged and require
disassembly to clean. Filter non-compliance invalidates the product warranty.

9
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
6.1 STANDARD AIR FILTER
The Quest 506 Dehumidifier ships with a standard MERV 13 efficient pleated fabric filter. This filter
should be checked every six months. Operating the unit with a dirty filter will reduce dehumidifier
capacity and efficiency and may cause the compressor to cycle off and on unnecessarily on the
defrost control.
To access the air filter, the filter should be readily visible and can be removed by pulling it straight
out of the Quest 506 Dehumidifier.
We recommend changing the filter at least with every grow cycle.
7. SERVICE
WARNING! Servicing the Quest 506 with its high pressure refrigerant
system and high voltage circuitry presents a health hazard which could result in
death, serious bodily injury, and/or property damage. Only qualified service people
should service this unit.
7.1 WARRANTY
A warranty certificate has been enclosed with this unit; read it before any repair is initiated. If a
warranty repair is required, call the factory first at 1-877-420-1330 for warranty claim authorization
and technical assistance.
7.2 TECHNICAL DESCRIPTION (NON STANDARD PATENTED)
The Quest 506 Dehumidifier uses a refrigeration system similar to an air conditioner’s to remove
heat and moisture from incoming air, and add heat to the air that is discharged.
Hot, high-pressure refrigerant gas is routed from the compressor to the condenser coil. The
refrigerant is cooled and condensed by giving up its heat to the air that is about to be discharged
from the unit. The refrigerant liquid then passes through a filter/drier and expansion drier which
causes the refrigerant pressure and temperature to drop. It next enters the evaporator coil where the
cool refrigerant absorbs heat from the incoming air and evaporates.
The compressor evacuates the cool refrigerant vapor from the evaporator and compresses it to a
high pressure and temperature to repeat the process.
7.3 TROUBLESHOOTING
Neither fan nor compressor running. Dehumidification is being called for. No fan call.
1. Unit unplugged or no power to outlet.
2. Humidity control set too high.
3. Loose connection in internal or control wiring.
4. Defective Compressor relay.
5. Defective control transformer.
Compressor is not running. Dehumidification is being called for. No fan call.
1. Defective compressor run capacitor.
2. Loose connection in compressor circuit.
3. Defective compressor overload.
4. Defective compressor.
5. Defrost thermostat open.

10
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
Compressor cycles on and off. Dehumidification is being called for. Fan is running.
1. Low ambient temperature and/or humidity causing unit to cycle through defrost mode.
2. Defective compressor overload.
3. Defective compressor.
4. Defrost thermostat defective.
5. Dirty air filter(s) or air flow restricted.
Fan is not running. Dehumidification or fan is being called for.
1. Loose connection in fan circuit.
2. Obstruction prevents fan impeller rotation.
3. Defective fan.
4. Defective fan relay.
Low dehumidification capacity (evaporator is frosted continuously). Dehumidification is being called for.
1. Defrost sensor loose or defective.
2. Low refrigerant charge
3. Dirty air filter(s) or air flow restricted.
4. Excessively restrictive ducting connected to unit.
Unit removes some water, but not as much as expected.
1. Air temperature and/or humidity have dropped.
2. Humidity meter and or thermometer used are out of calibration.
3. Unit has entered defrost cycle.
4. Air filter dirty.
5. Defective defrost sensor.
6. Low refrigerant charge.
7. Air leak such as loose cover or ducting leaks.
8. Defective compressor.
9. Restrictive ducting.
10. Optional Condensate Pump Safety Switch open.
Test to determine if the problem is with the unit or control:
1. Detach field control wiring connections from unit.
2. Connect the 24V and FAN together; only the impeller fan should run. Disconnect the wires.
3. Connect the 24V and DEHU together; fan should run, Compressor should come on after a short delay.
4. Run the unit for 1 hour in an environment that is greater than a 50 F dew point. The unit should
produce water from the drain port.
5. If these tests pass, the unit is working properly. You should check the control and field wiring for
problems if the unit is not activating. Check for air restrictions, low temperature, low humidity and
refrigerant charge if the unit is not producing water.

11
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
8. DUCTING GUIDELINES
CAUTION! Quest 506 is intended for use in statics under .25”WG.
• Ducting either the intake or exhaust use a minimum of two 12” diameter round ducts minimum.
• Grills or diffusers on the duct ends must not excessively restrict airflow.
• Effective dehumidification may require ducting to be branched to isolated or stagnant flow areas.
Be sure to use appropriate size duct branches to maintain proper feed throughout the ducting
system.
• System control should be placed remotely from the dehumidifier in a central location.
• Intake and exhaust ducting should have a minimum of 4 feet from the unit before any turns.
CAUTION! Do not connect with a static pressure greater than +.25”wg.
Contact technical support for additional details.
• Optional duct kits are available from the factory: Exhaust Kit 4038641 and Intake Kit 4038642.
See figures below for plenum dimensions and duct diameters. Alternatively, licensed contractors
can fabricate duct plenums and reference figures below for safe fastener mounting points.
QUEST 6 SERIES
506 SUPPLY
DUCT LOCATION
4”
27 3/4”
RECTANGULAR
DUCT SIZE
7 1/8”
13 5/8” 1 7/8”7 1/8”
21 3/4”
RECTANGULAR
DUCT SIZE
1 5/8”
7 1/2”
6 7/8”
2 X 12” DUCT
COLLAR
2 X 12” DUCT
COLLAR
21 1/4”
RECTANGULAR
DUCT SIZE
10 5/8”
3 1/8”
2 1/4” 10 1/8” 16 1/4”
36 3/8”
RECTANGULAR
DUCT SIZE
12 3/4”
15 7/8”
QUEST 6 SERIES
506 INTAKE DUCT
LOCATION

12
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
WIRING DIAGRAM OF THE QUEST 506 DEHUMIDIFIER

13
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
SERVICE PARTS LIST
Item Part No Description
1 4029507 CONTROL,HIGH PRESSURE
2 4029508 CONTROL,LOW PRESSURE
3 4029575 RELAY
4 4031101 CONTACTOR
5 4031406 TRANSFORMER
(4042945) TRANSFORMER (277V)
6 4035949-06 CAPACITOR,COMP.
(4035949-12) CAPACITOR,COMP. (277V)
7 4036164-20 TUBE,CU,CPLRY
8 4036559 CIRCUIT BREAKER
9 4039729 CLAMP,CAPACITOR
10 4037221-06 CAPACITOR
(4042209-04) CAPACITOR (277V)
11 4037699 THERMISTOR
12 4039607 CPRSR
(4042942) CPRSR (277V)
13 4037702 FILTER,DRIER
Item Part No Description
14 4037703-04 COIL,EVAP
15 4037704-02 COIL,CONDENSER
16 4037707 TXV,3 TON
17 4037708 FAN,MOTORIZED IMPELLER
(4042941) FAN,MOTORIZED IMPELLER (277V)
18 4037728 CORD
(4042899) CORD (277V)
19 4038135 HANDLE,POCKET
20 4038136 BEZEL,HANDLE
21 4038178 WIRE HARNESS
22 4038079 LUG,GROUND
23 4038219 FOOT,RUBBER,1.25” DIA
24 4038225-01 BRACKET,FOOT,RIGHT
25 4038226-01 BRACKET,FOOT LEFT
26 4038215 BLOCK, WIRING
27 4039691 CONTROL ASSY
28 4038233 FILTER (QTY 2)
Part No Qty Description
4020175 1 Controller, Humidity
4028531 1 DEH 3000R Control, Remote
4041550 1 Cloud Control
4041560 1 Cloud Control Plus
Part No Qty Description
4032220 1 Kit, Pump
4038642 1 Kit, Intake Duct
4038641 1 Kit, Exhaust Duct
4038644 1 Drain Trap Kit
OPTIONAL PARTS LIST
1
17
2
19, 20
6
23
24
25
10
12
3
13
14
28
15
16
8
27
9
4
5
26
22

14
QUEST 506 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
QUESTCLIMATE.COM(877) 420-1330
QUEST 506 DEHUMIDIFIER LIMITED WARRANTY
WARRANTOR:
Therma-Stor LLC
4201 Lien Rd
Madison, WI 53704
Telephone: [phone]
WHO IS COVERED: This warranty extends only to the original end-user of the Quest 506
Dehumidifier dehumidifier, and may not be assigned or transferred.
FIRST YEAR WARRANTY: Therma-Stor LLC warrants that, for one (1) year the Quest 506 Dehumidifier
dehumidifier will operate free from any defects in materials and workmanship, or Therma-Stor LLC
will, at its option, repair or replace the defective part(s), free of any charge.
SECOND THROUGH FIFTH YEAR WARRANTY: Therma-Stor LLC further warrants that for a period
of five (5) years, the condenser, evaporator, and compressor of the Quest 506 Dehumidifier
dehumidifier will operate free of any defects in material or workmanship, or Therma-Stor LLC, at its
option, will repair or replace the defective part(s), provided that all labor and transportation charges
for the part(s) shall be borne by the end-user.
END-USER RESPONSIBILITIES: Warranty service must be performed by a Servicer authorized by
Therma-Stor LLC. If the end-user is unable to locate or obtain warranty service from an authorized
Servicer, he should call Therma-Stor LLC at the above number and ask for the Therma-Stor LLC
Service Department, which will then arrange for covered warranty service. Warranty service will be
performed during normal working hours.
The End-user must present proof of purchase (lease) upon request, by use of the warranty card or
other reasonable and reliable means. The end-user is responsible for normal care. This warranty does
not cover any defect, malfunction, etc. resulting from misuse, abuse, lack of normal care, corrosion,
freezing, tampering, modification, unauthorized or improper repair or installation, accident, acts of
nature or any other cause beyond Therma-Stor LLC's reasonable control.
LIMITATIONS AND EXCLUSIONS: If any Quest 506 Dehumidifier part is repaired or replaced, the new
part shall be warranted for only the remainder of the original warranty period applicable thereto (but
all warranty periods will be extended by the period of time, if any, that the Quest 506 Dehumidifier is
out of service while awaiting covered warranty service).
UPON THE EXPIRATION OF THE WRITTEN WARRANTY APPLICABLE TO THE Quest Dual DEHUMIDIFIER OR ANY PART THEREOF,
ALL OTHER WARRANTIES IMPLIED BY LAW, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL ALSO EXPIRE. ALL WARRANTIES MADE BY THERMA-STOR LLC ARE SET FORTH HEREIN, AND NO CLAIM MAY BE MADE
AGAINST THERMA-STOR LLC BASED ON ANY ORAL WARRANTY. IN NO EVENT SHALL THERMA-STOR LLC, IN CONNECTION WITH
THE SALE, INSTALLATION, USE, REPAIR OR REPLACEMENT OF ANY Quest Dual DEHUMIDIFIER OR PART THEREOF BE LIABLE
UNDER ANY LEGAL THEORY FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION
WATER DAMAGE (THE END-USER SHOULD TAKE PRECAUTIONS AGAINST SAME), LOST PROFITS, DELAY, OR LOSS OF USE OR
DAMAGE TO ANY REAL OR PERSONAL PROPERTY.
Some states do not allow limitations on how long an implied warranty lasts, and some do not allow
the exclusion or limitation of incidental or consequential damages, so one or both of these limitation
may not apply to you.
LEGAL RIGHTS: This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.