Quoizel CSE9010EK Mounting instructions

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-CSE9010_R1
For Styles CSE9010PN and CSE9010EK
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Package Contents
A
Mounting
Screw
x3
Figure 1
STEP 1 remove Fixture
Hood, Shade and Styrofoam
from Fixture Body
-
A. Remove Fixture Hood by
unlock Lock Screw from
Fixture Body (G).
B. Remove the Package
Material and Shade inside
the Fixture Body (G).
Lock Screw
Fixture
Hood
B
Shade
STEP 2 Install Shade, Fixture
Hood and Bulb to Fixture Body
-
A. Pass Lock Washer (D), Fixture
Hood and Water Proof Washer
(B) over the Nipple (E), secure
by threading Finial (B) onto
Nipple (E). Hand tighten until
sung.
B. Insert bulb and screw snugly into
place.
C. Place Shade (G) into Fixture
Body (F) properly. Then Place
the Fixture Hood onto the top
edge of the Fixture Body (F) and
secure with Lock Screws.
Tighten until snug.
Fixture
Hood
Lock
Screw
F
Figure 2
BFinial
x1
C
Water Proof
Washer
x1
D
Lock
Washer
x1 ENipple
x1
Fixture
Body
x1
F
Shade
x1 G
D
E
G
B
C
Package
Material
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)MediumBase150WbulbMaximumor
(1)MediumBaseVintageBulbisrecommendedbutnotsupplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Vintage Bulb
(recommended
but not supplied)
STEP 3 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
Post
Lighting
Post
Post
Fixture
Fitter
Figure 4
2017 QuoizelInc. RevisedDate:2017-10-25

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 4 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
STEP 5 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 4 above.
1/16” bit and drill
STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Post
Post
Figure 4
Figure 5
Figure 6
STEP 7 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Your fixture is now assembled and ready to use.
Enjoy!
Post
Hole
Fixture
Fitter
Mounting
Hole
Post
Lighting
A
Figure 7
CSE9010PN
FINISH: PALLADIAN BRONZE
CSE9010EK
FINISH: EARTH BLACK
10” Dia.
7” Dia.
17.25”
10.5”
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
2017 QuoizelInc. RevisedDate:2017-10-25