1of2
Figure 3
STEP 2 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (BB) if your
installation requires a shorter mounting screw.
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (AA).
Place the backplate and Fixture Body (A) onto the Crossbar
Assembly (AA) and secure with mounting balls. Note: The
backplate and Fixture Body (A) should be snug against the wall and
held tight with the mounting balls. If it is not, adjust the length of the
mounting screws or alternate short mounting screws on the
Crossbar Assembly (AA) by unscrewing the preassembled hex nut
and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate and Fixture Body (A)
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
(3)B10CandelabraBaseBulbs60WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
Warnings and Cautions
Assembly Instruction Sheet #IS-MBH8411W
For Style MBH8411W
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Figure 2
Hex Nut and
Lock Washer
A
Mounting Ball
Mounting Screw
or Alternate Short
Mounting Screw Backplate
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
is secure, remove the
mounting ball and
Fixture Body (A) and
proceed to Step 4.
Hardware Contents
Package Contents
D
B
Cage
x1
Tab
x2
AA
Crossbar
Assembly
x1
STEP 1 Install Shade-
A. Place the Glass Shade (C) into the
Cage (D). Secure by pressing Tabs
(B) onto the Cage (D) and top edge
of the Glass Shade (C).
B. Place the sockets of the Fixture
Body (A) inside of the Glass Shade
(C). Align the label “A” on the bottom
edge of the fixture hood to the label
“A” on the top edge of the Cage (D).
Attach the fixture hood of the Fixture
Body (A) to the top edge of the Cage
(D). Secure them together with Lock
Screws (E). Hand tighten until snug
with screwdrivers.
A
Fixture
Body
x1
CGlass Shade
x1
Figure 1
ELock Screw
x3
A
B
C
D
E
BB
Alternate
Mounting
screw
x2
Label “A”
Label “A”
AA
AA
ReleasedDate:2017-08-02
