Quoizel HGN9010WT User manual

Package Contents
Warnings and Cautions
1of2
For Style HGN9010WT
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
markingpen,1/16”
drillbit,centerpunch,hammer,drillandwrench.
(1)A21MediumBaseBulb150WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,
Installation Guide #IS-HGN9010WT
2019 QuoizelInc. ReleasedDate:2019-03-22
visit us on-line at www.quoizel.com
AMounting Screw
x3
BScrew
x2
C
Fixture Body
x1
STEP 1 Remove Cage from the
Fixture Body
-
A. Unlock screws on the bracket and
remove the cage from the Fixture
Body (C).
Figure 1
Glass Shade
x1
D
STEP 3 Install Glass Shade-
A. Remove the lock ball and flat
washer from the nipple in the top
center of the cage.
B. Place the Glass Shade (D) into
the cage and pass the center
hole on the top of the Glass
Shade (D) over the nipple in the
top center of the cage. Secure
Glass Shade (D) by threading
previously removed flat washer
and lock ball back onto the
nipple. Hand tighten until snug.
Cage
Screw
Bracket
C
STEP 2 Install Bulb-
A. Insert the bulb onto the socket
and screw snugly into place.
Figure 2
Socket
Vintage Bulb
(recommended
but not included)
Cage
Nipple
D
Flat Washer
Lock Ball
Figure 3
STEP 4 Install Cage with
Glass Shade
-
A. Place the cage with glass
shade onto the bracket and
secure with previously
removed screws. Hand
tighten until snug. Cage with
Glass Shade
Screw
Bracket
C
Figure 4

2of2
2019 QuoizelInc. ReleasedDate:2019-03-22
visit us on-line at www.quoizel.com
STEP 5 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting Hole
Post Lighting
Post
Post
Fixture
Fitter
Figure 5
STEP 6 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
Figure 7
STEP 7 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 6 above.
1/16” bit and drill
Post
STEP 8 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Figure 6
Figure 8
STEP 9 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Your fixture is now assembled and ready to use. Enjoy!
Post
Hole
Fixture Fitter
Mounting Hole
Post Lighting
A
Figure 9
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
HGN9010WT
FINISH: WESTERN BRONZE
9.5” Dia.
11”
17.5”
7.5” Dia.