Quoizel SNNL9009K User manual

1of2
Pleasegoto forproductcleaningtips.Gotothe selection.
LED16W
Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
Package Contents
Fixture Body
x1 B
A
Mounting
Screw
x3
For Styles SNNL9009K and SNNL9009PN
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
STEP 1 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
STEP 2 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
Lighting
Post
Post
Post
Fixture
Fitter
Figure 1
Figure 2
STEP 3 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 2 above.
1/16” bit and drill
STEP 4 - Wire Connections
A. Use standard wire connectors (C) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Post
Figure 3
Figure 4
STEP 5 Attach the fixture to
the Post Mount
-
A. Place the fixture on the post
lining up the mounting holes
on the fixture fitter with the
holes on the post. Use the
Mounting Screws (A) to
attach the fixture to the post.
Your fixture is now
assembled and ready to use.
Enjoy!Post
Hole
Fixture
Fitter
Mounting
Hole
Post
Lighting
A
Figure 5
Installation Guide #IS-SNNL9009
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Wire Connector
x3
C
ReleasedDate:2019-08-09

2of2
HOW TO REPLACE GLASS PANELS
Allen Screw
Screw
Fixture
Hood
Glass
Holder
Glass
Panel
Cage
A.
Fixture Hood.
Remove Cage with
Glass Panels from the
fixture.
B. Unscrew Screws from
the Cage and remove
Glass Holders. Replace
Glass Panels from the
Cage and then re-install
Glass Holders. Secure
with removed Screws.
C. Attach Cage with Glass
Panels back onto the
Fixture Hood and
secure with Allen
Screws.
Unlock Allen Screws on
the
2018 QuoizelInc. ReleasedDate:2019-08-09
visit us on-line at www.quoizel.com