Quoizel OAS8409Z Mounting instructions

Part Description Quantity
A Crossbar 1pc.
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
Fixture Body
B
C
D
E
F
Hex Nut
Lock Washer
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
A
B
C
D
F
E
Mounting Ball
Mounting Screw
Assembly Instruction Sheet #IS-OAS8409
For Style OAS8409Z
1of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)CandelabraBase60WMaximum
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagrams
belowtobesureallpartsarepresent.Ifanypartsaremissingordamaged,donotattempttoassemble,install,or
operatethefixture.Contactcustomerserviceforreplacementparts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safety
glasses.
November2015
Rev.A

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
2of5
(3)60W candelabra
base bulbs
(not Supplied)
14.5”
23”
9” 11”
6”
6”
2
1
Rev.A
OAS8409Z
FINISH: MEDICI BRONZE
1
2
PART NUMBER
M2253CCZ
9453KIT
REPLACEMENT PART DESCRIPTION
CANDLE COVER MEDC BRNZ 2”H
MTG HDW MEDC BRNZ 4”D
REQ.
3
1
NO.

STEP 2 -Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Crossbar
Outlet
Box
Outlet Box
Screw
Mounting
Hole
Figure 2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
3of5
STEP 1 -Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the backplate of the Fixture Body (F).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex
Nut (D) onto the Mounting Screws (B). Hand tighten
until snug.
Figure 1
Crossbar
Mounting Screw
Lock Washer
Hex Nut
Fixture
Body
November2015
Rev.A
Assembly Instruction Sheet #IS-OAS8409
For Style OAS8409Z
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
4of5
STEP 4 -Attach Fixture Body to Mounting
Screw
A. Place the backplate of the Fixture Body (F) over the
Mounting Screws (B) and secure with Mounting Balls
(E). Hand tighten until snug.
Mounting Screw
Mounting Ball
Backplate
Figure 5
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
Figure 4
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Figure 3
November2015
Rev.A
Assembly Instruction Sheet #IS-OAS8409
For Style OAS8409Z
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
5of5
STEP 5 -Install Bulb
A. standard bulb with a candelabra screw
base 0
This fixture uses
. Maximum 6 watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place. Socket
Figure 6
Bulb
STEP 6 Apply Silicone Sealer to Mounting
Balls
-
A. To prevent moisture from entering the wire
compartment, apply a small amount of silicone sealer
(not included) to the threaded side of the mounting
balls (E) and then install them onto the mounting
screws (B). Wipe off excess caulk.
STEP 7 Apply Silicone Sealer to Backplate-
A. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, start on one side of fixture backplate and
follow contour, where the fixture backplate meets the
exterior wall surface upward. Proceed to caulk over top
of backplate and down other side. Do not caulk bottom
of fixture backplate to ensure proper moisture
drainage.
Your lamp wall fixture is now assembled and ready to
use. Enjoy!
Figure 7
Mounting Ball
Figure 8
Glass
Frame
November2015
Rev.A
Mounting
Screw
Exterior
Grade Caulk
Outdoor
Fixture
Backplate
Exterior Wall Surface
Assembly Instruction Sheet #IS-OAS8409
For Style OAS8409Z
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..