Quoizel WKF8411EK Mounting instructions

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-WKF8411EK
For Style WKF8411EK
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
ACrossbar Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBasebulbs60WMaximumor
(3)CandelabraBaseT8Vintage bulbs are recommended but not supplied.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
CFixture Body
x1
B
Alternate
Mounting screw
x2
ReleasedDate:2017-09-29
D
Glass
Panel
x4
STEP 1 Install Glass Panels-
A. Unscrew screws from the top edge
of the Cage (E) to remove glass
holder.
B. Insert Glass Panels (D) into the slot
in the bottom edge of the Cage (E).
Attach the glass holder onto the top
edge of Glass Panels (D) and align
holes on it to mounting holes on the
Cage (E). Secure the glass holder
with removed screws. Tighten
gently until snug with screwdrivers.
D
Screw
ECage
x1
E
Slot
Glass
Holder
STEP 2 Install Cage-
A. Remove lock screws from the bottom edge of the fixture hood.
B. E
Attach the Cage (E) with glass
panels to the fixture hood and secure with removed lock screws.
Hand tighten until snug with screwdrivers.
Align the label “A” on the top edge of the Cage ( ) to the label “A” in
the bottom edge of the fixture hood.
Label “A”
Label “A”
C
E
Lock Screw
Figure 2
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box A
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 3

2of2
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-09-29
Figure 4
STEP 4 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw or
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
screwing the mounting
screws or alternate short
mounting screws in or out
of the crossbar until the
correct length is
achieved. Once the
backplate and Fixture
Body (C) is secure,
remove the mounting ball
and Fixture Body (C) and
proceed to Step 5.
STEP 5 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 5
STEP 6 Install the Fixture Body-
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the mounting balls
until snug.
Figure 6
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
Exterior
Grade Caulk
Backplate
Exterior
Grade Caulk
STEP 7 Install Bulbs and Apply Silicone Sealer-
A. Insert bulbs onto sockets and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over top
of backplate and down both sides. Do not caulk the bottom of the
fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Figure 7
Socket
T8 Vintage Bulb
(recommended
but not supplied)
WKF8411EK
FINISH: EARTH BLACK
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
2.75”
8.5”
17”
11.75” 5.5”
10.75”
Fixture can
only be
mounted in
the direction
indicated